Page 1
User Manual
Page 2
TABLE OF CONTENTS
1. Before You Begin................................................................................3
What Is Included ........................................................................................... 3
Unpacking Instruc tions .................................................................................. 3
Claims ................................................................................................................... 3
Text Conventions .......................................................................................... 3
Symbols ........................................................................................................ 3
Disclaimer ..................................................................................................... 3
Product at a Glance ....................................................................................... 4
Safety Notes ................................................................................................. 4
2. Introduction.........................................................................................5
Product Overview .......................................................................................... 5
Product Dimensions ...................................................................................... 6
3. Setup ...................................................................................................7
AC Power ...................................................................................................... 7
Fus e Repl acement ................................................................................................. 7
Power Linking ........................................................................................................ 7
Mounting ....................................................................................................... 8
Orientation ............................................................................................................. 8
Rigging .................................................................................................................. 8
4. Operation ............................................................................................9
Control Panel Operation ................................................................................ 9
Menu Map ..................................................................................................... 9
Configuration ( DM X) .................................................................................... 10
Starting Address .................................................................................................. 10
DMX Personalities................................................................................................ 10
DMX Channel Assignments and Values....................................................... 11
11-CH .................................................................................................................. 11
6-CH .................................................................................................................... 13
Configuration ( S tandalone) .......................................................................... 14
Sound-Active Mode .............................................................................................. 14
Automatic Mode ................................................................................................... 14
Manual Pan/Tilt Operation .................................................................................... 14
Pan/Tilt Angle Range ........................................................................................... 14
Display Orientation ............................................................................................... 15
Master/Slave Mode .............................................................................................. 15
Res et Software .................................................................................................... 15
5. Technical Information ......................................................................16
Product Maintenanc e .................................................................................. 16
6. Techni cal Sp eci f ications ..................................................................17
Returns ....................................................................................................... 18
Contact Us .................................................................................................. 18
Page 2 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Page 3
What Is
Unpacking
Instructions
and check the container to make
included
upon receipt
Failure to do so in a timely manner may
cking
For other issues such as missing components or parts, damage not related to shi pping,
Text
Convention
Meaning
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A seq uence of menu opti ons to b e followed
<ENTER>
A key t o be pr essed on th e product’s control panel
ON
A value t o be entered or selected
Symbols
Symbol
Meaning
Critical installation, configuration, or operation informa tion. Failure
the user .
Important installation or configuration information. Failure to
functioning correctly.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
CHAUVET® reserves the right to update the
in the United States of
1. BEFORE YOU BEGIN
Included
Claims
Conventions
• Intimidator™ Spot LED 150
• Hanging Bracket with Mounting
Hardware
Immediately upon r eceipt, carefully unpack the product
sure you have received all the parts indicat ed above in good condition.
If the container or the material inside the container (the product and
accessories) appear damaged from shipp ing, or show signs of mishandling,
notify the carrier immediately, not CHAUVET®.
invalidate your claim with the carrier. In addition, keep t he container and all the pa
material for inspection.
or concealed damage, file a claim with CHAUVET® within 7 days of receiving the
merchandise.
• Power Cord
• Warranty Card
• Quick Reference G uide
omissions that may appear in t his manual.
existing docum ent or t o c reate a new document to correct any errors or omis sions.
You can download the lat est version of this doc ument f rom www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. All rights reserved.
Printed in P.R.C. Electronically published by CHAUVET®
America.
Author Date Editor Date
A. Leon 06/11/13 T. Yeago 06/17/13
to comply could make the product not work, damage it, and harm
comply with this information may prevent the product from
Useful information.
Intimidator™ Spot LED 150 User Manual Rev. 8 Page 3 of 18
Page 4
Product at a
x
P
x
P
P
P
P
x
P
x
Safety Notes
Do not touch the product’s housing when operating because it may be very hot.
• Always m ake s ure that the voltag e of the outlet to which you are connect ing the
center.
Glance
Use on Dimmer
Out door Use
Sound-Activated
DMX
Master/Slave
Please read the following Safet y Not es c arefu lly b efore working with the product. The
Notes include impor tant safety information about installation, usage, and maintenance.
• This product is not intended for permanent installation.
• Always connect the product to a grounded circ uit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing
the fuse.
• Avo id di rect eye exp osure to the l ight sour ce whi le th e product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power cord by pulling or tugging on the cord.
• If mounting the product overhead, always secure to a fastening d evice using a
safety cable.
• Make sure th ere are no flammable materials close t o the product when operating.
•
product is within the range stated on the decal or rear panel of the product.
• The product is for indoor us e only! (I P20) T o prevent risk of fire or shock, do n ot
expose the product to rain or moistu re.
• Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces .
• Be su re that no ventilation slots on the product’s housing are blocked.
• Nev er co nnect the product to a dimmer.
• Make sure to repl ace the fus e w ith a noth er of t he same typ e and r ati ng.
• Nev er ca r ry the product fr om the power cord or an y moving pa rt. Alway s use t he
hanging/mounting bracket or the handles.
• The maximum ambient t emperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Nev er tr y to repair the product. Repairs carried out by unskilled people can lead to
damage or mal function. Please contact the nearest authorized technical assistan ce
Auto Programs
Auto-ranging Power Supply
Replaceable Fuse
User-Serviceable
Duty Cycle
• Keep this User Manual. If you sell the product to another user, be sure that they
also receive this document.
Page 4 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Page 5
2. INTRODUCTION
Product Overview
Power In/Out
Fuse Holder
DMX In/Out
Moving Head
LED Display
Adjustable Lens
Moving Yoke
Cooling Fan
Intimidator™ Spot LED 150 User Manual Rev. 8 Page 5 of 18
Page 6
Product Dimensions
Page 6 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Page 7
AC Power
ranging power supply and i t can work with
(circuit breaker or fuse). Make
an appropriate electrical ground to avoid the risk of
a rheostat (variable resistor) or dimmer circuit, even
Fuse
Power Linking
of the unit.
s on 120 VAC or up to
The power linking diagram shown above corresponds to the North American
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
1st Product
2nd Product
3rd Product
Other products
3. SETUP
Replacement
The Intimidator™ Spot LED 150 has an autoan input voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and
wiring), use the current value li sted on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal condition s.
Always connect the product to a protected circuit
sure the product has
electrocution or fire.
Never connect the product to
if the rheostat or dimmer channel serves only as a 0~100% switch.
Disconnect the product from power before replacing the fuse.
1. Using a flat-head screwdriver, unscrew the fuse holder from the back of the product.
2. Remove the blown fuse from the holder and replace wi th a fuse of the exact same
type and rating.
3. Insert the fus e holder ba ck in place, re-tighten, and reconnect power.
The product provides power linking via the Edison outlet l ocated in the back
Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 6 I ntimidator™ Spot LED 150 unit
12 Intimidator™ Spot LED 150 units on 230 VAC.
version of the product ONLY! If using the product
requirements may differ in your area.
Intimidator™ Spot LED 150 User Manual Rev. 8 Page 7 of 18
Page 8
Mounting
Orientation
may be mounted in any position; however, make sure
Mount the
appropriate
surface mounting. When
Rubber Feet (x4)
Safety Loop
Point
Bracket
Attachement (x2)
Before mounting the product, read and follow the Safety Notes.
The I ntimidator™ Spot LED 150
adequate ventilation is provided around the product.
Rigging
• Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming purposes.
• Make su re th at th e str uctur e or surface onto which you are mounting the product
can support the product’s weight. See th e Technical Specifications
sec tion of thi s
manual for w eight infor mation.
• When mounting the product overhead, always use a safety cable.
product securely to a rigging p oint , whether an elevated platf or m or a t russ.
• When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has 13 mm holes, which are
for this purpose.
• When power linking multiple products, you must al way s cons id er th e leng th of th e
power linking cable and mount the products close enough for th e cable to reach.
• The rubber feet also serve as floor supports/allow for
mounting the product on the floor, make sure that t he product and c a bl es ar e away
fr om peop le and vehicl es.
Mounting Diagram
Attachment
Page 8 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Page 9
Control Panel
To access the control panel functions, use the four buttons located underneath the
<UP>
Press t o scrol l up t he li st of opti ons or t o fin d a higher v alue
<ENTER>
Menu Map
Mode
Programming Steps
Description
NASL (SLoU)
NAFA (FASt)
Automatic mode, fast program
Normal Pan
PAn
Inverse Tilt
r tiL
Normal
Display
Pan 360
PA36
Tilt 180
Ti18
Tilt 90
Ti 9
4. OPERATION
Operation
display.
Button Function
<MODE/ESC>
<DOWN> Press t o scrol l down the list of options or to fi nd a low er value
DMX Mode 001-512 Sets th e DMX st arting addres s
Operating
Mode
Pan
Tilt
Display
Channel Mode
Manual Pan
Range
Manual Tilt
Range
Press to find an operation mode or to back out of the current menu
option
Press t o activate a menu option or a selected value
SLAv (Son) Slave operating mode
Automatic mode, slow program
NStS (SrUn) Sound-Active mode
Normal Pan operation
Inverse Pan r PAn Inverse Pan operation
Normal Tilt tiL Normal Tilt operation
Inverse Tilt operation
Display
Inverse
11-Channel
Mode
6-Channel
Mode
Pan 540 PA54
Pan 180 PA18
Tilt 270 Ti27
diS
Change the LCD display text position
r di S
11CH
Selects th e D M X pers onality
6CH
Select P an angle range
Select T ilt angle range
Reset rESt Res ets fixt ure
Load LoAd Load factory defaults
Intimidator™ Spot LED 150 User Manual Rev. 8 Page 9 of 18
Page 10
Configuration
the selected DMX mode uses. I f you choose a starting address that is too high, you could
channel DMX
channel personality and
Set the product in DMX mode t o control with a D M X cont rol ler.
(DMX)
1. Connect the product to a suitable po w er outlet .
2. Turn the product on.
3. Connect a DMX cabl e from the DMX out put of the DMX controll er to the DMX input
socket on the product.
Starting Add ress
DMX
Personalities
Wh en selec ting a s tart ing DMX addres s, alw ays co nsider the num ber of DMX channels
restrict the access to some of the product ’s channels.
The Intimidator™ Spot LED 150 uses up to 11 DMX channels in its 11mode, which defines the highest configurable address to 502.
If unfamiliar with the DMX, download the DMX Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MODE/ESC> repeatedl y until 001 shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to sel ect t he st arting addres s.
4. Press <ENTER>.
The Intimidator™ Spot LED 150 has two DMX personalities, a 6an 11-channel personality.
To choose which DMX personality to use, follow the steps below:
1. Press <MODE/ESC> repeatedly until either 11CH (to choose the 11-channel
personality) or 6CH (to choose the 6-channel personality) shows on the display.
2. Press <ENTER>.
Page 10 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Page 11
DMX Channel Assignments and Values
1
Pan
000 ó 255
0–540°
2
Tilt
000 ó 255
0–270°
3
Fine Pan
000 ó 255
Fine control of pan ni ng
4
Fine Tilt
000 ó 255
Fine control of tilti ng
5
Speed
000 ó 255
Pan/Tilt speed ( fast to slow)
000 ó 005
White
006 ó 011
Yellow
012 ó 017
Magenta
018 ó 023
Green
024 ó 029
Red
030 ó 035
Cyan
036 ó 041
Orange
042 ó 047
Blue
048 ó 053
Light Green
054 ó 063
Amber
064 ó 069
White + Yel l ow
070 ó 075
Yellow + M ag ent a
076 ó 081
Magenta + Green
082 ó 087
Green + Red
088 ó 093
Red + Cyan
094 ó 099
Cyan + Orange
100 ó 105
Orange + Blue
106 ó 111
Blue + Light Green
112 ó 117
Light Green + Amber
118 ó 127
Amber + White
128 ó 191
Color cycling rainbow with increasing speed
Reverse color cycling rainbow with increasing
speed
000 ó 003
Blackout
004 ó 007
Open
008 ó 215
Strobe (0–20 Hz)
216 ó 255
Open
8
Dimmer
000 ó 255
0–100%
11-CH
Channel Function Value Setting
6 Color Wheel
7 Shutter
192 ó 255
Intimidator™ Spot LED 150 User Manual Rev. 8 Page 11 of 18
Page 12
11-CH
064 ó 071
Gobo 9 shake, from slow to fast
072 ó 079
Gobo 8 shake, from slow to fast
080 ó 085
Gobo 7 shake, from slow to fast
086 ó 091
Gobo 6 shake, from slow to fast
092 ó 097
Gobo 5 shake, from slow to fast
098 ó 103
Gobo 4 shake, from slow to fast
104 ó 109
Gobo 3 shake, from slow to fast
110 ó 115
Gobo 2 shake, from slow to fast
116 ó 121
Gobo 1 shake, from slow to fast
122 ó 127
Open
128 ó 191
Cycl e effec t with increasing speed
192 ó 255
Reverse cycle effect with increasing speed
000 ó 007
No function
008 ó 027
Blackou t w hi l e pan/ t ilt moving
028 ó 047
Blackout while moving gobo wheel
048 ó 067
Disable blackout while pan/tilt/movi ng gobo wh eel
068 ó 087
Blackout while moving color wheel
088 ó 107
Disabl e blac k out while pan/tilt/ m ovi ng color wh eel
108 ó 127
Disable blackout while moving gobo/color wheel
128 ó 147
Disabl e blac k out while m ovi ng all opti ons
148 ó 167
Reset pan
168 ó 187
Reset tilt
188 ó 207
Reset color wheel
208 ó 227
Reset gobo wheel
228 ó 247
Reset all channels
248 ó 255
No function
000 ó 007
No function
008 ó 023
Automatic movement 1
024 ó 039
Automatic movement 2
040 ó 055
Automatic movement 3
056 ó 071
Automatic movement 4
072 ó 087
Automatic movement 5
088 ó 103
Automatic movement 6
104 ó 119
Automatic movement 7
120 ó 135
Automatic movement 8
136 ó 151
Sound-active movement 1
152 ó 167
Sound-active movement 2
168 ó 183
Sound-active movement 3
184 ó 199
Sound-active movement 4
200 ó 215
Sound-active movement 5
216 ó 231
Sound-active movement 6
232 ó 247
Sound-active movement 7
248 ó 255
Sound-active movement 8
Channel Function Value Setting
(cont.)
9 Gobo Wheel
10 Control Functions
11 Movement Macros
Page 12 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Page 13
1
Pan
000 ó 255
0–540°
2
Tilt
000 ó 255
0–270°
000 ó 005
White
006 ó 011
Yellow
012 ó 017
Magenta
018 ó 023
Green
024 ó 029
Red
030 ó 035
Cyan
036 ó 041
Orange
042 ó 047
Blue
048 ó 053
Light Green
054 ó 063
Amber
064 ó 069
White + Yel l ow
070 ó 075
Yellow + M ag ent a
076 ó 081
Magenta + Green
082 ó 087
Green + Red
088 ó 093
Red + Cyan
094 ó 099
Cyan + Orange
100 ó 105
Orange + Blue
106 ó 111
Blue + Light Green
112 ó 117
Light Green + Amber
118 ó 127
Amber + White
128 ó 191
Color cycling rainbow with increasing speed
Reverse color cycling rainbow with increasing
speed
000 ó 003
Blackout
004 ó 007
Open
008 ó 215
Strobe (0–20 Hz)
216 ó 255
Open
5
Dimmer
000 ó 255
0–100%
064 ó 071
Gobo 9 shake, from slow to fast
072 ó 079
Gobo 8 shake, from slow to fast
080 ó 085
Gobo 7 shake, from slow to fast
086 ó 091
Gobo 6 shake, from slow to fast
092 ó 097
Gobo 5 shake, from slow to fast
098 ó 103
Gobo 4 shake, from slow to fast
104 ó 109
Gobo 3 shake, from slow to fast
110 ó 115
Gobo 2 shake, from slow to fast
116 ó 121
Gobo 1 shake, from slow to fast
122 ó 127
Open
128 ó 191
Cycle effect with increasing speed
192 ó 255
Reverse cycle effect with increasing speed
6-CH
Channel Function Value Setting
3 Color
192 ó 255
4 Shutter
6 Gobo Wheel
Intimidator™ Spot LED 150 User Manual Rev. 8 Page 13 of 18
Page 14
Configuration
standalone mode may transmit DMX signals that could interfere with the DMX
Active
Automatic Mode
Manual Pan/Tilt
Spot LED 150 to operate with normal tilting
Pan/Tilt Angle
Spot LED 150 to
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable po w er outlet .
2. Turn the product on.
Never connect a product that is operating in a ny standalone mode (either Static,
Automatic, or Sound) to a DMX stri ng connected to a DMX controller. Products in
signals from the controller.
Sound-
Operation
Mode
Range
To enable the Sound-Active mode, do the following:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
NASL, NAFA, NStS, or SLAv.
2. Press <UP> or <DOWN> to sel ect NStS.
3. Press <ENTER>.
The product will only respond to low frequencies of music (bass and drums).
To enable the Automatic mode, follow the instructions below:
1. Press <MODE/ESC> repeatedly until one of the following shows on the display:
NASL, NAFA, NStS, or SLAv.
2. Press <UP> or <DOWN> to sel ect NASL (for a slow light show) or NAFA (f o r a fast
light show).
3. Press <ENTER>.
To s elect whether you wa nt th e Intimidator™ Spot LED 150 to operate with normal
panning or inverted panning, do the following:
1. Press <MODE/ESC> repeatedl y until PAn shows on the display.
2. Press <UP> or <DOWN> to select normal pan operation (PAn) or inverse p an
operation (r PAn).
3. Press <ENTER>.
To s elect whether you wa nt th e Intimidator™
or inverted tilting, do the following:
1. Press <MODE/ESC> repeatedl y until tiL shows on the display.
2. Press <UP> or <DOWN> to select normal pan operation (tiL) or inverse pan
operation (r tiL).
3. Press <ENTER>.
You are able to restrict the pan and tilt angles on the Intimidat or™
ach ieve the effect yo u lik e.
To select which pan angle range to use, do the followin g:
1. Press <MODE/ESC> repeatedl y until PA54 shows on the display.
2. Press <UP> or <DOWN> to select 540° (PA54), 360 ° (PA36) or 180° (PA18).
3. Press <ENTER>.
To select which tilt range to use, do the foll owi ng:
1. Press <MODE/ESC> repeatedl y until Ti27 shows on the display.
2. Press <UP> or <DOWN> to sel ect ei ther 270 ° (Ti27), 180° (Ti18) or 90° (Ti 9).
3. Press <ENTER>.
Page 14 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Page 15
Display
Master/Slave
units (the “slaves”)
without the need of a DMX controller. The master unit will be set to operate in either
unison with the master
all the slave units before connecting the master unit to the DMX
Never connect a DMX controller to a DM X string configured for Master/Slave
may interfere with the signals from the
You are able to flip the LED display for easy readability in any mounting situation.
Orientation
To s elect your displa y angl e:
1. Press <MODE/ESC> repeatedl y until diS shows on the display.
2. Press <UP> or <DOWN> to sel ect nor mal display mode (diS) or inverse display
mode (r diS).
3. Press <ENTER>.
The Master/Slave mode allows a single Intimidator™ Spo t LED 150 unit (the “master”) to
Mode
control the actions of one or more Intimidator™ Spot LED 150
Automatic or Sound-Activ e mod e, whil e the s lav e units will be set to op erat e in Sl ave
mode. Once set and connected, the slave units will operate in
unit.
Configure the units as indicated below.
Slave un its:
1. Press <MODE/ESC> repeatedl y until SLAv shows on the displ ay.
2. Press <ENTER> to accept.
3. Set th e DMX address to 001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave uni t.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set th e m aster unit to opera te i n either Automa t ic or Sound mode.
2. Make the master unit the first unit in the DMX daisy chain.
• Configure
daisy chain.
•
operation because the controller
master unit.
• Do not connect more than 31 sl ave units to the master unit.
Reset Software
To reset t he so f tware on t he Intimidator™ Spot LED 150, do the following:
1. Press <MODE/ESC> repeatedl y until rESt shows on the display.
2. Press <ENTER>. The product will reset all settings in the software to the default
factory settings.
Intimidator™ Spot LED 150 User Manual Rev. 8 Page 15 of 18
Page 16
Product
can cause overheati ng. Thi s can
5. TECHNICAL INFORMATION
Dust build up reduces light output perf ormance and
Maintenance
lead to reduction of the light s ource’s life and/or mechanical wear. To m aint ain optimum
performance and minimize wear, you should clean your lighting products at lea st twice a
month. However, be aware that usage and environmental conditions could be
con tributing fact ors to increase the cleaning frequency.
To clean the product, follow the instructions below:
• Unplug the product from po w er.
• Wait until the product is at room temperature.
• Use a vacuum (or dry compressed air) and a s oft brush to rem ove dust coll ected on
the external surface/vents.
• Clean all ext erna l optic s with a mild soap solution, ammonia-free glass cleaner, or
isopropyl alcohol.
• Apply the solution directly to a soft, lint-free cotton clot h or a lens cleaning tissue.
• Softly drag any dirt or grime to the outside edges of the external optics.
• Gently poli sh the external optics until they are free of haze a nd lint.
Alw ays dry th e external optics carefully after cleaning them.
Do not spin the cooling fan/fans using compressed air because you could damage
it/them.
Page 16 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
Page 17
Dimensions and
Length
Width
Height
Weight
8.1 in (205 mm)
8.3 in (211 mm)
11.5 in (291 mm)
9.3 lbs (4.2 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
88 W
92 W
Operating
0.7 A
0.4 A
Power linking current (units)
8 A (6 units)
8 A (12 units)
Fuse
F 2 A, 250 V
F 2 A, 250 V
Power I / O
US/Worldwide
UK/Europe
Power input connector
IEC
IEC
Power output connector
Edison
IEC
Power Cord plug
Edison (US)
Local plug
Light Source
Type
Power
Lifespan
LED
25 W
50,000 h ours
Color
Quantity
Current
White
1
1.5 A
Photo Optic
Parameter
Illuminance @ 2 m
4300 lux
Beam angl e
15º
Stro be r ate
0–20 Hz
Pan & Tilt
540°
270°
Pan/Tilt Ranges
540°, 360°, 180°
Pan
270°, 180°, 90°
Tilt
Thermal
Maximum External Temp.
Cooling Syste m
104° F (40° C)
Fan
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
6, 11
Ordering
Product Name
Item Code
Item Numb er
Intimidator™ S p ot LE D 150
08010176
INTSPOTLED150
6. TECHNICAL SPECIFICATIONS
Weight
Intimidator™ Spot LED 150 User Manual Rev. 8 Page 17 of 18
Page 18
s to
Returns
Tech Support office and request a Return
. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
, in its original box, and with its original packing
the following information on a piece of paper
properly. Any shi pping damage resulting from inadequate
reserves the right to use its own discretion to repair or replace
Contact Us
Fax: +44 (0)1773 511110
Email: tech@chauvetlighting.com
www.chauvetlighting.com
www.chauvetlighting.co.uk
In case y ou need to return a product or request s upport, follow the procedure below:
• If y ou li ve in t he U.S., contact CHAUVET® World Headquarters (see below).
• If you live in the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
• If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your
distributor of record. See www.chauvetlighting.com
for distributors outside the U.S.,
United Kingdom, or Ireland.
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® product
them. Visit our website for contact details.
Call the corresponding CHAUVET®
Merchandise Authorization (RMA) number before shipping the product
return.
You must send the merchandise prepaid
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NO T wr i t e th e RM A number
directly on the box.
Before sending the product, clea rly wr ite
and place it inside the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be su re to p ack th e product
packaging will be your responsibility. As a suggestion, proper UPS packing or doubleboxing is always a safe method to use.
CHAUVET®
returned product(s).
World Headquart ers
CHAUVET®
General Inform ation
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: (954) 577-4455
Fax: (954) 929-5560
Toll free: (800) 762-1084
Technical Support
Voice: (954) 577-4455 (Press 4)
Fax: (954) 756-8015
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Inform ation
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: +44 (0)1773 511115
Technical Support
Email: uktech@chauvetlighting.com
World Wide Web
Page 18 of 18 Intimidator™ Spot LED 150 User Manual Rev. 8
World Wide Web
Loading...