Chauvet ILS-625DCR, ILS-606DBR, ILS-606DSR User Manual

Page 1
ILS
-
606DBR
ILS-606DSR
USER MANUAL
products;
625DCR.
ILS-625DCR
This manual includes instructions and overview on the following 3 CHAUVET
CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
ILS-606DBR, ILS-606DSR and ILS-
2005-03-09/22:45
Page 2
TABLE OF CONTENT
TABLE OF CONTENT ...............................................................................................................................................................2
BEFORE YOU BEGIN................................................................................................................................................................3
WHAT IS INCLUDED ............................................................................................................................................................................................. 3
UNPACKING INSTRUCTIONS.................................................................................................................................................................................. 3
AC POWER ........................................................................................................................................................................................................ 3
SAFETY INSTRUCTIONS ....................................................................................................................................................................................... 3
INTRODUCTION.........................................................................................................................................................................4
FEATURES ......................................................................................................................................................................................................... 4
DMX CHANNEL SUMMARY ................................................................................................................................................................................... 4
WHAT IS ILS? .................................................................................................................................................................................................... 4
PRODUCT OVERVIEW .......................................................................................................................................................................................... 5
SETUP.........................................................................................................................................................................................6
LAMP................................................................................................................................................................................................................. 6
Lamp installation .................................................................................................................................................................................... 6
POWER.............................................................................................................................................................................................................. 6
MOUNTING......................................................................................................................................................................................................... 7
Hanging Bracket & Fixture Floor Stands .................................................................................................................................................. 7
Orientation ............................................................................................................................................................................................. 7
Rigging .................................................................................................................................................................................................. 7
LAMP ALIGNMENT ............................................................................................................................................................................................... 7
Lamp Alignment How-To ........................................................................................................................................................................ 7
OPERATING INSTRUCTIONS..................................................................................................................................................8
MENU NAVIGATION ............................................................................................................................................................................................. 8
OPERATING MODES ............................................................................................................................................................................................ 9
Stand Alone ........................................................................................................................................................................................... 9
Master/Slave .......................................................................................................................................................................................... 9
DMX Mode ............................................................................................................................................................................................. 9
MENU FUNCTIONS .............................................................................................................................................................................................. 9
DMX-512 addressing {Addr} ......................................................................................................................................................................... 9
Setting the starting address .................................................................................................................................................................. 10
Master/Slave settings {SLNd}  {SL 1}
Setting the alternate slave mode {SL 2}................................................................................................................................................. 10
User Configurations {CLNd}, {IPan}, {ItLt}, {Irot}-606DBR, {IdIN} ................................................................................................................. 11
Color Mode {CLNd} .............................................................................................................................................................................. 11
Pan Invert {IPan} – tilt Invert {ItLt} – {Irot}............................................................................................................................................... 11
Segment Display Configurations {Led}, {IdSP}............................................................................................................................................ 11
Turning the Display off {Led}................................................................................................................................................................. 11
Display Inverse {IdSP}.......................................................................................................................................................................... 11
Fixture Test and Service Functions {FAdJ}, {teSt}, {FhrS}, {rSet} ................................................................................................................. 12
Focus Adjustment {FAdJ}...................................................................................................................................................................... 12
Fixture Self-Test {teSt}.......................................................................................................................................................................... 12
Fixture Reset {rSet} .............................................................................................................................................................................. 12
Fixture Hours {FhrS}............................................................................................................................................................................. 12
CA-8 & CA-8F Easy Controller (Optional) ................................................................................................................................................... 13
APPENDIX................................................................................................................................................................................14
DMX PRIMER ................................................................................................................................................................................................... 14
Fixture Linking ...................................................................................................................................................................................... 14
DMX CHANNEL VALUES (606DSR & 606DBR).................................................................................................................................................... 15
DMX CHANNEL VALUES (625DCR) .................................................................................................................................................................... 16
GOBOS............................................................................................................................................................................................................ 17
MAINTENANCE.................................................................................................................................................................................................. 18
RETURNS PROCEDURE...................................................................................................................................................................................... 18
CLAIMS............................................................................................................................................................................................................ 18
GENERAL TROUBLESHOOTING............................................................................................................................................................................ 19
TECHNICAL SPECIFICATIONS .............................................................................................................................................................................. 20
TECHNICAL SUPPORT........................................................................................................................................................................................ 20
{SL 2}........................................................................................................................................ 10
ILS-606 & ILS-625 User Manual 2 2005-03-09/22:45
Page 3
Figure 1 - AC Voltage Switch
BEFORE YOU BEGIN
What is included
One of the following;
ILS-606DBR - Trackscan 250DBR-ILS ILS-606DSR - Trackscan 250DSR-ILS ILS-625DCR - Colortrack 250DCR-ILS
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixtures specifications chart. A fixtures listed current rating is its average current draw under normal conditions. All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the source voltage matches the fixtures requirement. Check the fixture or device carefully to make sure that if a voltage selection switch exists that it is set to the correct line voltage you will use.
Warning! Verify that the power select switch on your unit matches the line voltage applied. All
fixtures must be connected to circuits with a suitable Earth Ground.
Power cord with plug MSD-250 Discharge lamp Removable Floor Stands Warranty Card
Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance?
Please keep this User Guide for future consultation. If you
sell the unit to another user, be sure that they also receive this instruction booklet.
Always make sure that you are connecting to the proper
voltage and that the line voltage you are connecting to is not higher than that stated on decal or rear panel of the fixture.
This product is intended for indoor use only!  To prevent risk of fire or shock, do not expose fixture to
rain or moisture. Make sure there are no flammable materials close to the unit while operating.
The unit must be installed in a location with adequate
ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked.
Always disconnect from power source before servicing or
replacing lamp or fuse and be sure to replace with same lamp source.
Caution! There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET.
Secure fixture to fastening device using a safety chain.
Never carry the fixture solely by its head. Use its carrying handles.
Maximum ambient temperature is Ta: 40°. Do not operate
fixture at temperatures higher than this.
In the event of serious operating problem, stop using the
unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
Dont connect the device to a dimmer pack. Make sure power cord is never crimped or damaged.  Never disconnect power cord by pulling or tugging on the
cord.
Avoid direct eye exposure to lamp while it is on.
ILS-606 & ILS-625 User Manual 3 2005-03-09/22:45
Page 4
INTRODUCTION
Features
7 interchangeable rotating gobos 9 trapezoid cut dichroic colors plus white manual focus mechanical dimming super bright 250 watt discharge lamp, 2000 hour life switch-selectable power settings 115V or 230V, (240V version available) clear digital segment display ILS Integrated Lighting System for advanced pre-programmed functions high efficiency optical system removable fixture floor stand dichroic coated optics
DMX Channel Summary
606DBR & 606DSR 625DCR
CHANNEL FUNCTION CHANNEL FUNCTION
What is ILS?
ILS stands for Integrated Lighting System. CHAUVET fixtures with the ILS logo are equipped with an advanced independent show technology that enables synchronization across all intelligent lighting fixtures within the group. Gobos, colors and chases are among the various features that synchronize. In Master/Slave mode, the first fixture in the chain will automatically address fixtures that follow. In conjunction with the ILS­CON controller, ILS fixtures are also addressed remotely by the controller further reducing the time to setup prior to a show. In short, CHAUVETs ILS fixtures give the user the power and the speed to perform efficiently and effectively in the shortest possible time.
1
606DBR: Barrel rotation
2
3
4
5
6
7
Pan 1 Shutter
606DSR: Tilt
Shutter 3 Color
Gobos 4 Gobo Rotation
Color 5 Dimmer
Gobo Rotation
Dimmer
2 Gobos
ILS-606 & ILS-625 User Manual 4 2005-03-09/22:45
Page 5
Introduction
Figure 2 Product Overview
Product Overview
Carrying
handle
Pan/Tilt Arm
Hanging
Bracket
Removable
Fixture Floor
Stands!
606DSR
LED Segment Display
Scan Mirror
Adjustable
Lens Gun
bolts
Multi-
mirrored
Barrel
606DBR
625DCR Front cover
I/O Panel located on bottom
LED SEGMENT DISPLAY OVERVIEW
LED INDICATORS STATUS FUNCTION
DMX
MASTER
Slave
Sound
BUTTONS I/O PANEL
MENU
DOWN
ENTER
Steps backward through menu
UP
Steps forward through menu
On DMX input is present
On Unit is in the Master operating mode On Unit is in the Slave operating mode
Flashing Sound Active mode is on
SEGMENT BUTTONS I/O PANEL OVERVIEW
Toggles programming
functions
functions
functions
Confirms selected menu
function
DMX Out & In DMX-512 connectors
MIC Built in microphone
Sensitivity POT Sets audio sensitivity
Remote control
Accepts ¼ connector from the CA-8 or CA-8F
Easy Controller providing Stand By, Strobe/Next
and Show1 1/Slow/Show 2 functions.
of fixtures
ILS-606 & ILS-625 User Manual 5 2005-03-09/22:45
Page 6
MIC
CONF IGUR ATION
CH2= TILT R OTATI ON
CH3= SHUT TER/ SHA KING
POWE R
depending on your line voltage.
SETUP
Lamp
You will need to install a lamp prior to the initial operation of the fixture. A MSD250 high intensity discharge lamp is included.
Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the
unit to cool down! Always disconnect from main power prior to lamp replacement.
Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp with alcohol and wipe it with a lint free cloth before installation.
LAMP INSTALLATION
1) Remove both thumbscrews located on the bottom of the fixture.
2) Pull out lamp socket plate as pictured to the right.
3) If replacing the lamp, remove old lamp first.
4) Holding the new lamp by its base, align the small pin on the lamp with the small hole in the socket and insert the lamp squarely until the retaining clips on the lamp socket secures the lamp tightly.
5) Clean the glass/envelope of the bulb with an alcohol wipe or equivalent.
6) Holding the lamp socket plate, insert the tip of the lamp into the fixture with extreme care. Navigate the lamp all the way until it reaches the reflector and the lamp base plate touches the bottom plate of the fixture.
7) Align the screw holes and fasten the thumbscrews back onto the lamp socket plate.
8) If you are replacing the lamp, you may want to log the fixture hours in order to track the lamps use. Navigate to the {FhrS} on the menu display to obtain this information.
9) Turn the fixture on and adjust the lamp alignment screws until the brightest most even area of the beam is in the center of your spot. It may be necessary for you to use a controller in order to command the fixture to display a white beam on a flat surface with no gobos or colors.
ILS-6xx Lamp Installation
Lamp alignment screws
PIN1-C OMM PIN2-D MX ­PIN3-D MX +
OUTP UT
INPUT
Adju st lam p po sitio n by tu rnin g scre ws A ,B an d C.
CH1= PAN
CH4= GOBO CH5= COLO R CH6= GOBO ROTA TION CH7= DIMM ER
Disco nne ct po wer a nd wa it 5 m in. be fore open ing.
Model : Seria l No: Power : Fuse : Bulb :
O NLY FO R REMO TE CO NTRO L
SENS ITIVI TY
Remove both thumbscrews
FUSE
D
C
E
Q
S S
A
P
Power
Your product is equipped with switch-selectable AC power setting.
Warning! Verify that the power select switch on your unit
matches the line voltage applied. All fixtures must be connected to circuits with a suitable Earth Ground.
To determine the power requirements for a particular fixture,
see the label affixed to the back plate of the fixture or refer to the fixtures specifications chart.
A fixtures listed current rating is its average current draw under normal conditions. All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch.
Before applying power to a fixture, check that the source voltage matches the fixtures
requirement.
All fixtures must be connected to circuits with a suitable Earth Ground.
ILS-606 & ILS-625 User Manual 6 2005-03-09/22:45
Slide switch up or down
Page 7
Setup
Hanging Bracket
Clamp is sold separately.
MIC
CONFI GURAT ION
CH2=TI LT ROT ATION
CH3=S HUTTE R/SH AKIN G
POWER
Mounting
HANGING BRACKET & FIXTURE FLOOR STANDS
Mount the hanging bracket on the fixture as illustrated on the right. The tension knob is unique in that it is self ratcheting, providing you tool-free tensioning of the bracket. Pull knob handle towards you and turn either to apply tension or to release tension. Also included are two fixture floor stands and a convenient hex wrench tool for fastening them. The wrench also opens the fixtures front and back covers.
ORIENTATION
This fixture may be mounted in any position provided there is adequate room for ventilation. It is also possible to stand this fixture using the removable floor stands.
RIGGING
It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable C or O type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs.
When selecting installation location, take into consideration lamp
replacement access and routine maintenance.
Safety cables should always be used. Never mount in places where the fixture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.
Note!
Lamp Alignment
LAMP ALIGNMENT HOW-TO
Often, after a new installation of a lamp, you will find that there is an uneven field of light or what is referred to as a hot spot. This is due to the most intense point of the lamp source not being positioned optimally within the reflector. There are three lamp alignment screws provided at the base of the fixture. Turning these screws allow you to optimize the projection quality of the spot as well as the overall intensity of the beam.
1) Project a white spot against any flat surface. Preferably the surface should be white or pastel in color.
2) Turning the lamp alignment screws, try to position the hot spot in the center of the beam as best as possible. This could require many attempts on your part. It is advisable to even out the screws prior to lamp alignment as described in the illustration.
3) Once the hot spot is in the center of the spot, do your best to turn all screws equally as to affect movement up or down within the reflector.
4) As you move in and out of optimum lamp focus, you will see the hot spot either get wider or narrower. The goal is to either totally diminish the hot spot by having it widen and spread across the entire spot or moving the hot spot so that it covers as much of the beam spot area as possible.
Lamp alignment screws
PIN1-CO MM PIN2-DM X ­PIN3-DM X +
OUTPUT
INPUT
Adjust lamp po sition by turnin g scre ws A,B and C.
SENSI TIVITY ONLY FOR
Even out this plate by turning the
REMOTE C ONTROL
lamp alignment screws, prior to
CH1=PA N
CH4=G OBO
lamp optimization. This will
CH5=C OLOR CH6=G OBO R OTATIO N CH7=D IMMER
provide you a good starting point.
Disco nnect po wer an d wait 5 m in. befo re open ing.
Model : Serial No: Power : Fuse: Bulb:
FUSE
D
C
E
Q
S
S A P
ILS-606 & ILS-625 User Manual 7 2005-03-09/22:45
Page 8
OPERATING INSTRUCTIONS
Menu Navigation
To select any of the pre-set functions, press the MENU button until the desired function is shown on the display. Select the function by pressing the ENTER button and the display will blink. Use the DOWN and UP button to change the settings. Once the required setting has been selected, press the ENTER button to activate it. If you don not press the ENTER button, it will automatically return to the main functions without any change after idling 8 seconds. To go back to the functions without any change press the MENU button. The main functions are shown below:
MENU
DMX-512 Address Setting
Addr
SLNd
bLNd
CLNd
IPan
ItLt (606DSR)
or
Irot (606DBR)
LEd
IdSP
IdIN
FAdJ
Focus adjust
test
Self test
FhrS
Fixture hours
rSeT
Reset
1 ~ 512
Slave mode 2 Light Show
Blackout mode No to blackout
Blackout mode Yes to Blackout
606DBR - Barrel Rotation Normal
606DBR – Barrel Rotation Inverse
SL 2
SL I
Slave mode Normal
N bo
Y bo
SC
Split Color
No
Normal Color
I
Pan Inverse
No
Pan Normal
606DSR - Tilt Normal
606DSR – Tilt Inverse
I
No
ON
Display On
OFF
Display Off
dSPI
Display Normal
IdSP
Display Inverse
I
Dimmer Inverse
No
Dimmer Normal
Figure 3 - Display Panel Diagram
Upon powering up the unit, you will notice that it will display a fixture ID. In addition, the fixtures electronics will load up its programming and home (adjust) its motors to a starting position. The sequence of events
ILS-606 & ILS-625 User Manual 8 2005-03-09/22:45
Page 9
Operating Instructions
Optional
Daisy Chain
Connection
should take no more than 20 seconds and it is necessary for the fixture to operate correctly. During this time you will hear motor and mechanical movement inside the fixture. After this initial power-up sequence, if the fixture receives no DMX signal, it will enter into a stand alone mode. Be sure to power up your DMX controller device before the lighting fixture to avoid unwanted auto mode operation.
Operating Modes
All models can be operated in three different ways.
A stand-alone mode will listen to sound and run through its diverse range of built in programs. Master/Slave mode will allow the command of up to as many units you want in a synchronized
light show to the sound.
DMX control mode will provide the greatest flexibility and creativity. Each fixture trait can be
controlled individually using any universal DMX-512 controller.
STAND ALONE
The Stand Alone mode is activated automatically when the fixture is absent of DMX signal or a controller is not connected. All models will run through their built in programs as they listen to the sound.
MASTER/SLAVE
The Master/Slave mode will allow you to link multiple units in a daisy chain fashion. In this mode, the first unit in the daisy chain will automatically command all other units following. The ILS system provides for the synchronization of all CHAUVET products whose model number is pre-fixed by the letters ILS. Master/Slave operation does not require any menu or setting selections. Simply connect each fixture in a daisy like fashion using qualified 3 pin DMX cables as described below. The first unit in the chain will operate in a Stand/Alone mode and all units following will synchronize to the first unit.
1) Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture.
2) Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on as illustrated below in Daisy Chain Connection.
DMX MODE
Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to customizing or creating a show. You can tailor your programming to suit a specific event. Whether it is a wedding where a spot light may be required or a lead singer requiring a color solo, the opportunities are endless. In this mode you will be able to control each individual trait of the fixture independently.
Menu Functions
DMX-512 addressing {Addr}
This mode enables the use of a universal DMX controller device. Each fixture requires a "start address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and
ILS-606 & ILS-625 User Manual 9 2005-03-09/22:45
Page 10
Operating Instructions
105. Choose start addresses so that the channels used do not overlap and notate the start address
selected for future reference. If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping to the Appendix Section and read the heading DMX Primer. It contains very useful information that will help you understand its use.
FIXTURE DMX CHANNELS NOTES
ILS-606DSR
ILS-606DBR
ILS-625DCR
7
7
5
When calculating the next starting address for a particular fixture, simply add the number of channels used by the last fixture to the starting address of the last fixture. The result is the starting address of the next fixture. Example: Fixture # 1 Uses 7 Channels, Set to DMX 001 Add 7 to the previous start address 007 + Fixture # 2 Uses 6 Channels, Set to DMX 008 Total Add 6 to the previous start address 006 + Fixture # 3 Uses 4 Channels, set to DMX 014 Total
Caution! Some controllers are factory configured to control a specific range of channels per
fixture. For example, you may have a controller pre-set to control 10 channels per fixture for a total of 12 fixtures. In this case you would be required to separate all fixtures in 10 channel increments instead of the true number of channels your particular fixture utilizes.
SETTING THE STARTING ADDRESS
1) Press the MENU button until the display reads {Addr}.
2) Press the ENTER button to select DMX addressing. Once selected the display will read either a 1 or any other number that may have previously been set. You must make a selection within 6 seconds.
3) Press the UP and DOWN buttons to increase or decrease values until the desired value is achieved.
4) Press the ENTER button to activate selection.
Master/Slave settings {SLNd}  {SL 1}  {SL 2}
By linking the units under a master/slave control mode, the first unit can direct additional units to create a sound activated, synchronized light show. This is very useful for mobile DJs who want to setup and run a show quickly. In this mode the fixture is assigned a master status and is indicated by the MASTER LED. If the fixture is not connected to a controller then it will automatically enter a sound activated state. You can adjust the microphone sensitivity pot on the fixture for optimum sound recognition. Any other units connected will automatically be assigned to {SL 1} mode, which is the standard Slave mode providing unison synchronized movements and gobo-color changes.
SETTING THE ALTERNATE SLAVE MODE {SL 2}
Unlike {SL 1}, {SL 2} enhances the pre-programmed shows by contrasting the movements. Once you select this mode, the fixture will remember it the next time your power up.
1) Tap the MENU button until the display reads {SLNd}.
2) Press the ENTER button to select this function. The selection is confirmed when the display begins to blink. You must make a selection within 8 seconds.
3) Press the UP and DOWN buttons to toggle between the Slave Shows available. Note! There are 4 shows available in Model # ILS-625DCR and 2 shows in the rest.
4) Press the ENTER button to activate selection.
ILS-606 & ILS-625 User Manual 10 2005-03-09/22:45
Page 11
Operating Instructions
User Configurations {CLNd}, {IPan}, {ItLt}, {Irot}-606DBR, {IdIN}
All of the fixtures have three user selectable run-time configurations that change the behavior of a certain function. The three functions are described below.
COLOR MODE {CLND}
This mode allows you to select whether your controller will access the color palettes in solid colors only or solid and split colors.
1) Tap the MENU button until the display reads {CLNd}.
2) Press the ENTER button to select this function. The selection is confirmed when the display begins to blink. You must make a selection within 8 seconds.
3) Press the UP and DOWN buttons to toggle between the {SC} for split colors and {no} for no split colors.
4) Press the ENTER button to activate selection.
PAN INVERT {IPAN} – TILT INVERT {ITLT} – {IROT}
It is possible to invert the pan and tilt mirror movement from within the fixture itself. This could be helpful in situations where the positioning or rigging of a fixture led to a reverse orientation of the fixture in relation to all or most other fixtures installed. When choosing to command the pan or tilt of all fixtures at the same time you will notice that the fixtures whose orientation is different from the others will most likely move opposite of the rest. You can apply a pan and tilt Invert by following these instructions.
1) Tap the MENU button until the display reads {IPan} or {ItLt}.
2) Press the ENTER button to select this function. The selection is confirmed when the display begins to blink. You must make a selection within 8 seconds.
3) Press the UP and DOWN buttons to toggle between the {I} for inverse and {no} for none.
4) Press the ENTER button to activate selection.
5) Note! For the 606DBR Barrel Scan, the {ItLt} function is replaced with {Irot} which reverses the rotation of the Barrel mirror instead.
Segment Display Configurations {Led}, {IdSP}
The LED segment display can be set to off after 8 seconds of no menu activity. The LED will display again as soon as the menu is accessed by pressing any of the buttons. The display can also be inverted making it easier to read the menu depending on the orientation of your fixture.
TURNING THE DISPLAY OFF {LED}
1) Tap the MENU button until the display reads {Led}.
2) Press the ENTER button to select this function. The selection is confirmed when the display begins to blink. You must make a selection within 8 seconds.
3) Press the UP and DOWN buttons to toggle between the {on} and {off} setting.
4) Press the ENTER button to activate selection.
5) Note! This configuration is set on an individual fixture basis.
DISPLAY INVERSE {IDSP}
1) Tap the MENU button until the display reads {IdSP}.
2) Unlike in other instructions, pressing the ENTER button will toggle between { IdSP} for normal and {dSPI} for reversed.
ILS-606 & ILS-625 User Manual 11 2005-03-09/22:45
Page 12
Operating Instructions
3) Press the MENU button to confirm or leave alone for 8 seconds.
Fixture Test and Service Functions {FAdJ}, {teSt}, {FhrS}, {rSet}
FOCUS ADJUSTMENT {FADJ}
The focus adjustment tool activates a pre-set program that turns the lamp on and projects a gobo image so that you can manually adjust the focus.
1) Tap the MENU button until the display reads {FAdJ}.
2) Press ENTER and the display will blink.
3) Adjust the focus by rotating the lens gun in the direction that brings the image into focus.
4) Press the MENU button to leave this mode.
FIXTURE SELF-TEST {TEST}
The test sequence will run through all of the projection capabilities of each individual fixture, including gobo and color effects.
1) Tap the MENU button until the display reads {teSt}.
2) Press ENTER and the fixture will immediately begin to play back a test sequence. Observe tentatively for any abnormalities.
3) Press the MENU button to leave this mode.
FIXTURE RESET {RSET}
This function will re-initialize the fixture by returning all motors to its startup positions or otherwise known as (home position).
1) Tap the MENU button until the display reads {rSet} and press ENTER.
FIXTURE HOURS {FHRS}
The (fixture hours) readout displays the number of hours the fixture has been in use. It is not uncommon to find new fixtures with a few logged hours. This means the fixture was thoroughly tested prior to delivery.
1) Tap the MENU button until the display reads {FhrS}.
2) Press ENTER to view the total working hours.
3) You can leave alone and the display will return to the regular menu or press MENU button to return to main menu.
ILS-606 & ILS-625 User Manual 12 2005-03-09/22:45
Page 13
CA-8 & CA-8F Easy Controller (Optional)
CA-8 Easy Controller & the
X/Y Moving Patterns for CA
-
8 Controller
The CA-8 Easy Controller is used only in master/slave mode. Connect the controller to the 1/4 microphone jack in the first unit. The table below describes the different preset shows the CA-8 Controller can command.
CA-8 & CA-8F BUTTONS
STAND BY MODE FUNCTION
Fixture: All
Strobe
1. Gobo/color sync strobe
2. sync strobe
3. two light strobe Fixture: 606DBR & 606DSR
(X/Y) moving patterns (12 patterns user selectable)
Fixture: 625DCR Chase Pattern selection (6 patterns)
Fixture: All Color/Gobo selection (Hold for gobo change, tap for color change.)
Fixture: 606DBR & 606DSR X/Y moving position, dimmer setting
Fixture: 625DCR Dimmer setting
BLACKOUT
(LED off)
Sound
(LED blinks normal)
Sound
(LED on)
Slow/Sound
(LED blinks fast)
Position
CA-8F Foot Controller
Note! All programmed movements are built into the fixtures and are triggered by the CA-8(F) controllers.
ILS-606 & ILS-625 User Manual 13 2005-03-09/22:45
Page 14
APPENDIX
COMMON
DMX +
DMX -
1 3 2 1 3 2 1 3 2
Termination reduces signal errors and to
DMX Primer
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A fixture capable of receiving DMX-512 will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller. There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required. Choosing a start address should be planned in advance. Channels should never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is set incorrectly. You can however, control multiple fixtures of the same type using the same starting address as long as the intended result is that of unison movement or operation. In other words, the fixtures will be slaved together and all respond exactly the same. DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the fixtures are connected is not important and has no effect on how a controller communicates to each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33), DMX-4.5 (15) and DMX-1.5 (5’)
Figure 4 - DMX connector configuration
INPUT
OUTPUT
avoid signal transmission problems and
interference, it is always advisable to
connect a DMX signal terminator.
Resistance 120 ohm 1/4w between pin 2 (DMX -) and pin 3 (DMX +) of the last fixture.
FIXTURE LINKING
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5
pin to 3 pin adapter. CHAUVET Model No: DMX5M. The chart below details a proper cable conversion:
3 PIN TO 5 PIN CONVERSION CHART
Conductor
Ground/Shield
Data ( - )signal
Data ( + ) signal
3 Pin Female (output) 5 Pin Male (Input)
Pin 1 Pin 1
Pin 2 Pin 2
Pin 3 Pin 3
Do not use
Do not use
ILS-606 & ILS-625 User Manual 14 2005-03-09/22:45
Do not use
Do not use
Page 15
Appendix
DMX Channel Values (606DSR & 606DBR)
CHANNEL VALUE FUNCTION
1
2
3
000 255
000 255
000 009 010 120 121 134 135 245 246 255
000 007 008 015 016 131 132 247 248 255
Pan Left > Right ( 128 = center)
Tilt 606DSR Up > Down (128 = center)
Barrel Rotation - 606DBR Stopped Fast > Slow (counter-clockwise) Stopped Slow > Fast (clockwise) Stopped
Shutter/Shaking Blackout Open Slow > Fast (shutter) Slow > Fast (shaking) Open
000 015 016 031 032 047
4
5
6
7
048 063 064 079 080 095 096 111 112 127 128 255
(normal) 000 012 013 025 026 038 039 051 052 063 064 076 077 089 090 102 103 115 116 127 128 255
000 009 010 120 121 134 135 245 246 255
000 255
000 007 008 015 016 022 023 030 031 037 038 045 046 052 053 060 061 067 068 075 076 082 083 090 091 097 098 105 106 112 113 120 121 127 128 255
(CS)
Gobo Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Slow > Fast (gobo scroll)
Color (normal) Open (white) Green Magenta Light Blue Yellow Orange Blue UV Purple Light Green Pink Slow > Fast (color scroll)
Gobo rotation
Stopped Fast > Slow (counter clockwise) Stopped Slow > Fast (clockwise) Stopped
Dimmer
Open > Close
CS (color split mode)
Open (white) Green Green + Magenta Magenta Magenta + Light Blue Light Blue Light Blue + Yellow Yellow Yellow + Orange Orange Orange + Blue Blue Blue + UV Purple UV Purple UV Purple + Light Green Light Green Pink Slow > Fast (color scroll)
ILS-606 & ILS-625 User Manual 15 2005-03-09/22:45
Page 16
Appendix
DMX Channel Values (625DCR)
CHANNEL VALUE FUNCTION
000 007
1
008 015 016 131 132 247 248 255
Shutter/Shaking Blackout Open Slow > Fast (shutter) Slow > Fast (shaking) Open
000 015 016 031 032 047
2
3
4
5
048 063 064 079 080 095 096 111 112 127 128 255
(normal) 000 012 013 025 026 038 039 051 052 063 064 076 077 089 090 102 103 115 116 127 128 255
000 009 010 120 121 134 135 245 246 255
000 255
000 007 008 015 016 022 023 030 031 037 038 045 046 052 053 060 061 067 068 075 076 082 083 090 091 097 098 105 106 112 113 120 121 127 128 255
(CS)
Gobo Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Slow > Fast (gobo scroll)
Color (normal) Open (white) Green Magenta Light Blue Yellow Orange Blue UV Purple Light Green Pink Slow > Fast (color scroll)
Gobo rotation
Stopped Fast > Slow (counter clockwise) Stopped Slow > Fast (clockwise) Stopped
Dimmer
Open > Close (100% - 0%)
CS (color split mode)
Open (white) Green Green + Magenta Magenta Magenta + Light Blue Light Blue Light Blue + Yellow Yellow Yellow + Orange Orange Orange + Blue Blue Blue + UV Purple UV Purple UV Purple + Light Green Light Green Pink Slow > Fast (color scroll)
ILS-606 & ILS-625 User Manual 16 2005-03-09/22:45
Page 17
Gobos
606DBR & 606DSR
Open Dots Tunnel Broken Glass Swirl Cylinder Frost Breakup Triangle 4 Dots
625-DCR
Open Dots Tunnel Broken Glass Frost Cylinder Frost Breakup 3200°K 6600°K
ILS-606 & ILS-625 User Manual 17 2005-03-09/22:45
Page 18
Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components. Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or becomes dirty, clean the lamps with an alcohol wipe. The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the units optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the customers responsibility. CHAUVET reserves the right to use its own discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim for items such as missing component/part, damage not related to shipping, and concealed damage, must be made within seven (7) days of receiving merchandise.
ILS-606 & ILS-625 User Manual 18 2005-03-09/22:45
Page 19
Appendix
General Troubleshooting
Applies to
Symptom Solution(s)
Auto shut off Check fan thermal switch reset Beam is very dim or not
bright Breaker/Fuse keeps
Clean optical system or replace lamp Check 220/110v switch for proper setting
Check total load placed on device
blowing Chase is too slow Check users manual for speed adjustment
Device has no power Check for power on Mains.
Check devices fuse. (internal and/or external)
Fixture is not responding Check DMX Dip switch settings for correct addressing
Check DMX cables Check polarity switch settings
Fixture is on but there is no movement to the audio
Make sure you have the correct audio mode on the control switches. If audio provided via ¼ jack, make sure a live audio signal exists Adjust sound sensitivity knob
Lamps cuts off sporadically
Light will not come on after power failure
Possible bad lamp or fixture is overheating. Lamp may be at end of its life.
Some discharge lamps require a cooling off period before the electronics in the fixture can kick start it again, wait 5 to 10 minutes before powering up
Loss of signal Use only DMX cables
Install terminator Note: Keep DMX cables separated from power cables or black lights.
Motor movements are jerky or jumpy
Possible bad motor driver or sensors Check polarity switch on controller
Moves slow Check 220/110v switch for proper setting No flash Re-install bulb, may have shifted in shipping No light output Check slip ring & brushes for contact
Install bulb Call service technician
Relay will not work Check reset switch
Check cable connections
Remote does not work Make sure connector is firmly connected to device
Foggers
& Snow
Lights
Controllers
Dimmers & Chaser
Stand alone mode All CHAUVET lighting fixtures featuring stand-alone functions
do not require additional settings, simply power the fixture and it will automatically enter into this mode
Unit wobbles when
Check for damages possibly incurred during shipping
rotating
ILS-606 & ILS-625 User Manual 19 2005-03-09/22:45
Page 20
Appendix
Technical Specifications
WEIGHT & DIMENSIONS
(ILS-606DBR, ILS-606DSR).......................................................................................................................
Length ............................................................................................................................695 mm (27.36 in)
Width..............................................................................................................................340 mm (13.39 in)
Height...............................................................................................................................250 mm (9.84 in)
Weight................................................................................................................................15.4 Kg (34 lbs)
(ILS-625DCR)..............................................................................................................................................
Length ..............................................................................................................................360 mm (14.2 in)
Width................................................................................................................................340 mm (13.4 in)
Height.................................................................................................................................250 mm (9.8 in)
Weight................................................................................................................................13.2 Kg (29 lbs)
POWER
Switch-selectable power settings....................................................................115V 60 Hz or 230V 50 Hz
AC input ...............................................................................................................3 prongs IEC 60320 C14
European version......................................................................................................................240V 50 Hz
LAMPS
CHAUVET US-HSD-250........................................................................................2000 hr, 6000K, 250W
Philips MSD-250/2..................................................................................................2000 hr, 6500K, 250W
Philips MSD-200.....................................................................................................2000 hr, 5600K, 200W
GOBOS
Outside diameter ...........................................................................................................................26.8 mm
Image diameter..............................................................................................................................21.0 mm
Thickness.........................................................................................................................................0.2 mm
PHOTO OPTIC
Beam Angle ............................................................................................................................................14°
Pan (ILS-606)........................................................................................................................................180°
Tilt (ILS-606) ...........................................................................................................................................70°
THERMAL
Maximum ambient temperature ..............................................................................................40° (104° F)
FUSE
Main.................................................................................................................20mm Glass 10A Fast Blow
CONTROL & PROGRAMMING
Data input....................................................................................................locking 3-pin XLR male socket
Data output .............................................................................................locking 3-pin XLR female socket
Data pin configuration.................................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols...........................................................................................................................DMX-512 USITT
DMX Channels (606xxx) ...........................................................................................................................7
DMX Channels (625DCR) .........................................................................................................................5
ORDERING INFORMATION
Trackscan 250DBR-ILS Barrel Scanner .............................................................................ILS-606DBR
Trackscan 250DSR-ILS Mirror Scanner .............................................................................ILS-606DSR
Colortrack 250DCR-ILS Color Changer.............................................................................ILS-625DCR
Fuse 10A 250V....................................................................................................................P170FUSE010
OPTIONS
Easy Controller ....................................................................................................................................CA-8
Easy Foot Controller..........................................................................................................................CA-8F
Technical Support
Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.) Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Press 4) Fax: (954) 929-5560 - (Attention: Service)
ILS-606 & ILS-625 User Manual 20 2005-03-09/22:45
Website: http://www.chauvetlighting.com
Loading...