Page 1
Warnings: You must read this before you proceed.
Dining Chair
1 OF 7
Page 2
Part NO. Picture Description Qty
A Chair Back 1 PC
B Chair Seat 1 PC
C Front Leg 2 PCS
Label Picture Description Qty
a Bolt M8X100
4 PCS
b Bolt M8X65
6 PCS
d Flat Washer Ring
10 PCS
e Spring Washer Ring
10 PCS
f Allen Key
1 PC
2 OF 7
Page 3
Pack A
M8X65mm bolts - 6pcs
&M8X100mm bolts- 4pcs
matching with 10pcs of
Flat Washer Ring and
matching with 10pcs
Spring washer
Unpack and
place all
parts for
clear
visibility.
Before Beginning Assembly:
3 OF 7
Page 4
Step 1
Chair Back Chair Seat
Step 2
Place the chair back(A) on a soft surface to avoid any scratches
on the products.
Take out the 2 wooden legs and the package of hardware
accessories.
Put the chair back( A) onto a flat table or panel.
Align the holes on chair back(A) to the holes on chair seat frame.
Use your left hand to push the seat frame floorwards, depicted by
Arrow 1.
This action helps to ensure the chair seat(B) is pressed towards to
the chair back(A) with no gap between these.
Then, lock the middle hole(use Bolt b) and the corner holes(use Bolt
a).
The hardware for these are : use 4 Bolts (a)+ 2 Bolts (b) +6 Flat
Washers (d) + 6 Spring Washers (e) with the Allen key(f).
At this point of assembly, DO NOT overfasten the connections.
4 OF 7
Page 5
Step 3
Next, place the chair onto the side of a table as seen in Picture 1.
You will now have the chair bottom and all 4-legs facing skywards.
Insert each front leg completely vertically into each seat frame
corner.
PRESS FIRMLY DOWN with your hand until there is no gap.
WARNING!! DO NOT POSITION THE FRONT LEG AS SHOWN
IN PICTURE 2 .
THIS PICTURE SHOWS THE CHAIR BACK STAYS AGAINST
THE GROUND and THE FRONT LEGS HORIZONTAL IN
MIDAIR.
Now tighten the bottom bolt first, then the bolt on the top by using
4 Bolts (b) and 4 Flat Washers (d) and 4 Spring Washers (e).
DO NOT tighten the top bolt first.
WARNING!! DO NOT OVER TIGHTEN. OVER TIGHTENING
COULD LEAD TO DAMAGE OF THE PRODUCT.
TIGHTEN ONLY UNTIL SECURE AND STABLE.
5 OF 7
Page 6
Step 4
Step 5
Finally, seal the Seat Base Cover back on to the underside of the
chair seat . Turn it the right side up.The chair is ready for use.
Place the chair on a LEVEL SURFACE to see if it wobbles.
If it wobbles, lift the chair to some 30cm to 50cm height from the
ground.
Keep your feet and toes well away from the drop zone.
Drop the chair freely and vertically with the four legs, hitting the
ground, at the same time.
This Drop Test will help to ensure that all the bolts and gaps to all
reach full alignment status.
Test again for evenness on a LEVEL SURFACE.
If no wobbles found, proceed to tighten all the bolts.
CAUTION : When tightening these bolts, tighten sequentially.
DO NOT tighten any screw fully and then towards the next one.
This would cause the frame to warp.
If there is still wobbles, loosen the bolts and execute this same
drop tests.
WARNING!! IF CHAIR IS NOT STABLE , IT COULD LEAD TO
DAMAGING THE PRODUCT.
If wobble
Test again
30~50cm
6 OF 7
Page 7
7 OF 7
Loading...