Chauvet Mayhem User Manual

Snapshot

Use on Dimmer

Outdoor Use

Sound Activated

DMX

Master/Slave

Autoswitching

Power Supply

Replaceable Fuse

User Serviceable

Duty Cycle

User Manual

3000 N 29th Ct, Hollywood, FL 33020 U.S.A.

[phone] – [phone]

FAX [phone]

www.chauvetlighting.com

TABLE OF CONTENTS

1. BEFORE YOU BEGIN ................................................................................................................................................... 3

WHAT IS INCLUDED ................................................................................................................................................................................ 3

UNPACKING INSTRUCTIONS .................................................................................................................................................................... 3

MANUAL CONVENTIONS ......................................................................................................................................................................... 3

ICONS .................................................................................................................................................................................................. 3

SAFETY INSTRUCTIONS .......................................................................................................................................................................... 4

2. INTRODUCTION ........................................................................................................................................................... 5

FEATURES ............................................................................................................................................................................................ 5

ADDITIONAL FEATURES .......................................................................................................................................................................... 5

PRODUCT DIMENSIONS .......................................................................................................................................................................... 5

PRODUCT OVERVIEW............................................................................................................................................................................. 6

3. SETUP .......................................................................................................................................................................... 7

AC POWER........................................................................................................................................................................................... 7

Power Linking ........................................................................................................................................................... 7

MOUNTING............................................................................................................................................................................................ 8

Orientation ................................................................................................................................................................ 8

Rigging ..................................................................................................................................................................... 8

4. OPERATING INSTRUCTIONS ...................................................................................................................................... 9

DMX Operation ......................................................................................................................................................... 9

Master/Slave Mode (Sound-Active, Auto Mode, Static Colors) .................................................................................. 9

STANDALONE OPERATION .................................................................................................................................................................... 10

Automatic ................................................................................................................................................................ 10

Sound-Active .......................................................................................................................................................... 10

Custom Program ..................................................................................................................................................... 10

DMX CHANNEL VALUES ...................................................................................................................................................................... 11

5. APPENDIX .................................................................................................................................................................. 12

DMX PRIMER ..................................................................................................................................................................................... 12

GENERAL MAINTENANCE...................................................................................................................................................................... 12

NEVER SPIN A FAN USING COMPRESSED AIR. .......................................................................................................................................... 12

FIXTURE LINKING................................................................................................................................................................................. 13

Data Cabling ........................................................................................................................................................... 13

DMX Data Cable ..................................................................................................................................................... 13

Cable Connectors ................................................................................................................................................... 13

3-Pin to 5-Pin Conversion Chart .............................................................................................................................. 14

Setting up a DMX Serial Data Link .......................................................................................................................... 14

SETTING THE STARTING ADDRESS ........................................................................................................................................................ 15

GENERAL TROUBLESHOOTING .............................................................................................................................................................. 15

CONTACT US ...................................................................................................................................................................................... 15

RETURNS PROCEDURE ........................................................................................................................................................................ 16

CLAIMS .............................................................................................................................................................................................. 16

TECHNICAL SPECIFICATIONS ................................................................................................................................................................ 17

1. BEFORE YOU BEGIN

CONVENTION

MEANING

[10]

A DIP switch to be configured

<Menu>

A key to be pressed on the fixture’s control panel

1~512

A range of values

50/60

A set of values of which only one can be chosen

Settings

A menu option not to be modified (for example, showing the operating mode/current status)

MENU > Settings

A sequence of menu options to be followed

ON

A value to be entered or selected

ICONS

MEANING

This paragraph contains critical installation, configuration or operation information. Failure
to comply with this information may render the fixture partially or completely inoperative,
cause damage to the fixture or cause harm to the user.

This paragraph contains important installation or configuration information. Failure to
comply with this information may prevent the fixture from functioning correctly.

This paragraph reminds you of useful, although not critical, information.

What is included

 1 x Mayhem™
 1 x Power cable
 1 x Warranty Card

Unpacking Instructions

Manual Conventions

 1 x User Manual

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.

CHAUVET manuals use the following conventions to differentiate certain types of information from
the regular text.

Icons

This manual uses the following icons to indicate information that requires special attention on the part
of the user.

1. Before You Begin 3 11/13/2009 3:17 PM

Safety Instructions

Please read these instructions carefully. It includes important
information about the installation, usage and maintenance of this
product.

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

Always make sure that you are connecting to the proper voltage, and that the line voltage you are

connecting to is not higher than that stated on the decal or rear panel of the fixture.

This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to

rain or moisture.
Make sure there are no flammable materials close to the unit while operating.
The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent

surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or replacing fuse and be sure to replace with

same fuse source.
Secure fixture to fastening device using a safety chain.
Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher

than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair the

unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center.
Never connect the device to a dimmer pack.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Never carry the fixture directly from the cord. Always use the hanging/mounting bracket.
Avoid direct eye exposure to the light source while it is on.

1. Before You Begin 4 11/13/2009 3:17 PM

2. INTRODUCTION

Features

7-channel DMX-512 dual rotating LED scanner
Individual control of red, green and blue LEDs for each side (with strobing)
Individual control of motor direction and speed for each side
Instantly set motors and/or LEDs into sound activated programs
Built-in automated programs via master/slave or DMX
Built-in sound activated programs via master/slave or DMX

Additional Features

High-power, 3 W (700 mA) LEDs
Additional power output: max 25 units

Product Dimensions

2. Introduction 5 11/13/2009 3:17 PM

Safety

DMX In

Power Input

(IEC)

Microphone

Audio

Adjustment

Knob

Fuseholder

Light Output

Bracket
Adjustment Knob

DMX Out

Power Output

(Edison)

Bracket
Adjustment Knob

DIP switches

Product Overview

2. Introduction 6 11/13/2009 3:17 PM

Additional

power link

Fixture #1

Fixture #1

Fixture #1

3. SETUP

AC Power

This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage

to which you are connecting it is within the range of accepted voltages.

Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat

(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0

to 100% switch.

To determine the power requirements for a particular fixture, see the label affixed to the back plate of

the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its

average current draw under normal conditions.

Always connect the fixture to a circuit with a suitable electrical ground.

Power Linking

This fixture contains power linking via the edison outlet located in front of the power input cable.

Please see the diagram below for further explanation.

The maximum quantity of fixtures that may be linked is 25.

4. Operating Instructions 7 11/13/2009 3:17 PM

Rotating mirror

(1 of 2)

Mounting

Bracket

Bracket

Adjustment knob

Mounting

Orientation

The Mayhem™ may be mounted in any safe position, provided there is adequate room for
ventilation.

Rigging

Be sure that the structure can support the weight of the fixture. Please see the “Technical

Specifications” section of this manual for a detailed weight listing. Mount the fixture

securely. This may be done with a screw, nut and bolt, or a hanging clamp. The hole in
each bracket is 13 mm in size. When rigging, consider routine maintenance and DIP switch
access. Please see the following steps for installation.

If the power link out is intended to be used with multiple fixture, take into account the

length of each power cable, and mount the fixtures close enough to one another to
accommodate for this.

When aiming the fixtures, you may use the bracket adjustment knob. Loosen the

knob, adjust to the desired angle, and then tighten the knob by turning clockwise. Do
not use tools for this step, as it may cause damage.

Safety cables must always be used.

4. Operating Instructions 8 11/13/2009 3:17 PM

4. OPERATING INSTRUCTIONS

DMX Operation

Master/Slave Mode (Sound-Active, Auto Mode, Static Colors)

This is the operating mode which will allow for control with an external DMX controller. You must set

the starting address for this mode. If this is your first time using DMX, then it is recommended that

you refer to the “DMX Primer” section in the “Appendix” of this manual.

The fixture will automatically switch to DMX operating mode when a DMX controller is plugged into

the fixture.

Mode DIP switches

DMX 1~9 = set to the DMX starting address

This mode allows a single unit to run a standalone program, while 1 or more other units follow the

same operation. This requires the fixtures to be linked with DMX cables. Please see the section on

Fixture Linking.

1) Turn switch to the Slave position on the slave units, and they will react the same as the Master.
The Master can be set to either Automatic or Sound-Active mode.

Mode DIP switches

Slave 1~10 = Off

4. Operating Instructions 9 11/13/2009 3:17 PM

Standalone Operation

Automatic

Sound-Active

Custom Program

This fixture has a preprogrammed color fade program. This is accessed via the DIP switches on the
back of the fixture, and the speed may be adjusted, as well. Please see the chart below for further
explanation.

Mode DIP switches
Master Auto 9 = On

This fixture has preprogrammed sound triggered chases. These are accessed via the DIP switches
on the back of the fixture, and the sensitivity may be adjusted using the audio adjustment knob.
Please see the chart below for further explanation.

Mode DIP switches
Master Sound 8 = On

You may combine functions together to create a desired look. These are accessed via the DIP
switches on the back of the fixture, and the sensitivity may be adjusted using the audio adjustment
knob. Please see the chart below for further explanation.

Mode DIP switches
Red 1 = On
Green 2 = On
Blue 3 = On
Strobe Speed 1 4 = On
Strobe Speed 2 5 = On
Strobe Speed 3 6 = On
Strobe Speed 4 7 = On
Reverse Motors 10 = On

.

4. Operating Instructions 10 11/13/2009 3:17 PM

DMX Channel Values

CHANNEL

VALUE

FUNCTION

1

000  020
021  040
041  060
061  080
081  100
101  120
121  140
141  160
161  180
181  200
201  220
221  240
241  255

Mode

Static Color
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
Mode 11
Sound

2

000  009
010  255

Strobe

No function
Slow  fast

3

000  009
010  255

Run Speed

No function
Slow  fast

4

(POD 1)

000  020
021  040
041  060
061  080
081  100
101  120
121  140
141  255

Static Color

No function
Red
Green
Blue
Red/Green
Red/Blue
Green/Blue
Red/Green/Blue

5

(POD 2)

6

(POD 1)

000  020
021  040
041  060
061  080
081  100
101  120
121  140
141  160
161  180
181  200
201  220
221  240
241  255

Motor Rotation

Static Color
(clockwise) speed 1 (slowest)
(clockwise) speed 2
(clockwise) speed 3
(clockwise) speed 4
(clockwise) speed 5 (fastest)
No rotation
(counter-clockwise) speed 1 (slowest)
(counter-clockwise) speed 2
(counter-clockwise) speed 3
(counter-clockwise) speed 4
(counter-clockwise) speed 5 (fastest)
Sound

7

(POD 2)

4. Operating Instructions 11 11/13/2009 3:17 PM

5. APPENDIX

DMX Primer

There are 512 channels in a DMX connection. Channels may be assigned in any manner. A fixture
capable of receiving DMX will require one or a number of sequential channels. The user must assign
a starting address on the fixture that indicates the first channel reserved in the controller. There are
many different types of DMX controllable fixtures and they all may vary in the total number of
channels required. Choosing a start address should be planned in advance. Channels should never
overlap. If they do, this will result in erratic operation of the fixtures whose starting address is set
incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+).

General Maintenance

To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.

Unplug fixture from power.
Use a vacuum or air compressor and a soft brush to remove dust collected on external

vents.

Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl

Alcohol and a soft lint free cotton cloth or lens tissue.
Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
Gently polish optical surfaces until they are free of haze and lint.

The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the fixture operates. Damp, smoky
or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. Clean
with soft cloth using normal glass cleaning fluid. Clean the external optics at least every 20 days.
Clean the fixture at least every 30/60 days.

Always dry the parts carefully after cleaning them.

Never spin a fan using compressed air.

5. Appendix 12 11/13/2009 3:17 PM

COMMON

DMX +

DMX -

INPUT

OUTPUT

1 3 2

1

3

2

1

3

2

120 ohm ¼ W
resistor between
pin 2 (DMX -) and
pin 3 (DMX +) on
the output of the
last fixture

To avoid signal transmission problems
and interference, it is always advisable to
connect a DMX signal terminator.

DMX connector configuration

Fixture Linking

You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures
the data link can support.

Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA­485 standard, no more than 32 fixtures should be connected on one data link. Connecting
more than 32 fixtures on one serial data link without the use of a DMX optically-isolated
splitter may result in deterioration of the digital DMX signal.

Maximum recommended serial data link distance: 500 m (1640 ft)
Maximum recommended number of fixtures on a serial data link: 32

Data Cabling

To link fixtures together you must obtain data cables. You can purchase CHAUVET certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.

DMX Data Cable

Use a Belden© 9841 or equivalent cable which meets the specifications for EIA RS-485 applications.
Standard microphone cables cannot transmit DMX data reliably over long distances. The cable must
have the following characteristics:

Type: shielded, 2-conductor twisted pair
Maximum capacitance between conductors: 30 pF/ft
Maximum capacitance between conductor and shield: 55 pF/ft
Maximum resistance: 20 ohms/1000 ft
Nominal impedance: 100 ~ 140 ohms

Cable Connectors

Cabling must have a male XLR connector on one end and a female XLR connector on the other end.

Do not allow contact between the common and the fixture’s chassis ground. Grounding the
common can cause a ground loop, and your fixture may perform erratically. Test cables with
an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted
to the shield or each other.

5. Appendix 13 11/13/2009 3:17 PM

This drawing
provides a general
illustration of the
DMX input/output
panel of a lighting
fixture.

Universal DMX Controller

Continue the link

3-Pin to 5-Pin Conversion Chart

3-PIN TO 5-PIN CONVERSION CHART

Conductor

3-Pin Female (Output)

5-Pin Male (Input)

Ground/Shield

Pin 1

Pin 1

Data ( - ) signal

Pin 2

Pin 2

Data ( + ) signal

Pin 3

Pin 3

Not used

Pin 4

Not used

Pin 5

If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin
adapter. The chart below details a proper cable conversion:

Setting up a DMX Serial Data Link

1. Connect the (male) 3-pin connector side of
the DMX cable to the output (female) 3-pin
connector of the controller.

2. Connect the end of the cable coming from
the controller which will have a (female)
3-pin connector to the input connector of
the next fixture consisting of a (male) 3-pin
connector.

3. Then, proceed to connect from the output
as stated above to the input of the following
fixture and so on.

5. Appendix 14 11/13/2009 3:17 PM

Setting the Starting Address

SYMPTOM

POSSIBLE CAUSE(S)

POSSIBLE ACTION(S)

Breaker/Fuse

keeps blowing

Excessive circuit load

Check total load placed on the electrical circuit.

Short circuit along the power

wires

Check for a short in the electrical wiring (internal and/or

external).

Device does not

power up

No power

Check for power on Mains.

Loose power cord

Check power cord

Fixture is not

responding to

DMX

Wrong DMX addressing

Check Control Panel and unit addressing

Damaged DMX cables

Check DMX cables

Wrong polarity settings on the

controller

Check polarity switch settings on the controller
Loose DMX cables

Check cable connections

Faulty DMX interface

Replace DMX input

Faulty Main PCB

Replace Main PCB

Loss of signal

Non DMX cables

Use only DMX compatible cables

Bouncing signals

Install terminator as suggested.

Long cable / Low level signal

Install amplifier right after fixture with strong signal.

Too many fixtures

Install an optically coupled DMX splitter after unit #32.

Interference from AC wires

Keep DMX cables separated from power cables or

black lights.

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a start address
from 1~512. A fixture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a fixture that uses six DMX channels and was addressed to start
on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105. Choose start
addresses so that the channels used do not overlap, and note the start address selected for future reference.

If this is your first time addressing a fixture using the DMX control protocol, we suggest jumping to the

“Appendix” section and reading the heading “DMX Primer”. It contains very useful information that will help you

understand its use.

General Troubleshooting

If you still have a problem after trying the above solutions, please contact CHAUVET Technical
Support.

Contact Us

World Wide

5. Appendix 15 11/13/2009 3:17 PM

General Information CHAUVET

Technical Support CHAUVET

World Wide Web www.chauvetlighting.com

3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084

3000 North 29th Court
Hollywood, FL 33020
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)

Returns Procedure

Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued.
Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #).
Products returned without the RMA # will be refused. Call CHAUVET and request an RMA # prior to
shipping the fixture. Be prepared to provide the model number, serial number and a brief description
of the cause for the return. Be sure to pack fixture properly; any shipping damage resulting from

inadequate packaging is the customer’s responsibility. As a suggestion, proper UPS packing or

double-boxing is always a safe method to use.

CHAUVET reserves the right to use its own discretion to repair or replace product(s).

If you are given an RMA #, please include the following information on a piece of paper inside
the box:

1) Your name

2) Your address

3) Your phone number

4) The RMA #

5) A brief description of the symptoms

Claims

Damage incurred in shipping is the responsibility of the shipper; therefore, the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.

5. Appendix 16 11/13/2009 3:17 PM

Technical Specifications

WEIGHT & DIMENSIONS

Length .......................................................................................................................... 8.2 in (208 mm)

Width.......................................................................................................................... 17.3 in (439 mm)

Height ............................................................................................................................. 8 in (203 mm)

Weight.............................................................................................................................. 6 lbs (2.7 kg)

POWER

Autoswitching Power Supply ........................................................................... 100~240 VAC, 50/60 Hz

Power Consumption @ 120 VAC, 60 Hz ...............................................31 W (0.4 A) max, 0.4 A inrush

Power Consumption @ 230 VAC, 50 Hz ...............................................31 W (0.4 A) max, 0.3 A inrush

Power output ..................................................................................................................... 25 units max

Fuse .................................................................................................................................. T 2 A, 250 V

LIGHT SOURCE

LED ........................................................................ 6 (2 red, 2 green, 2 blue) 3 W, 700 mA, 50,000 hrs

PHOTO OPTIC

Coverage Angle .............................................................................................................................. 79°

THERMAL

Maximum ambient temperature ...................................................................................... 104° F (40° C)

ORDERING INFORMATION

Mayhem™............................................................................................................................. MAYHEM

WARRANTY INFORMATION

Warranty ........................................................................................................... 2-year limited warranty

Technical Specifications 17 11/13/2009 3:17 PM