Charnwood C4, C-FOUR Operating & Installation Instructions Manual

Operating & Installation Instructions

charnwood

®

C O N T E N T S

O P E R AT I NG I N S T R U CT I O N S

Fuel

Fitting The Riddling Grate

Lighting

Refuelling

Ash Clearance

Reduced Burning

Cleaning and Maintenance

Throat Plate & Flueway Clearing

Chimney Sweeping

Servicing

Trouble Shooting

CO Alarm

If you need further help

Health & Safety Precautions

CO Alarms

Specification

Chimney

Hearth & Fire Surround

Connection to Flues

Soot Doors

Pre Lighting Check

Commissioning

Clean Air Act Information

Dimensions

Parts Lists

Certification

4

4

5

5

5

6

6

6

6

6

7

7

7

9

10

11

11

11

11

12

13

14

INS TALLAT ION I NSTRUCT ION S

5

9

9

9

9

Controlling The Fire

Ref. C-FOUR v1 09.11

Tools required for fitting the riddling grate:

10mm Spanner
Pozidrive screwdriver

Before fitting the riddling grate (Fig. 1) remove the fuel retainer and

the wood ash retainer. The wood ash retainer is not required when

the riddling grate is fitted.

Undo the nut on the riddling blanking hole using a 10mm spanner.

Remove the cover and spacing washer (ensure you keep these in a

safe place as you will need to replace them if the riddling grate is

removed).

Feed the riddler rod through the hole on the right hand side of the

stove, and slide one washer onto the rod. (If there is not sufficient

room to the right of the stove to do this then remove the riddler

knob, fit one washer over the rod and then slide the rod through the

hole from the inside of the stove.)

Feed the rod through the two side fireplates and slide the other

washer on to the rod so that the washers end up outside the two side

fireplates. With the side fireplates pushed together fit the retaining

clips so that the washers come inside the clips.

Slide the side fireplates apart so that they rest against the sides of the

firebox. Slot in the front and rear support plates.

Fit the grate plates into position through the front and rear grate

support plates, making sure they locate correctly onto the riddler

rod. Fit the fuel retainer. Slide the ashpan under the grate.

Before lighting the stove check with the installer that the work and

checks described in the Installation Instructions have been carried out

correctly and that the chimney has been swept, is sound and free

from any obstructions. The stove is not suitable for use in a shared

flue system.

Remember that the stove will be hot and that it is made from hard

materials – ensure that you have good balance before operating the

fire.

Do not use an aerosol spray on or near the stove when it is alight.

There is a risk of explosion or flash ignition of the spray.

The stove is suitable for intermittent operation.

This stove has been designated to burn wood. Only dry, well

seasoned wood should be burnt on this appliance as burning wet

unseasoned wood will give rise to heavy tar deposits in the stove, on

the glass and within the chimney. For the same reason hard woods

(such as Ash, Beech and Oak) are better than soft woods (such as

Pine and Spruce). Burning wet unseasoned wood will also result in

considerably reduced outputs.

The wood should be cut and split and then left to season in a well

ventilated dry place for at least one year but preferably two years

before use. Approximate suitable log sizes are 255mm (10in) long

and 75mm (3in) diameter.

This stove is not designed to burn household waste.

For advice on other fuels please contact Charnwood.

This appliance has been approved by HETAS as an intermittent

operating appliance for burning dry seasoned wood logs only. HETAS

approval does not cover the use of other fuels either alone or mixed

with wood logs nor does it cover the instructions for use of other

fuels.

PETROLEUM COKE IS NOT SUITABLE FOR USE ON

THIS APPLIANCE. ITS USE WILL INVALIDATE THE

GUARANTEE.

When using the stove in situations where children, aged and/or

infirm persons are present a fireguard must be used to prevent

accidental contact with the stove. The fireguard should be

manufactured in accordance with BS 8423:2002.

FUE L

FIT T ING THE R IDDLI N G GRATE

®

OPERATING INSTRUCTIONS

4

Fig.1. Optional Grate Kit

Front Grate
Support

RH Side Grate
Support

Grate Plates

Rear Grate
Support

Riddler
Rod

Ashpan

LH Side Grate
Support

LIG H TING

CON T ROLL ING THE F IRE

On initial lighting, the stove may smoke and give off an odour as the

silicon paint with which the firebox is painted reacts to the heat. This

is normal and will cease after a short time, but meanwhile the room

should be kept well ventilated.

At first only light a small fire and burn it slowly for two hours to allow

any residual moisture in the chimney to evaporate.

Light the stove using dry kindling wood and paper or fire lighters. Put

the paper, or fire lighters, and kindling in the firebox and cover with a

few small dry logs. Open the air control fully (see Fig. 2) Light the

paper or fire lighters. The door may be left cracked open for a few

minutes to assist the combustion and heat up the firebox more

quickly. When the kindling wood is well alight add a few more small

logs and close the door, but leave the air control fully open. When

the flames are established around these logs, load the stove with the

required fuel load. Maintain the air control at maximum at this stage.

Once the fire is up to temperature the airwash system will begin to

work, so allow the fire to become hot before adjusting the air control

to the required setting. During the lighting period, do not leave the

stove unattended. Do not leave the door open except as directed

above to avoid excessive smoke.

When relighting the stove, leave the ash on the base if burning wood,

unless it is becoming too deep, in which case some of it may be

removed. If burning high ash content fuel, clear the grate and empty

the ashpan before relighting.

The rate of burning and hence the output is controlled by the air

control (see Fig. 2).

Open the air control fully (boost position) when lighting or when

rapid burning is required. It should not be left fully open for long

periods as this can cause over-firing or excessive smoke production.

For high output move the air control to the ‘click position’ or for low

burning to the fully closed position.

When the fire is burning normally the air control gives enough

airwash to keep the glass clean. However, it will not always be

possible to keep the glass clean with the air control fully closed.

Keep the firebox well filled but do not allow fuel to spill over the top

of the fuel retainer.

Logs should be evenly distributed, filling the firebed to give the most

pleasing flame pattern. The air control must be fully opened after

refuelling until the flames are established above the fire. It is best to

refuel on to a hot bed of ash. If at this point the fire starts to die, the

door must be cracked open until the fire is revived. If the fire has

started to die down before refuelling, then more kindling wood must

be added, the air control opened fully and the door cracked open to

re-establish the firebed adding larger logs (see suitable log

sizes in Fuel section). This will avoid excessive smoke emission.

Care should be taken, especially when burning wood, that fuel does

not project over the fuel retainer or damage to the glass may be

caused when the door is closed. It can also cause the glass blackening

of the glass. Maximum filling height is such that logs cannot fall from

the fire when the door is opened. In smoke controlled areas do not

fill the stove above the level of the front firebars, as overloading can

cause excess smoke. Liquid fuels are not to be used on this appliance.

The ashpan should be emptied regularly before it becomes too full.

Never allow the ash to accumulate in the ashpan so that it comes in

contact with the underside of the grate as this will seriously damage

the grate bars. The ashpan is handled using the tool provided. Care

should be taken to ensure that ash is cool before emptying it into

plastic liners or bins.

To make ash removal easier there is a special Charnwood ash carrier

available. This may be purchased from your supplier or, in case of

difficulty, directly from Charnwood.

before

For

correct firing we recommend the use of a stove pipe thermometer

which may be purchased from your supplier or directly from

Charnwood.

REF U ELLIN G

ASH CLEARANCE

5

®

OPERATING INSTRUCTIONS

Fig.2. Stove Controls

Air Control
Pull out to Open
Push in to Close

Door
Handle

Pull to
Open

Low

Output

High

Output

(‘Click’)

Boost

Air Control

positions

RED U CED BUR NING

CLE A NING AN D MAINT E NANCE

THR OAT PLAT E AND

FLUEWAY CLEA NING

For reduced burning the fire door must be closed.

When burning wood in areas that are not smoke controlled, load

some large logs on the fire and allow to burn for half an hour before

closing the air control (this will help to reduce tar deposits in the

chimney). Some experimentation may be necessary to find the setting

most suitable for the type of fuel being used and the draw on the

chimney.

To revive the fire, empty the ashpan, (if burning fuel other than

wood), riddle the fire, and open the air control to maximum. When

the fire is burning well load on more fuel as necessary and adjust the

air control to the desired setting.

The stove is finished with a high temperature paint which will

withstand the temperatures encountered in normal use. This may be

cleaned with a damp lint-free cloth when the stove is cold. Should re-

painting become necessary, high temperature paints are available

from your supplier or from stove shops.

Most deposits on the glass may be burnt off simply by running the fire

at a fast rate for a few minutes. If it becomes necessary to clean the

glass then open the door and allow it to cool. Clean the glass using a

damp cloth and then wiping over with a dry cloth. Any stubborn

deposits on the glass may be removed with a proprietary stove glass

cleaner or ceramic hob cleaner. Do not use abrasive cleaners or pads

as these can scratch the surface which will weaken the glass and cause

premature failure.

It is important that the throat plate and all the stove flueways are kept

clean in order to prevent potentially dangerous fume emission. They

should be cleaned at least monthly, and more frequently if necessary.

It is necessary to let the fire out to carry out these operations.

The front of the throat plate is pulled forward and then lowered as

shown in Fig. 3. Any sooty deposits should then be swept from the

plate and into the fire.

Return the throat plate to its correct position - raise the front of the

plate, push it back and then lower it onto the retaining lugs.

CHIMNEY SWEEPING

SERVIC ING

The chimney should be swept at least twice a year. Where the top

outlet or vertical rear flue connector is used it will generally be

possible to sweep the chimney through the appliance.

First remove the fuel retainer and the throat plate. Then sweep the

chimney ensuring that soot is removed from all horizontal surfaces

after sweeping.

In situations where it is not possible to sweep through the appliance

the installer will have provided alternative means, such as a soot door.

After sweeping the chimney the appliance flue outlet and the flue

pipe connecting the stove to the chimney must be cleaned with a flue

brush.

After clearing any soot from within the stove, replace the throat plate

(see Fig. 3) and the fuel retainer.

Different types of sweep’s brushes are available to suit different

flueways. For standard brick chimneys, a wire centre sweep’s brush

fitted with a guide wheel is recommended. For prefabricated

insulated chimneys the manufacturers instructions with regard to

sweeping should be consulted.

It is recommended that the fire is serviced once a year to keep it in

first class working order. After cleaning out the firebox thoroughly,

check that all internal parts are in good working order, replacing any

parts that are beginning to show signs of wear. Check that the doors

seals are in good condition and that the door seals correctly. A

servicing guide is available on request. Repairs or modifications may

only be carried out by the Manufacturer or their approved agents.

Use only genuine Charnwood replacement parts.

6

®

OPERATING INSTRUCTIONS

Throat Plate

Pull Up
and Swing Down

Fig.3. Throat Plate Position and Lowering

Persistent fume emission is potentially dangerous and must not be

tolerated. If fume emission does persist, then the following

immediate actions should be taken:

a) Open doors and windows to ventilate the room.

b) Let the fire out and safely dispose of the fuel from the

appliance.

c) Check for flue or chimney blockage, and clean if required.

d) Do not attempt to re-light the fire until cause of fume has been

identified. If necessary, seek professional advice.

Fire blazing out of control

Chimney Fires

The most common cause of fume emission is flueway or chimney

blockage. For your own safety these must be kept clean.

Check that:

a) The door is tightly closed.

b) The air control slider is fully closed.

c) A suitable fuel is being used.

d) Door seals and airwash slide are intact.

If the chimney is thoroughly and regularly swept, chimney fires should

not occur. However, if a chimney fire does occur close the air control,

and tightly close the door of the appliance. This should cause the

chimney fire to go out in which case the controls should be kept

closed until the stove has gone out. The chimney and flueways should

then be cleaned. If the chimney fire does not go out when the above

action is taken then the fire brigade should be called immediately.

After a chimney fire the chimney should be carefully examined for

any damage. Expert advice should be sought if necessary.

Your installer should have fitted a CO alarm in the same room as the

appliance. If the alarm sounds unexpectedly, follow the instructions

given under “Warning Note” above.

If you need further help with your Charnwood then your Installer will

be able to provide the answers to most questions. Your Local

Charnwood Premier Dealer has a great deal of experience and will

also be able to provide helpful advice. Further help is available from

the Charnwood Customer Services department who will be pleased

to give advice, if necessary.

CO AL A RM

IF YOU NEED FURTHER HELP

TROUBLE SHOOTING

Fire Will Not Burn

Blackening of Door Glass

Fume Emission

Warning Note:

Properly installed and operated this appliance will not emit fumes.

Occasional fumes from de-ashing and re-fuelling may occur.

Check that:

a) the air inlet is not obstructed in any way,

b) chimneys and flueways are clear,

c) a suitable fuel is being used,

d) there is an adequate air supply into the room,

e) an extractor fan is not fitted in the same room as the stove.

f) there is sufficient draw in the chimney. Once the chimney is warm a

draught reading of at least 2.5 mm (0.10 inches) water gauge (25Pa)

should be obtained.

Differences in chimney draughts mean that the best settings of the air

controls will vary for different installations. A certain amount of

experimentation may be required, however the following points

should be noted and with a little care should enable the glass to be

kept clean in most situations:

a) Wet or unseasoned wood, or logs overhanging the front fence will

cause the glass to blacken.

b) The airwash relies on a supply of heated air to keep the glass clean.

Therefore, when lighting the stove, allow the firebed to become well

established before closing the air control. This may also be necessary

when re-fuelling the stove.

c) When re-fuelling keep the fuel as far back from the front fence as

possible. Do not try to fit too much fuel into the firebox.

d) Do not completely close the air control.

It is always more difficult to keep the glass clean when running the

stove very slowly for long periods.

If blackening of the glass still occurs check that all flue connections

and the blanking plate are well sealed. It is also important that the

chimney draw is sufficient and that it is not affected by down-draught.

When the chimney is warm a draught reading of at least 2.5 mm

(0.10 inches) water gauge (25Pa) should be obtained. Some

blackening of the glass may occur below the level of the fuel retainer.

This will not obscure the view of the fire or affect its performance.

7

®

OPERATING INSTRUCTIONS

HEALTH AND SAFETY PRECAUTIONS

SPE C IFICATI ON

CHI M NEY

Please take care when installing the stove that the requirements of

the Health and Safety at Work Act 1974 are met.

Some types of fire cement are caustic and should not be allowed to

come into contact with the skin. In case of contact, wash with plenty

of water.

If there is a possibility of disturbing any asbestos in the course of

installation then please use appropriate protective equipment.

There must not be an extractor fan fitted in the same room as the

stove as this can cause the appliance to emit fumes into the room.

As the output is below 5kW a permanent air supply is not normally

required. This stove is capable of intermittent operation.

This stove is not suitable for use in a shared flue system.

In addition to these instructions the requirements of BS 8303 and

BSEN 15287-1:2007 must be fulfilled. Local Authority Bylaws and

Building Regulations, including those referring to national and

European Standards, regarding the installation of Solid Fuel burning

appliances, flues and chimneys must also be observed.

Building regulations require that whenever a new or replacement

fixed solid fuel or wood/biomass appliance is installed in a dwelling a

carbon monoxide alarm must be fitted in the same room as the

appliance. Further guidance on the installation of the carbon

monoxide alarm is available in BS EN 50292:2002 and from the

alarm manufacturer's instructions. Provision of an alarm must not be

considered a substitute for either installing the appliance correctly or

ensuring regular servicing and maintenance of the appliance and

chimney system.

The nominal output of the C-FOUR is 4.9 kW (16,700 Btu/h). This

output is based on a 45minute re-fuelling cycle burning seasoned

hardwood logs. The average flue temperature at rated output is

281°C. The Flue gas mass flow is 4.2g/s and the stove weight is

62kg.

In order for the appliance to perform satisfactorily the chimney height

must not be less than 4 metres measured vertically from the outlet of

CO AL A RMS

the stove to the top of the chimney. The internal dimensions of the

chimney should preferably be 175 mm (7 inches) or 200mm (8

inches) either square or round and MUST NOT BE LESS THAN 125

mm (5 INCHES).

If an existing chimney is to be used it must be swept and checked, it

must be in good condition, free from cracks and blockages, and

should not have an excessive cross sectional area. If you find that the

chimney is in poor condition then expert advice should be sought

regarding the necessity of having the chimney lined. If it is found

necessary to line the chimney then a lining suitable for Solid Fuel must

be used.

If there is no existing chimney then a prefabricated block chimney or

a twin walled insulated stainless steel flue to BSEN 15287-1:2007 can

be used either internally or externally. These chimneys must be fitted

in accordance with the manufacturers instructions and Building

Regulations.

Single wall flue pipe is suitable for connecting the stove to the

chimney but is not suitable for using for the complete chimney.

If it is found that there is excessive draw in the chimney then a

draught stabiliser should be fitted.

It is important that there is sufficient draw in the chimney and that

the chimney does not suffer from down-draught. When the chimney

is warm the draw should be not less than 2.5mm (0.10 inches) water

gauge (25 Pa). If in doubt about the chimney seek expert advice.

HEA RTH AND F IRE SUR ROUND

The stove must stand on a fireproof hearth and must not be situated

closer than 600mm from combustible materials to the sides or rear

above hearth level unless adequately fireproofed in accordance with

local building regulations. The hearth must be of fireproof material

and at least 12mm (½ inch) thick. The positioning of the stove and

the size of the hearth are governed by building regulations for Class 1

appliances. These building regulations state that the hearth must

extend in front of the stove by at least 300mm (12 inches) and to the

sides of the stove by at least 150mm (6 inches).

If in

doubt as to the positioning of the stove, expert advice should be

sought either from the supplier or the local building inspector.

The fireplace must allow good circulation of air around the appliance

to ensure that maximum heat is transferred to the room and also to

prevent the fireplace from overheating. A gap of 150mm (6 inches)

each side and 300mm (12 inches) above the appliance should give

When the fire door

is open, it extends beyond the flat front of the stove by 365mm.

9

®

INSTALLATION INSTRUCTIONS

sufficient air circulation. If a wooden mantelpiece or beam is used in

the fireplace it should be a minimum of 460mm (18 inches), and

preferably 600mm (24 inches) from the appliance. In some situations

it may be necessary to shield the beam or mantelpiece to protect it.

In order for the fire to operate correctly and to allow for access,

there must be an air gap behind the appliance of at least 75mm, but

be aware that this distance will need to be greater in some cases to

meet Building Regulation requirements.

CON N ECTIO NS TO FLUES

The stove must be connected to the flue using 125mm (5") i/d pipe.

This may be stainless steel, cast iron, or thick wall steel pipe. Straight

lengths of Charnwood Pipe to match the stove are available if

required.

There are several ways of connecting the stove to the flue. These are

illustrated in Figs. 5 to 8.

If the optional vertical rear flue connector is used then the chimney

may be swept through the appliance.

Horizontal lengths of flue must be kept to a minimum and should not

be more than 125mm (5 inches) long.

The stove comes with the blanking plate fitted to the top flue outlet.

The seal for the outlet is a 180mm dia ring of rope seal. The seal

for the outlet is a length of adhesive backed fibre webbing

supplied with instructions. This is applied to the flue collar or the

Vertical Rear Flue adapter for rear outlet installations. For top outlet

installations, the blanking plate must be removed and the webbing

fitted to its sealing face, then fitted to the rear flue outlet.

top

rear

Ensure that

10

®

INSTALLATION INSTRUCTIONS

Fig. 4. Flue Blanking Plate.

Blanking Plate

Clamping plate finishes
flush with inside face of
firebox top and bottom.

with Glass Fibre Webbing

Seal Blanking Plate

Register Plate

Soot Door

In Side or Rear

Of Chimney

Register Plate
With Soot Door

Alternative

Soot Door Positions

Register Plate

With Soot Door

Alternative

Soot Door Positions

Fig. 5. Vertical Register Plate With Bricked Up Fireplace

Fig. 6. Horizontal Register Plate With Rear Flue Connection

Fig. 7. Horizontal Register Plate With Top Flue Connection

Glass Fibre Webbing

Blanking Plate

Back of Stove

Clamping Plate

M8 Nut

the fold on the clamping plate is in line with the lugs on the firebox as

shown in Fig.4. Ensure that the clamping plate does not prevent the

throat plate from seating correctly. All flue connections must be well

sealed.

It is possible to pass a 16 inch diameter sweep’s brush through the

appliance but in most back outlet installations it will be necessary to

have a soot door to enable the chimney to be swept. The optional

vertical rear flue connector does allow the chimney to be swept

through the stove.

SOO T DOORS

PRE L I GHTIN G CHECK

COM M ISSIO NING

Soot doors may either be in the actual brickwork of the chimney or

in the register plate. Various positions of soot doors are shown in

Figs. 5 to 8.

Ensure that the throat plate is fitted in the roof of the appliance. The

location and positioning of the throat plate is shown in Fig. 3.

Check that the front fence is fitted correctly and that the door closes

properly.

On completion of the installation allow a suitable period of time for

the fire cement and mortar to dry out before lighting the fire. If no

grate is fitted make a layer of ash or sand on the base of the stove

before lighting. Check to ensure that smoke and fumes are taken

from the appliance up the chimney and emitted safely. Also check all

joints and seals. On completion of the installation and commissioning

please leave the operating instructions with the customer and advise

them on the use of the appliance.

Under the Clean Air Act local authorities may declare the whole or

part of the district of the authority to be a smoke control area. It is an

offence to emit smoke from a chimney of a building, from a furnace

or from any fixed boiler if located in a designated smoke control area.

It is also an offence to acquire an "unauthorised fuel" for use within a

smoke control area unless it is used in an "exempt" appliance

("exempted" from the controls which generally apply in the smoke

control area).

The Secretary of State for Environment, Food and Rural Affairs has

powers under the Act to authorise smokeless fuels or exempt

appliances for use in smoke control areas in England. In Scotland and

Wales this power rests with Ministers in the devolved administrations

for those countries. Separate legislation, the Clean Air (Northern

Ireland) Order 1981, applies in Northern Ireland. Therefore it is a

requirement that fuels burnt or obtained for use in smoke control

areas have been "authorised" in Regulations and that appliances used

to burn solid fuel in those areas (other than "authorised" fuels) have

been exempted by an Order made and signed by the Secretary of

State or Minister in the devolved administrations.

The has been recommended as suitable for use

in smoke control areas when burning wood logs.

Further information on the requirements of the Clean Air Act can be

found here: http://smokecontrol.defra.gov.uk/

Your local authority is responsible for implementing the Clean Air Act

1993 including designation and supervision of smoke control areas

and you can contact them for details of Clean Air Act requirements.

CAA AN D SMOKE CO NTRO L

The Clean Air Act 1993 and Smoke Control Areas

Charnwood C-FOUR

11

®

INSTALLATION INSTRUCTIONS

Register Plate
With Soot Door

Alternative

Soot Door Positions

Fig. 8. Horizontal Register Plate With Optional
Vertical Rear Flue Connector

®

C-FOUR DIMENSIONS (mm)

12

763

710

608

194.5

64.5 OD

458

62 ID

44.5

Dimensions of the

Optional Vertical

Rear Flue Connector

140 i/d to suit 125mm (5")

flue pipe

Issue K

19

®

char n w ood BI SH OPS WAY, NEWPORT, IS LE OF WIGHT PO3 0 5W S, U NI TED KINGDOM

T: [phone] • F:+ 44 (0 )19 83 53 77 88 • SP AR ES@ CH AR NWO OD. CO M • WW W.CH AR NWO OD .C OM

®

C-FOUR PART S L I S T

Item Part No. Description

1# 002/BR001/A Door Assembly
2 008/FFW026 1/4 Heavy Brass Washer
3 006/PV19 Glass (inc seal)
4 008/BR014 Handle Pivot Pin
5 004/BW23 Glass Retainer
6 008/FFS018 M6x16 C'sunk Skt Hd Screw
7 008/PV21 Rope Door Seal
8 004/BR005 Air Box Control Plate
9 004/BR007 Air Inlet Slide
10# 001/BR010 Firebox
11 004/BR016 Control Rod
12 002/BR017 Fuel Retainer BR
13 010/BR031 Throat Plate
14 010/BR029 RH Sideplate
15 010/BR030 Inner Backplate
16 004/BR040 Airbox Cover
17 002/DY21 Riddler Knob
18 008/BR044 Gasket Blanking Plate
19 008/BR006 Gasket Airbox
20 008/FFB034 M8 Nyloc nut
21 012/BR011 Serial No. Label
22 002/PV13 Door Latch
23 008/FFW025 M8 Wavy Washer
24 008/FFW007 3/8" Plain Light Washer
25 008/FFS050 M8 Bolt 30mm Long
26 008/AY37 Air Control Knob
27 002/BR034 Wood Ash Retainer
28 008/BR045 Air Box Gasket

34 008/FFS025 M6 x 12 Bright Pozi Pan Hd
35 008/BR047 Back Gasket
36 008/FFS059 M8 x 20 Hex Hd Bolt
37 008/BR052 Felt Washer
38 011/PV26 Side Gasket
39 004/BR053 Air Inlet Spigot assy
40 004/BR054 Blanking Plate
41 004/DY22 Riddler Blanking Disk
42 010/EY12 Serial Number Hanger Bracket
43# 010/PV33 Vert Rear Flue Adaptor
44 002/PV12B Flue Collar
45 012/PV09 Blanking Plate
46 002/BR020 Hinge
48 004/BR033 Ashpan
49 002/EY03 Grate Plate
50 010/EY04 L.H. Grate Support
51 010/EY05 R.H. Grate Support
52 010/EY06 Front Grate Support
53 010/BR035 Rear Grate Support
54 010/EY13 Riddler Rod Assy
55* 008/PV55 Glass Seal
56* 008/FW29 Door Seal Adhesive
57# 002/BR012 Handle Casting
58 004/BR015 Clicker Retainer Plate
59 008/ES36/01 Brass Ball Catch
60 010/BR022 Grate Kit
61* 010/EW51 Ash Carrier (Optional Extra)
62 008/BW39/S Hinge Pin Set
63 008/FFW015 Spring Washer (Thackery Type)
64 008/FFB007 M8 x 100mm Allen Head Bolt
65# 010/BR050 Store Stand
66* 010/BR057 Heat Shield

29 010/BR028 LH Sideplate
30 008/BR012 Wooden Handle
31 008/FFS003 Pan Head Screw M5 x 10
32 008/FFS078 Pozi Pan Head 4.2 x 9.5
33 008/FFB003 Coach Bolt M6 x 20

(Optional Extra)

Item Part No. Description

To obtain spare parts please contact your local stockist giving Model, Part No. and
Description. In case of difficulty contact the manufacturer at the address shown.

* These items are not shown on the drawing.
# Please specify colour when ordering.
This drawing is for identification purposes only.

17

52

50

48

51

53

49

68

60

54

Optional Grate Kit

14

15

13

46

12

27

22

5

333145

21

34

19

8

9

16

18

4025 11 17 26

28

37

29

32

42

43 44

32

20

24

23

7

30

1

2

3

6

10 35

58

59

57

38

38

36

62

41

65

6364

67

4

39

14

EN13240:2001

ROOMHEATERS FIRED BY SOLID FUEL

EC certificate of
conformity no:

Fuel types:

Minimum distance to
combustible materials:
Side:
Rear:

Emission of CO in
combustion products:

Flue gas temperature:

Space heating thermal
output:

Energy efficiency:

A Division of A .J.Wells & Sons Limited Registered in England No. 03809371

11

Bishops Way, Newport, Isle of Wight PO30 5WS, United Kingdom

A.J WELLS & SONS LTDA.J WELLS & SONS LTD

BR080-CPD-2011

600 mm
600 mm

0.18%

281°C

4.9kW

78.3%

Wood Logs

A D i v i s i o n o f A . J . W e l l s & S o n s L i m i t e d R e g i s t e r e d i n E n g l a n d N o . 0 3 8 0 9 3 7 1

char n w ood BI SH OPS WAY, NEWPORT, IS LE OF WIGHT PO3 0 5W S, U NI TED KINGDOM

T:+ 44 (0)198 3 537 777 • F :+ 44 (0) 198 3 5377 88 • CH ARNWO OD @AJWELL S.CO.UK • WWW.CH ARN WOO D. CO M

y ou r p re m ie r d e al e r

REV.C-FOUR v1 08.

11

®