Page 1
User Manual
Page 2
Table of Contents
TABLE OF CONTENTS
1. Before You Begin ....................................................................... 1
What Is Included ........................................................................................... 1
Unpacking Instructions.................................................................................. 1
Claims ..................................................................................................................... 1
Text Conventions .......................................................................................... 1
Symbols ........................................................................................................ 1
Disclaimer ..................................................................................................... 1
Intellectual Property ...................................................................................... 1
Safety Notes.................................................................................................. 2
2. Introduction ................................................................................ 3
Product Overview.......................................................................................... 3
Product Dimensions ...................................................................................... 4
3. Setup ........................................................................................... 5
AC Power...................................................................................................... 5
Fuse Replacement .................................................................................................. 5
Power Linking.......................................................................................................... 5
Power-Linking Diagram ........................................................................................... 5
Battery Power................................................................................................ 6
Charging the Battery ............................................................................................... 6
Battery Life Indicator ............................................................................................... 6
Battery Run Time .................................................................................................... 6
4. Operation .................................................................................... 7
Control Panel Operation................................................................................ 7
Menu Map ..................................................................................................... 7
Configuration (DMX) ..................................................................................... 7
Starting Address...................................................................................................... 7
DMX Personalities................................................................................................... 8
DMX Channel Assignments and Values ....................................................... 8
8Ch.......................................................................................................................... 8
4Ch.......................................................................................................................... 8
Configuration (Bluetooth) .............................................................................. 9
Configuration (Standalone) ........................................................................... 9
Automatic Programs................................................................................................ 9
Auto-Program Speed............................................................................................... 9
Sound-Active Mode ................................................................................................. 9
Preset Color Mode .................................................................................................. 9
Custom Color Mixing ............................................................................................... 9
IRC-6 Infrared Remote Control ..................................................................... 10
IRC-6 Operation ...................................................................................................... 10
Master/Slave Mode ....................................................................................... 11
5. Maintenance................................................................................ 12
Product Maintenance .................................................................................... 12
6. Technical Specifications ........................................................... 13
Returns............................................................................................ 14
Contact Us ...................................................................................... 15
EZLink Par Q4BT User Manual Rev. 7
Page 3
Before You Begin
1. Before You Begin
What Is Included
•EZLinkParQ4BT
•Power cord
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure all the parts are in the
package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear damaged from shipping, or show
signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier
immediately may invalidate your claim. In addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or concealed
damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Convention Meaning
1–512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified
<ENTER> A key to be pressed on the product’s control panel
ON A value to be entered or selected
• Quick Reference Guide
Symbols
Symbol Meaning
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these
instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects. However,
Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss,
damage or disruption caused by any errors or omissions in this document, whether such errors or
omissions result from negligence, accident or any other cause. Chauvet reserves the right to revise the
content of this document without any obligation to notify any person or company of such revision, however,
Chauvet has no obligation to make, and does not commit to make, any such revisions. Download the latest
version from www.chauvetdj.com
.
Intellectual Property
The works of authorship contained in this manual, including, but not limited to, all design, text and images
are owned by Chauvet.
© Copyright 2020 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, and EZLink Par Q4BT are registered trademarks or trademarks of Chauvet
& Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other
company and product names and logos referred to herein may be trademarks of their respective
companies.
EZLink Par Q4BT User Manual Rev. 7
Page 1 of 15
Page 4
Safety Notes
• This product is not intended for permanent installation.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power by pulling or tugging on the cord.
• Make sure there are no flammable materials close to the product when operating.
• Do not touch the product’s housing when operating because it may be very hot.
• The voltage of the outlet to which you are connecting this product must be within the range
stated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the
product to rain or moisture.
• This product is intended for floor mounting only. Do not hang overhead.
• Always place the product in a location with adequate ventilation, at least 20 in (50 cm) from
adjacent surfaces.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer or rheostat.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part.
• The maximum ambient temperature is 104 °F (40 °C). Do not operate this product at higher
temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Do not open this product. It contains no user-serviceable parts.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Before You Begin
Keep this User Manual for future use. If the product is sold to someone else, be sure that they
also receive this document.
Page 2 of 15
EZLink Par Q4BT User Manual Rev. 7
Page 5
Introduction
DMX
in/out
Power
out
Menu
buttons
Display
Power
in
Power
switch
Microphone
LED
indicators
2. Introduction
Product Overview
EZLink Par Q4BT User Manual Rev. 7
Page 3 of 15
Page 6
Product Dimensions
A
5.7 in
145 mm
5.6 in
143 mm
5.7 in
145 mm
Introduction
Page 4 of 15
EZLink Par Q4BT User Manual Rev. 7
Page 7
Setup
Safety cap
Spare fuse holder
(inside safety cap)
Installed fuse
(held by plastic clip)
1st product
2
nd
product3rd product
Power
source
Additional
products
3. Setup
AC Power
The EZLink Par Q4BT has an auto-ranging power supply and it can work with an input voltage range of
100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current
value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
The listed current rating indicates the product’s average current draw under normal conditions.
• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure
the product has an appropriate electrical ground to avoid the risk of electrocution or
fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse Replacement
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder and replace with a fuse of the exact same type and rating.
5. Insert the fuse holder back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
Power Linking
The product provides power linking via the outlets located in the back of the product. See the diagram
below for further explanation.
Power-Linking Diagram
You can power link up to 27 EZLink Par Q4BT products on 120 VAC or up to 50
EZLink Par Q4BT products on 230 VAC.
The power linking diagram shown above corresponds to the North American version of
the product ONLY! If using the product in other markets, you must consult with the local
Chauvet distributor as power linking connectors and requirements may differ in your
country or region.
EZLink Par Q4BT User Manual Rev. 7
Page 5 of 15
Page 8
Setup
100% 75% 50% 25%
Battery Power
The EZLink Par Q4BT comes with a rechargeable lithium battery for cable free operation.
Charging the Battery
The battery charges whenever the EZLink Par Q4BT is plugged into a power source using the included
power cord. If the product is plugged in and not in operation, make sure the product is turned off.
• The LED indicator light will flash if you overpower your units.
• DO NOT use the EZLink Par Q4BT on full power mode (all LEDs at 100%) while it is
being charged/plugged into a power source, as the unit will get extremely hot.
Battery Life Indicator
The indicators on the LED Menu Display show how much battery life remains available. The drawing below
provides a key to reading the battery life indicators.
Battery Run Time
Maximum Run Time (all colors on) Recharge Time
Up to 8 hours 7.5 hours
Page 6 of 15
EZLink Par Q4BT User Manual Rev. 7
Page 9
Operation
4. Operation
Control Panel Operation
To access the control panel functions, use the four buttons located underneath the display. Please refer to
the Product Overview
Button Function
<MENU> Press to find an operation mode or to back out of the current menu option
<UP> Press to scroll up the list of options or to increase the numeric value in a function
<DOWN> Press to scroll down the list of options or to decrease the numeric value in a function
<ENTER> Press to activate a menu option or set the selected value in a function
Menu Map
Mode Programming Levels Description
DMX Mode
Static Colors C-- C 1–15 Static colors
Automatic
Programs
Auto Speed S-- S. 1–100 Program speed for P1–5, slow to fast
Dimmer
Sound-
Active Mode
Sensitivity SEnS u 0–u100 Sound sensitivity
Custom
Color Mixing
Bluetooth
Mode*
Control
Mode
*The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of
such marks by Chauvet & Sons, LLC is under license. Other trademarks and trade names are those of their respective
owners.
to see the button locations on the control panel.
4Ch
8Ch 8-channel DMX mode
P-- P 1–5 Automatic programs
d-- L. 1–255 Dimmer for the Auto/Sound programs
Snd Snd1–5 Sound-active programs
u--
bLE _ _ _ _ _ Bluetooth control mode, displays Bluetooth ID
SEt
d 1–509
r. 0–255
G. 0–255
b. 0–255
A. 0–255
S. 0–100 Strobe rate
ir
out
on
oFF
SLAV Enables Master/Slave with other BT products
dMX Enables Master/Slave with non-BT products
4-channel DMX mode
Custom static colors combine red, green, blue,
and amber
Turns infrared on or off
Configuration (DMX)
The EZLink Par Q4BT works with a DMX controller. Information about DMX is in the CHAUVET DMX
Primer, which is available from the Chauvet website:
http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels the selected DMX
mode uses. If the starting address is set too high, access to some of the product’s channels could be
restricted.
The EZLink Par Q4BT uses up to 8 DMX channels, which defines the highest configurable address is 505.
For information about the DMX protocol, download the DMX Primer from www.chauvetdj.com
To select the starting address, do the following:
1. Press <MENU> repeatedly until 4Ch or 8Ch shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select the starting address, from d 1–509 (4Ch) or d 1–505 (8Ch).
4. Press <ENTER>.
EZLink Par Q4BT User Manual Rev. 7
.
.
Page 7 of 15
Page 10
Operation
DMX Personalities
The EZLink Par Q4BT has two DMX personalities: a 4-channel personality and an 8-channel personality.
To select a DMX personality, follow the instructions below.
1. Press <MENU> to view menu options on the display.
2. Use <UP> or <DOWN> to select the DMX personality, from 4Ch or 8Ch.
3. Press <ENTER>.
DMX Channel Assignments and Values
8Ch
Channel Function Value Percent/Setting
1 Red 000 255 0–100%
2 Green 000 255 0–100%
3Blue 000 255 0–100%
4 Amber 000 255 0–100%
5 Strobe
6 Auto Programs
7 Auto Speed
8 Dimmer 000 255 0–100%
000 015 No Function
016 255 Strobe, slow to fast
000 005 No function
006 055 Auto program 1 (programs 2–7)
056 106 Auto program 2
107 157 Auto program 3
158 208 Auto program 4
209 255 Auto program 5
000 250 Program speed, slow to fast
251 255 Sound-active program
4Ch
Channel Function Value Percent/Setting
1 Red 000 255 0–100%
2 Green 000 255 0–100%
3Blue 000 255 0–100%
4 Amber 000 255 0–100%
Page 8 of 15
EZLink Par Q4BT User Manual Rev. 7
Page 11
Operation
Configuration (Bluetooth)
The EZLink Par Q4BT can be operated with the BTAir application over a Bluetooth connection (Bluetooth
version 4.2):
1. Download and install the BTAir app from your preferred app store.
2. Press <MENU> repeatedly until bLE shows on the display.
3. Press <ENTER>.
The app will find and pair automatically to all the BT series products within range.
Configuration (Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
Never connect a product that is operating in any standalone mode to a DMX string
connected to a DMX controller. Products in standalone mode may transmit DMX signals
that could interfere with the DMX signals from the controller.
Automatic Programs
To run the EZLink Par Q4BT in automatic mode, follow the instructions below:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select an automatic program, from P 1–5.
4. Press <ENTER>.
Auto-Program Speed
To set the auto-program speed on the EZLink Par Q4BT, do the following:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to increase or decrease the program speed, from S. 1–100.
3. Press <ENTER>. The product will return to Auto mode.
Sound-Active Mode
To run the EZLink Par Q4BT in sound-active mode, follow the instructions below:
1. Press <MENU> repeatedly until Snd shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select a sound-active program, from Snd1–5.
4. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
Preset Color Mode
To run the EZLink Par Q4BT on a preset static color, do the following:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select a static color, from C 1–15.
4. Press <ENTER>.
Custom Color Mixing
To mix a custom static color on the EZLink Par Q4BT, do the following:
1. Press <MENU> repeatedly until u-- shows on the display.
2. Press <ENTER> and one of the following will show on the display:
• r. _ _ _ (red)
• G. _ _ _ (green)
• b. _ _ _ (blue)
• A. _ _ _ (amber)
• S. _ _ _(strobe rate)
3. Press <ENTER> to cycle through the options.
4. Use <UP> or <DOWN> to increase or decrease the selected value, from 0–255 (for red, green,
blue, or amber) or from 0–100 (for strobe rate).
• Strobe rate - 0: no function, 1–99: slow to fast, 100: sound-active.
5. Repeat steps 3 and 4 until the color is set as desired.
EZLink Par Q4BT User Manual Rev. 7
Page 9 of 15
Page 12
BLACK
OUT
AUTO
SOUND
SENSITIVITY
SPEEDSTROBE
%
MANUAL
FADE
RGB
WUVA
+ 0
-
123
654
789
Operation
IRC-6 Infrared Remote Control
The EZLink Par Q4BT is compatible with the IRC-6 infrared remote control from Chauvet. To activate IR
mode, follow the instructions below:
1. Press <MENU> repeatedly until SEt shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select ir.
4. Press <ENTER>.
5. Use <UP> or <DOWN> to select on.
6. Press <ENTER>.
IRC-6 Operation
Automatic Mode
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode (snap) with the IRC-6:
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to choose between the different auto programs.
To select only fading programs:
1. Press <FADE> on the IRC-6.
2. Press <+> or <–> to choose between the different fading programs.
To adjust the speed of the automatic program:
1. Press <SPEED> on the IRC-6.
2. Press <+> or <–> to increase or decrease the speed of the program.
Sound-Active Mode
To turn on Sound-Active mode with the IRC-6:
1. Press <SOUND> on the IRC-6.
2. Press <+> or <–> to select a sound-active program.
To adjust the sound sensitivity:
1. Press <SENSITIVITY> on the IRC-6.
2. Press <+> or <–> to increase or decrease the sensitivity.
Manual Color Control
To select a preset static color with the IRC-6:
1. Press <MANUAL> on the IRC-6.
2. Press any number between 0–9 to choose your color.
To manually control the RGB percentage with the IRC-6:
1. Press <MANUAL> on the IRC-6.
2. Select the color to be edited, from <R> (red), <G> (green),<B> (blue), or
<A> (amber).
3. Press <+> or <–> to increase or decrease the value of the selected color.
4. Repeat steps 2 and 3 until the product outputs as desired.
Strobe
To adjust the strobe rate with the IRC-6:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
3. Press <STROBE> again to turn off the strobe.
Dimmer
To adjust the total output with the IRC-6:
1. Press <%> on the IRC-6.
2. Press <+> or <–>
Black Out
To black out the lights with the IRC-6:
1. Press <BLACK OUT> on the IRC-6.
This will turn off all the lights until the button is pressed again.
The IRC-6 will not respond to any inputs when Black Out is activated. If
the remote does not respond when a button is pressed, try pressing
<BLACK OUT>. You may have inadvertently activated Black Out.
Page 10 of 15
to increase or decrease the output level.
EZLink Par Q4BT User Manual Rev. 7
Page 13
Operation
Master/Slave Mode
The Master/Slave mode allows a single EZLink Par Q4BT product (the “master”) to control the actions of
one or more EZLink Par Q4BT products (the “slaves”) without the need of a DMX controller. The master
product will be set to operate in standalone or with the IRC-6, while the slave products will be set to
operate in slave mode. Once set and connected, the slave products will operate in unison with the master
product.
Configure the products as indicated below.
Slave products:
1. Press <MENU> repeatedly until
2. Press <ENTER>.
3. Set the DMX address to d 1.
4. Connect the DMX input of the first slave product to the DMX output of the master product.
5. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave
product.
6. Finish setting and connecting all the slave products.
Master product:
1. Press <MENU> repeatedly until SEt shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select out.
4. Press <ENTER>.
5. Press <UP> or <DOWN> to select dMX (to Master/Slave with non-BT products) or SLAV (to
Master/Slave with other BT products).
6. Press <ENTER>.
7. Set the master product to operate in standalone or IR mode.
8. Make the master product the first product in the DMX daisy chain.
• Configure all the slave products before connecting the master to the daisy chain.
• Never connect a DMX controller to a DMX string configured for Master/Slave operation
because the controller may interfere with the signals from the master.
• Do not connect more than 31 slaves to the master.
4Ch
shows on the display.
EZLink Par Q4BT User Manual Rev. 7
Page 11 of 15
Page 14
Maintenance
5. Maintenance
Product Maintenance
Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of
the light source’s life and/or mechanical wear. To maintain optimum performance and minimize wear, clean
your lighting products at least twice a month. However, be aware that usage and environmental conditions
could be contributing factors to increase the cleaning frequency.
To clean the product, follow the instructions below:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external
surface/vents.
4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens-cleaning tissue.
6. Softly drag any dirt or grime to the outside of the transparent surface.
7. Gently polish the transparent surfaces until they are free of haze and lint.
Always dry the transparent surfaces carefully after cleaning them.
Do not spin the cooling fans using compressed air because they could be damaged.
Page 12 of 15
EZLink Par Q4BT User Manual Rev. 7
Page 15
Technical Specifications
6. Technical Specifications
Dimensions and Weight
Length Width Height Weight
5.7 in (145 mm) 5.7 in (145 mm) 5.6 in (143 mm) 2.8 lb (1.3 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type Range Voltage Selection
Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging
Parameter 120 V, 60 Hz 230 V, 50 Hz
Consumption 26 W 24 W
Operating current 0.3 A 0.2 A
Fuse F 1 A, 250 V F 1 A, 250 V
Power I/O U.S./Worldwide UK/Europe
Power input connector IEC IEC
Power cord plug Edison (U.S.) Local plug
Light Source
Type Color Quantity Power Current Lifespan
LED
Photometrics
Strobe Rate Beam Angle Field Angle Illuminance @ 2 m
0 to 25 Hz 15° 34° 1,306 lux
Thermal
Maximum External Temperature Cooling System
104 °F (40 °C) Fan-assisted convection
DMX
I/O Connector Channel Range Optional Controllers
3-pin XLR 4 or 8 IRC-6
Ordering
Product Name Item Code UPC Number
EZLink Par Q4BT 10031540 781462218881
Quad-color
RGBA
4 3 W 1 A 50,000 hours
EZLink Par Q4BT User Manual Rev. 7
Page 13 of 15
Page 16
Returns
Returns
In case you need to get support or return a product:
• If you are located in the U.S., contact Chauvet World Headquarters.
• If you are located in the U.K. or Ireland, contact Chauvet Europe Ltd.
• If you are located in Benelux, contact Chauvet Europe BVBA.
• If you are located in France, contact Chauvet France.
• If you are located in Germany, contact Chauvet Germany.
• If you are located in Mexico, contact Chauvet Mexico.
• If you are located in any other country, DO NOT contact Chauvet. Instead, contact your local
distributor. See www.chauvetdj.com
France, Germany, or Mexico.
If you are located outside the U.S., UK, Ireland, Benelux, France, Germany, or Mexico,
contact your distributor of record and follow their instructions on how to return Chauvet
products to them. Visit our website www.chauvetdj.com
Call the corresponding Chauvet Technical Support office and request a Return Merchandise Authorization
(RMA) number before shipping the product. Be prepared to provide the model number, serial number, and
a brief description of the cause for the return.
To submit a service request online, go to www.chauvetdj.com/service-request
Send the merchandise prepaid, in its original box, and with its original packing and accessories. Chauvet
will not issue call tags.
Clearly label the package with the RMA number. Chauvet will refuse any product returned without an RMA
number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number directly
on the box.
for distributors outside the U.S., U.K., Ireland, Benelux,
for contact details.
.
Before sending the product, clearly write the following information on a piece of paper and place it inside
the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be
your responsibility. FedEx packing or double-boxing are recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
product(s).
Page 14 of 15
EZLink Par Q4BT User Manual Rev. 7
Page 17
Contact Us
Contact Us
Chauvet World Headquarters
Chauvet Europe Ltd
Chauvet Europe BVBA
Chauvet France
Chauvet Germany
Chauvet Mexico
Address: Av. de las Partidas 34 - 3B
Lerma, Edo. de México, CP 52000
General Information Technical Support
Address: 5200 NW 108th Ave. Voice: (844) 393-7575
Sunrise, FL 33351 Fax: (954) 756-8015
Voice: (954) 577-4455 Email: chauvetcs@chauvetlighting.com
Fax: (954) 929-5560
Toll Free: (800) 762-1084 Website: www.chauvetdj.com
Address: Unit 1C Email: UKtech@chauvetlighting.eu
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK Website: www.chauvetdj.eu
NG16 6NT
Voice: + 44 (0) 17 7 3 511115
Fax : + 44 (0) 1 7 7 3 511110
Address: Stokstraat 18 Email: BNLtech@chauvetlighting.eu
9770 Kruishoutem
Belgium Website: www.chauvetdj.eu
Voice: +32 9 388 93 97
Address: 3, Rue Ampère
91380 Chilly-Mazarin
France Website: www.chauvetdj.eu
Voice: +33 1 78 85 33 59
Address: Bruno-Bürgel-Str. 11
28759 Bremen
Germany Website: www.chauvetdj.eu
Voice: +49 421 62 60 20
(Entrance by Calle 2)
Zona Industrial Lerma Website: www.chauvetdj.mx
Voice: +52 (728) 690-2010
Email: FRtech@chauvetlighting.fr
Email: DEtech@chauvetlighting.de
Email: servicio@chauvet.com.mx
Visit the applicable website above to verify our contact information and instructions to request support. Outside
the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact the dealer of the record.
EZLink Par Q4BT User Manual Rev. 7
Page 15 of 15
Loading...