PACKAGE CONTENTS
INSTRUCTION SHEET
GENERAL IS SHEETS FOR OUTDOOR WALL LANTERN
Part
A
B
C
D
E
F
G
Description
Crossbar
Green Ground Screw
Mounting Screw
Lock Washer
Hex Nut
Mounting Ball
Fixture Body
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
A
B
C
D
E
F
G
!
WARNINGS AND CAUTIONS
WARNING:
● Befo re beginnin g the installation, turn off electricity at the cir cuit br eaker box or the ma in fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are pr ovide d for your safety. It is very important that they are read comp letel y before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fi xture from the pow er source before replacing th e bulb( s), makin g sure t he b ulb(s ) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
● Befo re beginnin g installation of product, ma ke sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estima ted Asse mbly Time: 15 30 minutes
● Tools Required for Assembly (n ot included): Flathead screw drive r Phil lip s screwdriver, pliers, electrical
tape, wire cutters, safety glasses & proper Bulb(s).
● Help ful Tool s (n ot included) : Wire Strippers.
CAUTION
● The Step 2 is only for lanya rd purp ose. Lanyard might be required a ccording to the we ight of the fixture.
,
1 OF 3
INSTALLATION INSTRUCTIONS
GENERAL IS SHEETS FOR OUTDOOR WALL LANTERN
STEP 1:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure the
.
position of the Mounting Screws by tightening the Hex Nuts
against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
STEP 2 (For Lanyard purpose only):
a Locate the Backplate onto the Crossbar and slip the Button
.
Stop on the end of Lanyard into the Slot on the Crossbar as
shown.
Mounting Screw
Crossbar
Hex Nut
Lock Washer
Outlet Box
Outlet Box Screw
Button Stop
Lanyard
Slot
STEP 3:
* ( )
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
. ( )
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
( ).
( )
carefully stuff all of the connected wires into the Outlet
.
Box
STEP 4:
a. Place the Backplate over the Mounting Screws and secure
with Mounting Balls. Hand tighten until snug.
Crossbar
Backplate
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
Mounting
Screw
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Mounting Ball
Outlet Box
Backplate
STEP 5:
a Install correct bulb(s) referring to fixture markings and or labels for maximum wattage. / .
2 OF 3
INSTALLATION INSTRUCTIONS
STEP 6 :
a Refer to following information for caulking instructions. :
GENERAL IS SHEETS FOR OUTDOOR WALL LANTERN
For assemble the MOUNTING BALLS please note that
,
you are required to apply a small amount of Silicone
sealer to the threaded side of the MOUNTING BALLS
EXTERIOR GRADE
and then install them onto the MOUNTING SCREWS
CAULK
MOUNTING BALL
.
With the OUTDOOR FIXTURE properly installed in accordance with supplied Assembly/installation
instructions, proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking.
Using EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were
the FIXTURE BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of
backplate and down other side. to ensure proper
DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE
moisture drainage.
EXTERIOR GRADE
CAULK
OUTDOOR
FIXTURE BACKPLATE
EXTERIOR WALL SURFACE
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
3 OF 3
Loading...