Page 1
INSTRUCTION MANUAL
3PCS Cast Aluminum Bistro Set
Page 2
INTRODUCTION
Thanks for purchasing and trusting us with your home
decorating plans.
· Only need to rinse it thoroughly with clean water to wash
away dirt and grime. Never use abrasive cleansers on the furniture, since it can attack the surfaces and leave behind scratch
marks.
· For the stubborn grime and stains, just use a soft sponge and
mild soapy water and then dry it with a cloth or paper towel.
· Check the stability of the screws, nuts and nut caps prior to
each use. If necessary, tighten all of them again to ensure it is
secure.Tighten up them after one to two month’s use whenever required.
· Place the furniture on an even, sturdy surface.
We are committed to R&D innovation and to create the most
refined, diverse choice of outdoor collection.
After unpacking and before every use, check whether the item
shows any damages. In addition, check that you have all parts and
hardwares before assembly. If there is any damage, please do not
use and just call customer service or send an email. If you do not
have all the parts lists, have your dealer contact us and they
will be sent to you immediately.
This furniture is intended for indoor and outdoor use. Please take
time to read and follow the instruction below. Use the item as
described in this operating manual.We accept no liability for damages caused by improper use.
· Avoid improper use, and be careful not to scratch or damage
the surface with sharp objects.
· When you move your furniture, make sure you lift it rather
than pulling or pushing it to avoid damaging the floor, legs and
mounting.
CUSTOMER SERVICE
Thanks for purchasing this furniture. We are here to help you
maximize your enjoyment and appreciation of it.
Please do not hesitate to contact our customer service when
you have any questions regarding assembly or accessories.
1 6
Page 3
ASSEMBLY INSTRUCTIONS
Part
Number
D
Images
and
Sizes
Stud M8*35
Qty.
3
1. Place all parts on a clean soft
surface.
2.Attach the front and back Legs
(C,D) to the studs on the
chair seat (B) using washers and
nuts (L,M,N).Tighten the nuts using
the wrench & tighten.
Add the protect hats (P).
3. Attach the backrest (A) to the
chair seat (B) using washers and
nuts (L,M,N).Tighten the nuts using
the wrench .Add the protect
hats (P)
4. Attach the right and left
arm(E,F) using the bolts (G)
and washers ,nuts (H,I,J) .DO NOT
over tighten .And then using bolts
(K) and washers and nuts (H,I,J).
Adjust to a correct place ,
then tighten G&K.Add the protect
hats (O).
5.Adjust the pre-installed rubber
pad (I) until the chair is level with
the ground .
Upon completion of full assembly
and bolted up-all screws can be
tightened down.
D E F G
H I J K
List of Parts for Assembly of 1x Table
No
A
B
C
M
M8 protect hats
M8 Flat washer
Parts
Table Top
Table Leg
Leg Support
E F
M8 Spring washer
E
F
G
H
I
J
K
L
M
M8 Flat washer
M8 Spring washer
M8 Nuts
M6*30 Stud
M6 Flat washer
M6 Spring washer
M6 Nuts
M6 protect hats
M8 protect hats
Qty
1
3
1
Wrench
Screwdriver
3
3
3
6
6
6
6
6
3
CARE AND MAINTENANCE
With a little care you can prolong the life of your furniture. Follow the
instruction for the materials of your special product to make sure that it
stays in the best shape for as long as possible.
The information below is only intended as a general guideline. For
more information, please enquire where you bought the furniture.
5 2
L
M6 protect hats
M8 Nuts
G
I J K
M6 Flat washer
M6 Spring washer
M6 Nuts
D
Stud M8
H
M6*30 Stud
Page 4
ASSEMBLY INSTRUCTIONS
Part
Number
G
H
I
Images
and
Sizes
M6*30 Stud
M6 Flat washer
M6 Spring washer
Qty.
4
12
12
1.Place all parts on a clean soft
surface.
2.Place the table top (A) upside
down.Attach the table legs on
the table top (B) using the studs
(D),washers and nuts(E,F,G).
Tighten the nutsusing the a wrench,
DO NOT over tighten
3. Attach the leg support (C) to
the table legs (B) using bolts
(H),washers and nuts (I,J,K).
4.Tighten all the nuts using the
wrench . And add all the protect
hats (L,M)
5.Adjust the pre-installed rubber
pad , at the end of each table
legs until the table is level with
the ground.
No
A
B
C
D
E
F
M8 protect hats
P
O
M6 protect hats
Parts
Backrest
Chair Seat
Front Chair Legs
Back Chair Legs
Right Arm
Left Arm
M8 Flat washer
L M
M8 Nuts
N
H I J
M6 Flat washer
M6 Spring washer
M8 Spring washer
M6 Nuts
J
K
L
M
N
O
P
M6 Nuts
M6*25 Stud
M8 Flat washer
M8 Spring washer
M8 Nuts
M6 protect hats
M8 protect hats
Qty
2
2
4
4
2
2
Wrench
Screwdriver
K
M6*25 Stud
G
M6*30 Stud
12
8
20
20
20
12
20
3 4
Loading...