Assembly Instruction Sheet
ToolsRequired: Flathead screwdriver, Phillips screwdriver,pliers, wire cutters, wire strippers,electrical tape, safety glasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.If any parts are missingor damaged, do not attemptto assemble, install, or operatethe fixture. Contact customer servicefor replacement
parts.
Fixturecan only be mounted inthe direction indicated on page2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(1)A19 MediumBasebulb 100W Maximum.
20-30minutes
Identifyand inspect all parts beforebeginning installation. Check package contentlist and diagrams below toensure all parts are
Package Contents
Crossbar Assembly
A
x1
Alternate
Mounting screw
B
x2
STEP 1 - Insert Glass Panels
A. Insert the U-shaped foam end of the
Glass Panel (D) into the slot in the
bottom of the cage and fasten with
the tabs in the top edge of the cage.
Figure 1
STEP 2 Installing the CrossbarAssembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use theAlternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Outlet
Box
Mounting Screw
or Alternate Short
Mounting Screw
A
Figure 2
Fixture Body
C
x1
Glass Panel
D
x4
Outlet Box Screws
(not included)
Supply Wires
with Ground Wire
C
Tab
Slot
D
U-shaped
Foam
.
STEP 3 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw
or alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting
screws or alternate short
mounting screws in or out
of the crossbar until the
correct length is
achieved. Once the
backplate and Fixture
Body (C) is secure,
remove the mounting ball
and Fixture Body (C) and
proceed to Step 4.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Bare, or Green
Ground wire
from outlet box
Mounting Screw
or Alternate Short
Mounting Screw
Hex Nut and
Lock Washer
Backplate
Figure 3
OR
Green Ground Screw
on the Crossbar
Figure 4
Mounting Ball
A
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Ground wire
from fixture
C
Thank you for purchasing product.
1of2
STEP 5 Install the Fixture Body-
A. Position the backplate and Fixture Body (C) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
screws or alternate short mounting screws. Secure the Fixture Body
by using the mounting balls and hand tighten the mounting balls
until snug.
Mounting Screw
Mounting Ball
or Alternate Short
Mounting Screw
C
A
Figure 5
Backplate
STEP 6 - Install the Bulb and Apply Silicone Sealer
A. Insert the bulb onto socket and screw snugly into place.
B. Make sure the exterior wall surface and fixture backplate are free of
dirt before applying caulk. Using exterior grade caulk, caulk over
top of backplate and down both sides. Do not caulk the bottom of
the fixture backplate to
ensure proper moisture
drainage.
Exterior
Grade Caulk
Your fixture is now
assembled and ready to
use. Enjoy!
FINISH: MYSTIC BLACK
5.5” SQ.
6.5”
4.5” SQ.
Fixture can
only be
mounted in
the direction
indicated
6.25”
11.25”
Figure 6
Exterior
Grade
Caulk
Backplate
Socket
Bulb (not
Supplied)
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
Thank you for purchasing product.
2of2
Loading...