Page 1
User Manual
Page 2
TABLE OF CONTENTS
1. Before You Begin .......................................................................................................... 3
What is Included ............................................................................................................................... 3
Unpacking Instructions ..................................................................................................................... 3
Claims ....................................................................................................................................................... 3
Text Conventions ............................................................................................................................. 3
Symbols ............................................................................................................................................ 3
Disclaimer ......................................................................................................................................... 3
Product at a Glance .......................................................................................................................... 3
Safety Notes ..................................................................................................................................... 4
2. Introduction ................................................................................................................... 5
Overview ........................................................................................................................................... 5
Dimensions ....................................................................................................................................... 6
3. Setup .............................................................................................................................. 7
AC Power ......................................................................................................................................... 7
Fuse Replacement .................................................................................................................................... 7
Mounting ........................................................................................................................................... 8
Orientation ................................................................................................................................................. 8
Rigging ...................................................................................................................................................... 8
Tank Inversion Steps for Inverted Mounting .................................................................................. 11
4. Operation ......................................................................................................................12
Control Panel Operation ................................................................................................................. 12
Menu Map ....................................................................................................................................... 12
DMX Personality and Starting Address ................................................................................................... 12
DMX Linking ................................................................................................................................... 12
Configuration (DMX) ................................................................................................................................ 12
Configuration (Standalone) ............................................................................................................ 14
Programmable Color Selection <MANUAL> ............................................................................................ 14
Programmable Color Selection (Wireless Remote Control) ..................................................................... 14
Wireless Remote Control ......................................................................................................................... 14
5. Technical Information ..................................................................................................15
Fogger Maintenance ...................................................................................................................... 15
Storage/ Maintenance .................................................................................................................... 15
General Troubleshooting ................................................................................................................ 16
6. Technical Specifications ..............................................................................................17
Returns ........................................................................................................................................... 18
Contact Us .........................................................................................................................19
Page 2 of 19 Geyser P4. User Manual Rev. 2
Page 3
What is
Unpacking
Instructions
Carefully unpack the product immediately and check the container to make sure all the
If the box or the contents (the product and included accessories) appear damaged from
.
Failure to report damage to the carrier immediately may invalidate your claim. In
For other issues, such as missing components or parts, damage not related to shipping,
Text
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Critical installation, configuration, or operation information. Not
damage to the product, or cause harm to the operator.
Disclaimer
Chauvet believes that the inform ation contained in this m anual is accurate in all respects. However,
omissions in this document, whether such errors or
omissions resul t from negligenc e, accident or any other cause. Chauvet reserves the ri ght to revise the
content of this document without any obligation to notify any person or company of such revision,
ever, Chauvet has no obligation to make, and does not commit to make, any such revisions.
Product at a
x
P
x
P
x
P
DMX
x
User-Serviceable
x
x
1. BEFORE YOU BEGIN
Included
Claims
Conventions
• Geyser P4
• Geyser Wireless Remote Control
• Geyser Wired Remote Receiver
parts are in the package and are in good condition.
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet
addition, keep the box and contents for inspection.
or concealed damage; file a claim with within 7 days of delivery.
Convention Meaning
Symbol Meaning
• Power Cord
• Warranty Card
• Quick Reference Guide
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or
how
Download the latest version from www.chauvetlighting.com.
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2016 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, Geyser P4 and Geyser are registered trademarks or trademarks of Chauvet &
Sons LLC. (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company
and product names and logos referred to herein may be trademarks of their respective companies.
Glance
Use on Dimmer
Outdoor Use
Sound-Activated
Master/Slave
following these instructions may make the product not work, cause
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Geyser P4 User Manual Rev. 2 Page 3 of 19
Auto Programs
Fixed voltage (120 V or 230 V)
Replaceable Fuse
Page 4
Safety Notes
mounting, usage, and maintenance
Do not add perfume, alcohol, gasoline, or any other flammables to the fog fluid.
completely disconnect the product from power via breaker or by unplugging it.
to
Geyser
to
was specifically designed for use with CHAUVET® Quick Dissipating
Fluid (QDF). For optimum performance with your fogger, Chauvet recommends using
These notes include important information about the
of this product; read before using the product.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing
the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening device using a
safety cable.
• Make sure there are no flammable materials close to the product when operating.
• Do not touch the product’s housing when operating because it may be very hot.
• Do not mount the product on a flammable surface (linoleum, carpet, wood, paper,
carton, plastic, etc.).
• The product’s nozzle is very hot during operation and it remains hot for a long time
after operation has stopped.
• The fog exits the nozzle at a very high temperature. Keep a minimum distance of
6.5 ft (2 m) from the nozzle to the nearest object.
• Do not use the product as a space heater .
• Do not drink or become in contact with the fog fluid. If you do, call your local
emergency service (911 in the US) for help.
•
• Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
• Always install the product in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surface s.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Make sure there is adequate fog fluid in the machine to prevent pump and heater
damage.
• Never connect the product to a dimmer.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product by the power cord or any moving part. Always use the
handles.
• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
• This product is not intended for permanent installation.
• Use only CHAUVET® water-based fog fluid.
• Drain the tank before transporting the product.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
Keep this User Manual for future use. If you sel l the product to another user, be sure
give this document to the next owner.
Fog Cleaner Quart (FCQ) was specifically developed by Chauvet to clean your
P4 Make sure you use FCQ regularly, no longer than 90 days between cleanings,
increase the life of your fogger.
The Geyser P4
QDF.
Page 4 of 19 Geyser P4. User Manual Rev. 2
Page 5
2. INTRODUCTION
Overview
Control
Buttons
Fluid Tank
On/Off Switch
Safety Eye
Remote Control
Receiver Port
Manual Fog
Safety Eye
Handles
Fluid Line In
Nozzle and LEDs
Geyser P4 User Manual Rev. 2 Page 5 of 19
Loop
Power In
Fuse Holder
LED Display
DMX In/Out
Loop
Button
Page 6
Dimensions
2.39 in
(60.8 mm)
13.4 in
(340 mm)
10.2 in
(260 mm)
7 in
(180 mm)
Page 6 of 19 Geyser P4. User Manual Rev. 2
Page 7
AC Power
voltage power supply and it can work with an input voltage of
circuit breaker, power outlet, and
’s panel, or refer to
(circuit breaker or fuse). Make
has an appropriate electrical ground to avoid the risk of
to a rheostat (variable resistor) or dimmer circuit, even
Fuse
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap
3. SETUP
The Geyser P4 has a fixed
either 120 VAC, 60 Hz or 230 VAC, 50 Hz, depending on the specific model.
To determine the product’s power requirements (
wiring), use the current value listed on the label affixed to the product
the product’s specifications chart. The listed current rating indicates the product’s
average current draw under normal conditions.
Always connect the product to a protected circuit
sure the product
electrocution or fire.
Never connect the product
if the rheostat or dimmer channel serves only as a 0–100% switch.
Replacement
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
A spare fuse is not included; however, the safety cap has room for a spare.
Always replace a blown fuse with another of the same type and rating.
Geyser P4 User Manual Rev. 2 Page 7 of 19
Page 8
Mounting
, read and follow the safety recommendations indicated in
Fluid Tank
To avoid spillage with any mounting, always position the fluid tank with the tank’s
Before mounting the product
the Safety Notes.
Orientation
Rigging
Position
Primarily, the Geyser P4 is to be floor mounted in a vertical fog jet orientation.
Alternatively, it may also be mounted in a floor mounting/horizontal fog jet orientation or
in an overhead mounting/downward fog jet orientation; however, be sure to follow
instructions closely to avoid tank spills with alternate mount i n gs.
• Before deciding on a location, always make sure there is easy access to the product
for maintenance and fluid replenishment.
• Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications
).
• When mounting the product overhead, always use a safety cable. Mount the
product securely to a rigging point, such as an elevated platform or a truss.
• When rigging the product onto a truss, you should use mounting clamps of
appropriate weight capacity. Two threaded mounting holes (size M12) are on the
bottom of the product, which are appropriate for this purpose.
• The rubber feet also serve as floor supports. When mounting the product on the
floor, make sure that the product and cables are away from people and vehicles.
Fluid Line
Vertical Fog Jet
Horizontal Fog Jet
cap in the uppermost position above the tank’s fluid line.
When mounting the Geyser P4 in any inverted position, remove the fluid tank from
the holder and set it upright on an adjacent surface.
Page 8 of 19 Geyser P4. User Manual Rev. 2
Page 9
The dimensions shown for the mounting hole positions are included here to aid in
(216 mm)
(
Bottom Panel View
Threaded Mounting Holes
size M12
Bottom of Product
8.5 in
7 in
178 mm)
installation.
Floor Mounting
Floor Mounting – Vertical Fog Output
Geyser P4 User Manual Rev. 2 Page 9 of 19
Floor Mounting – Horizontal Fog Output
Page 10
With inverted mounting, avoid spillage of the fog fluid by setting the fluid tank in
and the
fluid tank when rigging in this manner.
.
or
(or other elevat ed
The Fluid Tank
Overhead Mounting – Downward F og Jet
Alternate Inverted
Truss Mounting
TRUSST®
platform or truss)
Mounting Clamps
(works with CLP-15
CLP-15N clamp from
Chauvet)
Safety Cable for
the Fluid Tank
in an upright
Safety Cable
position
an upright position. Be sure to use a safety cable for both the Geyser P4
Page 10 of 19 Geyser P4. User Manual Rev. 2
Page 11
Tank Inversion Steps for Inverted Mounting
Removable
Plate
1. Empty the fluid from the product.
2. Remove the screws and the bottle lock to take out the tank.
Bottle Lock
3. Turn the fog machine upside down, remove the screws and set aside to take off the
removable plate.
4. Attach the removable plate to the opposite side and secure the tank with the bottle
lock.
5. Secure both the bottom plate and tank cover with the screws.
*Actual product may vary slightly from photo
Geyser P4 User Manual Rev. 2 Page 11 of 19
Page 12
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
Button
Function
<DOWN>
Menu Map
P 0
4 trigger the options set in the
DMX Personality
Starting
When selecting a starting DMX address, always consider the number of DMX channels
CH DMX mode, which defines the
If you are not familiar with the DMX protocol, download the DMX Primer from
DMX Linking
Configuration
4. OPERATION
display.
<MENU>
<UP>
<ENTER>
Mode Programming Steps Description
DMX
Manual Color
Program
Selects an operation mode or to backs out of the current menu option
Scrolls up the list of options or selects a higher value
Scrolls down the list of options or selects a lower value
Activates a menu option or a selected value
Addr d_ _1–d 503
nCoL
(blackout)
P1 –P32
Selects DMX starting Address
Color program off (default) for
<MANUAL> button
Selects preset colors for <MANUAL>
button
Wireless Color
Program
Temperature
Gauge
The Geyser P4 Wireless Remote Control buttons 1–
color programs CH-1–CH-4, respectively.
and
Address
(DMX)
the selected DMX mode uses. If you choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Geyser P4 uses up to 10 DMX channels in a 10
highest configurable address to 503.
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU> repeatedly until Addr shows on the display.
2. Press <ENTER> and d 1–503 will show on the display.
3. Use <UP> or <DOWN> to select the starting address.
4. Press <ENTER>.
The Geyser P4 works with a DMX controller. Information about DMX is in the CHAUVET
DMX Primer, which is available from the Chauvet website
http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf
Set the product in DMX mode (Addr) to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
CH-1 –
CH-4
Ht T _ _ _
P1-1–P1-32
Selects preset color program for wireless
remote operation
Shows current temperature of product
.
Page 12 of 19 Geyser P4. User Manual Rev. 2
Page 13
DMX Channel Assignments and V alues
Channel
Function
Value
Percent/Setting
000 ó 002
No function
003 ó 255
Fog output On
000 ó 002
No function
003 ó 255
0–100%
000 ó 002
No function
003 ó 255
0–100%
000 ó 002
No function
003 ó 255
0–100%
000 ó 002
No function
003 ó 255
0–100%
000 ó 002
No function
003 ó 255
0–100%
000 ó 009
No function
010 ó 017
Color Macro 1
018 ó 025
Color Macro 2
026 ó 033
Color Macro 3
034 ó 041
Color Macro 4
042 ó 049
Color Macro 5
050 ó 057
Color Macro 6
058 ó 065
Color Macro 7
066 ó 073
Color Macro 8
074 ó 081
Color Macro 9
082 ó 089
Color Macro 10
090 ó 097
Color Macro 11
098 ó 105
Color Macro 12
106 ó 113
Color Macro 13
114 ó 121
Color Macro 14
122 ó 129
Color Macro 15
130 ó 137
Color Macro 16
138 ó 145
Color Macro 17
146 ó 153
Color Macro 18
154 ó 161
Color Macro 19
162 ó 169
Color Macro 20
170 ó 177
Color Macro 21
178 ó 185
Color Macro 22
186 ó 193
Color Macro 23
194 ó 201
Color Macro 24
202 ó 209
Color Macro 25
210 ó 217
No Function
218 ó 225
Color Macro 26
226 ó 233
Color Macro 27
234 ó 241
Color Macro 28
242 ó 249
Color Macro 29
000 ó 009
No function
010 ó 255
Speed, slow to fast
000 ó 009
No function
010 ó 255
Strobe, slow to fast
000 ó 002
No function
003 ó 255
0–100%
10CH
1
Fog
2
Red
3
Green
4
Blue
5
Amber
6
UV
7
Color Macros
8
Color Macro Speed
9
Strobe
10
Dimmer
Geyser P4 User Manual Rev. 2 Page 13 of 19
Page 14
Configuration
(Wireless Remote
remote control, follow the
(Standalone)
To control the product without a DMX controller;
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Set it to be triggered for either up-close or with the wireless remote.
Programmable
Color Selection
<MANUAL>
Programmable
Color Selection
Control)
Wireless Remote
Control
To select the preset color program when using the <MANUAL> button on the product,
follow the instructions below:
1. Press <MENU> repeatedly until nCoL shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select either P 0 (for blackout) or
P 1–P32 (to choose one of 32 preset colors).
4. Press <ENTER>.
5. Use <UP> or <DOWN> to scroll through P 1–P32.
6. To select that program color, press <ENTER>.
To select the preset color program using the wireless
instructions below:
1. Press <MENU> repeatedly until CH-1–CH-4 shows on the display. Select CH-1,
CH-2, CH-3, or CH-4 to choose that color program.
Note: The color program numbers correspond with the numbered buttons on the
wireless transmitter.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select P1 1–P1 32 (to choose one of 32 preset color
programs).
4. Press <ENTER>.
5. Repeat steps 1–4 to configure the other buttons for the remote.
LED
indicator
(ready)
LED indicator
(heating)
Page 14 of 19 Geyser P4. User Manual Rev. 2
Fog
Triggers
Wireless
Receiver
Wireless
Dipswitches
Transmitter
To trigger fog output and activate the color program using the wireless remote control, do
the following:
1. Plug the wireless receiver into the Remote Control Receiver port on the side of the
Geyser P4
2. On the wireless transmitter, press the button assigned to the color program (1–4).
The Geyser P4 emits fog and activates the color program for as long as you hold
down the button.
Page 15
Fogger
After every 40 hours of continuous
through the system to prevent the
Fog Cleaner Quart (FCQ) was specifically developed by Chauvet to clean your
cleanings, to increase the life of your fogger.
Storage/
Before storing the fogger, run FCQ through the system as described in the cleaning
Do not refill the tank with
Cleaning the system prior to storage will help prevent
5. TECHNICAL INFORMATION
Do not allow the fogger to become clogged.
Maintenance
operation, use CHAUVET Fog Cleaner Quart (FCQ)
accumulation of particulate matter in the heating element.
The recommended cleaning procedure is as follows.
1. Unplug the product from power.
2. Empty all fog fluid from the machine.
3. Add cleaning solution to the tank.
4. Plug in the product and allow it to warm up.
5. Run the machine in a well-ventilated area until the tank is almost empty. Do not
allow the pump to run dry!
6. Refill with fog fluid. Run the machine briefly to clear any cleaning solution from the
pump and heater.
Geyser P4 Make sure you use FCQ regularly, no longer than 90 days between
Maintenance
procedure above; however, only follow steps 1 through 5.
fog fluid if storing the fogger.
any particles from condensing inside the pump or heater while not in use.
Test-run your Geyser P4 on a monthly basis to achieve the best performance.
Geyser P4 User Manual Rev. 2 Page 15 of 19
Page 16
General Troubleshooti ng
Clean thoroughly with CHAUVET® FCQ. For
with CHAUVET® water-based fog fluid.
Excessive load on the
circuit
Make sure that the total load does not exceed
80% of the breaker or fuse nominal current
Short circuit along the
power lines
Check the power lines and power cords
No energy on power
outlet
Check power outlet
Change to another outlet
Loose or damaged
power cord
Check the power cord
Blown fuse
Replace blown fuse with a good one of the
same type and rating
Internal problem
Send product for repair
No fluid
Turn the product off and replenish the fog fluid
(use only CHAUVET® water-based fog fluid)
Heater or pump
Clean thoroughly with CHAUVET® FCQ. For
with CHAUVET® water-based fog fluid.
Wired remote
defective
Make sure that the remote is connected
available
Inappropriate wired
remote operation
See Wireless Remote Control for instructions
Wireless remote
connected
Make sure that the wireless remote receiver is
Wireless remote
battery
Replace battery on wireless remote transmitter
Internal problem
Send the product for repair
Symptom Display Possible Cause Possible Action
No output or
low output or
fog machine is
spitting fluid
Circuit breaker or fuse
keeps blowing
Product does not
power up
Product does not
output fog
“Addr” or “HEAT”
Off
Off
“Addr” or “HEAT”
Wrong fluid
Blocked pipes or
failing part
clogged
disconnected or
receiver not
full instructions, see Fogger Maintenanc e. Refill
Contact Customer Service
full instructions, see Fogger Maintenanc e. Refill
Try the remote on another Geyser P4 if
connected
If you still experience problems after trying the above solutions, contact Chauvet
Technical Support.
transmitter ran out of
Page 16 of 19 Geyser P4. User Manual Rev. 2
Page 17
Dimensions and
Length
Width
Height
Weight
13.4 in (340 mm)
10.2 in (260 mm)
7 in (180 mm)
12.4 lb (5.6 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
120 VAC, 60 Hz
or 230 VAC, 50 Hz
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
1300 W
1300 W
Operating current
10.6 A
5.6 A
Fuse
F 13 A, 250 V
F 13 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
7.3 W
50,000 hours
Parameter
Illuminance
485 lux @ 2 m
Color
Quantity
Current
RGBA+UV
4
2.5 A
Operation/Capacity/
Consumption
Heat-up Time
Tank Capacity
Fluid Consumption
2 min
2.5 l (0.7 gal)
80 ml/min
Misc.
Output
13,500 cfm
Thermal
Maximum External Temp.
Cooling System
104 °F (40 °C)
Convection
Ordering
Product Name
Item Code
UPC Number
Geyser P4 (120 V)
09071156
781462215040
Geyser P4 (230 V)
09071157
781462215057
6. TECHNICAL SPECIFICATIONS
Weight
Model-specific
Fixed
Geyser P4 User Manual Rev. 2 Page 17 of 19
Page 18
, contact
Returns
Support office and request a Return
. Be prepared to
the cause for the
You must send the merchandise prepaid, in its original box, and with its original packing
the following information on a piece of paper
properly. Any shipping damage resulting from inadequate
reserves the right to use its own discretion to repair or replace returned
To return a product or request support:
• In the U.S., contact Chauvet World Headquarters (see Contact Us
).
• In the UK or Ireland, contact Chauvet Europe Ltd. (see Contact Us).
• In Mexico, contact Chauvet Mexico (see Contact Us).
• In Benelux, contact Chauvet Europe BVBA (see Contact Us).
• In any other country, DO NOT contact Chauvet. Contact y our distr ibutor. See
www.chauvetlighting.com
for distributors outside the U.S., United Kingdom, Ireland,
Mexico, or Benelux.
If you live outside the U.S., United Kingdom, Ireland, Mexico, or Benelux
your distributor of record and follow their instructions on how to return Chauvet
products to them. Visit our website for contact details.
Call the corresponding Chauvet Technical
Merchandise Authorization (RMA) number before shipping the product
provide the model number, serial number, and a brief description of
return.
and accessories. Chauvet will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write
and place it inside the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product
packaging will be your responsibility. FedEx packing or double-boxing are
recommended.
Chauvet
product(s).
Page 18 of 19 Geyser P4. User Manual Rev. 2
Page 19
C
USA WORLD HEADQUARTERS
General Information – Chauvet
Technical Support
www.chauvetlighting.com
EUROPE
General Information - Chauvet Euro pe BVBA
Technical Support
www.chauvetlighting.eu
General Information - Chauvet Europe Ltd.
Technical Support
MEXICO
General Information - Chauvet Mexico
Voice: +52 (728) 285-5000
Technical Support
www.chauvet.com.mx
Visit the applicable website above to verify our contact information and instructions to
the dealer of record.
ONTACT
US
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: (954) 577-4455
Fax: (954) 929-5560
Toll free: (800) 762-1084
Address: Stokstraat 18
9770 Kruishoutem
Belgium
Voice: +32 9 388 93 97
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: +44 (0)1773 511115
Fax: +44 (0)1773 511110
Address: Av. de las Partidas 34 - 3B, Zona
Industrial Lerma
Lerma, Edo. de Mexico C.P. 52000
Voice: (844) 393-7575
Fax: (954) 756-8015
Email:
chauvetcs@chauvetlighting.com
World Wide Web
Email:
Eutech@chauvetlighting.eu
World Wide Web
Email:
uktech@chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk
Email: servicio@chauvet.com.mx
World Wide Web
request support. Outsid e the U.S., United Kingdom, Ireland, Mexico or Ben elux, contact
Geyser P4 User Manual Rev. 2 Page 19 of 19
Loading...