¾ 1 x Stand (7ft max height)
¾ 1 x Par 38 Red LED’s
¾ 1 x Par 38 Green LED’s
¾ 1 x Par 38 Blue LED’s
¾ 1 x Par 38 Yellow LED’s
¾ 1 x Footswitch
¾ 1 x Switchpack
¾ 1 x Warranty Card
¾ 1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to
ensure that all parts are present, and have been received in good condition. Notify the
shipper immediately and retain packing material for inspection if any parts appear
damaged from shipping or the carton itself shows signs of mishandling. Save the carton
and all packing materials. In the event that a fixture must be returned to the factory, it is
important that the fixture be returned in the original factory box and packing.
LED-PAR 38 System™ User Manual 2 6/24/2008 3:39 PM
Page 3
Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of this
product.
•Please keep this User Guide for future consultation. If you sell the unit to
another user, be sure that they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the
line voltage you are connecting to is not higher than that stated on the decal or
rear panel of the fixture.
•The unit must be installed in a location with adequate ventilation, at least 20in
(50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing lamp or fuse
and be sure to replace with same lamp source.
•Secure fixture to fastening device using a safety chain. Never carry the fixture
solely by its head. Use its carrying handles.
•Maximum ambient temperature (Ta) is 104°F (40°C). Do not operate fixture at
temperatures higher than this.
•In the event of a serious operating problem, stop using the unit immediately.
Never try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
• Never connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not open the
housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact CHAUVET at: 954929-1115.
INTRODUCTION
2.
Features
• LED PAR can package
• Ready to go
LED-PAR 38 System™ User Manual 3 6/24/2008 3:39 PM
Page 4
Product Overview
Power Link Out
Led PAR 38’s
Switchpack
Height Adjustment
Channel output
Sound Adjustment
Fuse Holder
Bracket Adjustment
On/Off Switch
LED-PAR 38 System™ User Manual 4 6/24/2008 3:39 PM
Link In
Link Out
Footswitch Input
Page 5
3.SETUP
AC Power
Warning! For 230V operation, you must use 230V LED par cans.
To determine the power requirements for a particular fixture, see the
label affixed to the back plate of the fixture or refer to the fixture’s
specifications chart. A fixture’s listed current rating is its average current
draw under normal conditions. All fixtures must be powered directly off a
switched circuit and cannot be run off a rheostat
(variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel is used solely for a 0% to
100% switch. Before applying power to a fixture, check
that the source voltage matches the fixture’s
requirement. Check the fixture or device carefully to
make sure that if a voltage selection switch exists that
it is set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your
unit matches the line voltage applied. Damage to your fixture
may result if the line voltage applied does not match the
voltage indicated on the voltage selector switch. All fixtures
must be connected to circuits with a suitable Earth Ground.
Figure 1 - AC
Not all fixtures have a voltage
select switch. Please be sure to
connect to the proper voltage.
Warning! All fixtures must be connected to circuits with a suitable Earth
Ground.
LED-PAR 38 System™ User Manual 5 6/24/2008 3:39 PM
Page 6
6.APPENDIX
General Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned
frequently. Usage and environment are contributing factors in determining frequency. As
a general rule, fixtures should be cleaned at least twice a month. Dust build up reduces
light output performance and can cause overheating. This can lead to redu c ed lamp life
and increased mechanical wear. Be sure to power off fixture before conducting
maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove
dust collected on external vents and internal components. Clean all glass when the
fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free
cotton cloth or lens tissue. Apply solution to the cloth or tissue and drag dirt and grime to
the outside of the lens. Gently polish optical surfaces until they are free of haze and lint.
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause
greater accumulation of dirt on the unit’s optics. Clean with soft cloth using normal glass
cleaning fluid. - Always dry the parts carefully. - Clean the external optics at least every
20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not
be issued. Package must be clearly labeled with a Return Merchandise Authorization
Number (RA #). Products returned without an RMA # will be refused. Call CHAUVET and
request RA # prior to shipping the fixture. Be prepared to provide the model number,
serial number and a brief description of the cause for the return. Be sure to properly pack
fixture, any shipping damage resulting from inadequate packaging is the customer’s
responsibility. CHAUVET reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.
Note: If you are given an RMA #, please include the following information on a
piece of paper inside the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage
must be reported to the carrier upon receipt of merchandise. It is the customer's
responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Any other claim for items such as missing component/part,
damage not related to shipping, and concealed damage, must be made within seven (7)
days of receiving merchandise.
LED-PAR 38 System™ User Manual 6 6/24/2008 3:39 PM
Page 7
Technical Support
Address: Service Dept.
3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.)
Support (Email): tech@chauvetlighting.com
Telephone: (954) 929-1115 - (Press 4)
Fax: (954) 929-5560 - (Attention: Service)
Website: http://www.chauvetlighting.com