Chauvet CH-330 Triple Derby User Manual

CH-330

Triple Derby™

USER MANUAL

Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A

[phone] – [phone]

FAX [phone]

www.chauvetlighting.com

2006-08-25/20:37

TABLE OF CONTENT

TABLE OF CONTENT........................................................................................................................................................... 2

BEFORE YOU BEGIN........................................................................................................................................................... 3

WHAT IS INCLUDED................................................................................................................................................................................ 3

UNPACKING INSTRUCTIONS....................................................................................................................................................................3

AC POWER...........................................................................................................................................................................................3

SAFETY INSTRUCTIONS..........................................................................................................................................................................3

INTRODUCTION ................................................................................................................................................................... 4

FEATURES............................................................................................................................................................................................4

PRODUCT OVERVIEW ............................................................................................................................................................................4

SETUP................................................................................................................................................................................... 5

LAMP ...................................................................................................................................................................................................5

Lamp installation ................................................................................................................................................................................................ 5

MOUNTING ...........................................................................................................................................................................................5

Orientation..........................................................................................................................................................................................................5

Rigging ...............................................................................................................................................................................................................5

OPERATING INSTRUCTIONS.............................................................................................................................................. 6

Duty Cycle..................................................................................................................................................................... 6

APPENDIX............................................................................................................................................................................. 7

GENERAL MAINTENANCE .......................................................................................................................................................................7

RETURNS PROCEDURE..........................................................................................................................................................................7

CLAIMS ................................................................................................................................................................................................7

GENERAL TROUBLESHOOTING................................................................................................................................................................ 8

LAMP (IN-SERIES) WIRING FOR 230V OPERATION....................................................................................................................................9

TECHNICAL SPECIFICATIONS ..................................................................................................................................................................9

TECHNICAL SUPPORT............................................................................................................................................................................9

CH-330 User Manual 2 2006-08-25/20:37

BEFORE YOU BEGIN

What is included

¾ 1 x Triple Derby™ (CH-330)
¾ Power cord with plug

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.

AC Power

To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch. Before applying power to a
fixture, check that the source voltage matches the fixture’s requirement.
Check the fixture or device carefully to make sure that if a voltage selection
switch exists that it is set to the correct line voltage you will use.

For lamp installation in 230V environments please read “Lamp (I n­Series) Wiring” in the Appendix section of this manual.

¾ 2 x 64514 300w 120V
¾ Warranty Card & Manual

AC Voltage Switch

Warning! Verify that the power select switch on your unit matches the line voltage applied. All

fixtures must be connected to circuits with a suitable Earth Ground.

Not all fixtures have a voltage
select switch. Please be sure to
connect to the proper voltage.

Safety Instructions

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance?

• Please keep this User Guide for future consultation. If you
sell the unit to another user, be sure that they also receive
this instruction booklet.

• Always make sure that you are connecting to the proper
voltage and that the line voltage you are connecting to is
not higher than that stated on decal or rear panel of the
fixture.

• This product is intended for indoor use only!

• To prevent risk of fire or shock, do not expose fixture to

rain or moisture. Make sure there are no flammable
materials close to the unit while operating.

• The unit must be installed in a location with adequate
ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.

• Always disconnect from power source before servicing or
replacing lamp or fuse and be sure to replace with same
lamp source.

• Secure fixture to fastening device using a safety chain.
Never carry the fixture solely by its head. Use its carrying
handles.

• Maximum ambient temperature is Ta: 40°. Do not operate
fixture at temperatures higher than this.

• In the event of serious operating problem, stop using the
unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the
same type spare parts.

• Don’t connect the device to a dimmer pack.

• Make sure power cord is never crimped or damaged.

• Never disconnect power cord by pulling or tugging on the

cord.

• Avoid direct eye exposure to lamp while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the housing or

attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET.

CH-330 User Manual 3

2006-08-25/20:37

INTRODUCTION

Features

• Sound-activated

• 24 lenses, 48 beams

• Sound Sensitivity knob

• Built-in microphone

• Safety hook

• Fan cooled

Product Overview

Lamp access

Hanging bracket

Safety hook

Voltage select switch

Sound sensitivity knob

Fuse

Microphone

CH-330 User Manual 4

2006-08-25/20:37

SETUP

Lamp

You may need to install a lamp prior to the initial operation of the fixture. Two 64514 300W halogen
bi-pin lamps are included.

Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to
cool down! Always disconnect from main power prior to lamp replacement.

Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp
with alcohol and wipe it with a lint free cloth before installation.

For lamp installation in 230V environments please read “Lamp (In-Series) Wiring” in the
Appendix section of this manual.

Mounting

LAMP INSTALLATION

1) Remove the (S1) screw located on top of the
fixture as shown in the image.

2) Flip open to expose lamp and socket.

3) If replacing the lamp, remove old lamp first.

4) Using a cloth or napkin hold the bulb and
pull out of the lamp socket located inside the
reflector.

5) Replace with a new lamp.

6) Flip cover to close, align the screw hole and
fasten the screw.

S1

Lamp cover

plate

ORIENTATION

This fixture may be mounted in any position provided there is adequate room for ventilation.

RIGGING

It is important never to obstruct the fan or vents pathway. Mount the fixture using, a suitable “C” or “O”
type clamp. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding
the desired position, retighten both knobs.

Hanging Clamp

• When selecting installation location, take into consideration lamp
replacement access and routine maintenance.

• Safety cables should always be used.

• Never mount in places where the fixture will be exposed to rain, high

humidity, extreme temperature changes or restricted ventilation.

CH-330 User Manual 5

2006-08-25/20:37

Appendix

OPERATING INSTRUCTIONS

The Triple Derby™ is a high output sound activated effect light. It produces 48 beams that rotate back
and forth to the music. Sensitivity to sound can be adjusted at the rear of the fixture.

Whether used in a mobile or permanent environment, you may find it useful to control this effect by
means of a relay system for remote switching or to go with DMX control, use the latest in DMX
compatible (Relay Pack), all available from CHAUVET.

A relay system will allow you to remotely trigger the Scrambler™ and any other non-dimmable effect
light from a switch panel. Make sure to use a cable of at least 25 feet to provide ample distance
between the control panel and the switch pack for most mobile lighting applications.

If you would prefer to control it directly from your DMX lighting console then we suggest a DMX
compatible (relay switch-pack). These devices are an extremely affordable solution to operating non­DMX lighting effects remotely.

Duty Cycle

It is necessary to cycle On and Off this fixture every 15 minutes due to the high temperature created
while in use. For every 15 minute period that the fixture is used, allow 15 minutes in the Off position to
cool down. Please do not exceed 15 minutes of On operation per cycle.

To learn more about these and other CHAUVET products visit us at www.chauvetlighting.com

.

CH-330 User Manual 6

2006-08-25/20:37

APPENDIX

General Maintenance

To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.

Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or
becomes dirty, clean the lamps with an alcohol wipe.

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Returns Procedure

Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.

Claims

Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.

CH-330 User Manual 7

2006-08-25/20:37

Appendix

General Troubleshooting

Applies to

Symptom Solution(s)

Lights

Foggers
& Snow

Controllers

Dimmers

& Chaser

Auto shut off Check fan thermal switch reset
Beam is very dim or not

bright

Breaker/Fuse keeps

Clean optical system or replace lamp
Check 220/110v switch for proper setting

Check total load placed on device

blowing
Chase is too slow Check users manual for speed adjustment
Device has no power Check for power on Mains.

Check device’s fuse. (internal and/or external)

Fixture is on but there
is no movement to the
audio

Make sure you have the correct audio mode on the control
switches. If audio provided via ¼” jack, make sure a live
audio signal exists

Adjust sound sensitivity knob

Fluid indicator not
working

The filter tip on the end of the tube inserted into the fluid
container must float freely in order to measure correctly,
check to see if perhaps it is stuck

Fogger or Snow output
has dropped

Lamps cuts off
sporadically

Light will not come on
after power failure

Clean with distilled water and vinegar
Replace hose

Possible bad lamp or fixture is overheating.
Lamp may be at end of its life.

Some discharge lamps require a cooling off period before
the electronics in the fixture can kick start it again, wait 5 to
10 minutes before powering up

9

9

9

9

9 9

9 9

9

9

9

9

9

9 9

9

Motor movements are
jerky or jumpy

Possible bad motor driver or sensors

Check polarity switch on controller
Moves slow Check 220/110v switch for proper setting
No flash Re-install bulb, may have shifted in shipping
No fog Check fluid tank if empty

Make sure green light is on (for power)
No light output Check slip ring & brushes for contact

Install bulb

Call service technician
Relay will not work Check reset switch

Check cable connections
Remote does not work Make sure connector is firmly connected to device
Unit wobbles when

Check for damages possibly incurred during shipping
rotating

CH-330 User Manual 8

9

9
9

9

9

9

9 9

9

2006-08-25/20:37

9

Appendix

Lamp (in-series) Wiring for 230V Operation

In prior tests of the 230V version of the 64514 known as the
64516 or 64515, failure of the lamp was common place due
to rapid fixture movement during normal operations and
penetrating sound waves produced in low frequency based
music.

Many customers around the world in places where power is
served at 230V or 240V have noticed that connecting the
64514 (120V) lamps in series is the most effective and
economical method. Tests have shown that the lamp will hold
much longer than their 230V counter parts.

Technical Specifications

WEIGHT & DIMENSIONS

Length.............................................................................................................................. 431 mm (17 in)

Width ............................................................................................................................... 406 mm (16 in)

Height.................................................................................................................................178 mm (7 in)

Weight .......................................................................................................................... 10.4 Kgs (23 lbs)

POWER

Switch selectable power..................................................................................115V 60Hz or 230V 50Hz

DUTY CYCLE (RECOMMENDED)

1. Fixture ON.................................................................................................(not to exceed) 15 minutes

2. Fixture OFF ...............................................................................................(cool down for) 15 minutes

LAMPS

64514.....................................................................................................................................300W 120V

(230V) - 64514 x (2) In-Series...............................................................................................300W 120V

THERMAL

Maximum ambient temperature............................................................................................ 40° (104° F)

FUSE

Main (115V)..........................................................................................20mm Glass 7A 125V Fast Blow

Main (230V)..........................................................................................20mm Glass 5A 250V Fast Blow

ORDERING INFORMATION

Triple Derby™ ............................................................................................................................. CH-330

Fuse 7A............................................................................................................................P170FUSE007

Technical Support

Address: Service Dept.
3000 N 29
Support (Email): [e-mail]
Telephone: [phone] - (Press 4)
Fax: [phone] - (Attention: Service)
Website: http://www.chauvetlighting.com

CH-330 User Manual 9

th

Ct, Hollywood, FL 33020 (U.S.A.)

2006-08-25/20:37