ASSEMBLY AND INSTALLATION
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Cross Bar(A)
Swivel (I)
Wire Connector (F)
House Grounding Wire
Outlet Box
Mounting Screw (B)
Hex Nut (J)
Mounting Screw (B)
Cross Bar(A)
Washer (K)
Lock Nut(D)
Headless Screw (C)
Headless Screw (C)
Anchor (L)
Back Plate
Ball Nut (G)
Lock Nut
Threaded Pipe (M)
Bulb Type A Max.60W
(not included)
Green Grounding
(D)
Screw (E)
Inner Shade
Socket Ring
Outer Shade
Socket
Wire Connector (F)
Pipe Strap (N)
Holder
Ball Nut (G)
Dry Wall Screw (O)
Strain Relief (H)
Bushing (P)
Fixture Grounding Wire
Green Grounding Screw (E)
Fixture Wire
This FIXTURE can be mounted in two ways.
Option 1: (Hard Wire Installation)
Assembly Instructions:
Turn off the power at fuse or circuit box.
Page 1
Rocker Arm
1. Thread two headless screws through the cross bar, then secure them with four lock nuts (two on each side of the
cross bar). Adjust the length of the headless screws if necessary.
Note: Make sure that the headless screws are lined up horizontally to make the fixture level.
2. Attach the cross bar to the outlet box by using two mounting screws.
3. Pull out the source wires from the outlet box. Make wire connections using wire connectors as follows:
---Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source.
---Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source.
---Attach the fixture grounding wire (usually bare wire) to the cross bar with the green grounding screw, then connect
it to the house grounding wire with a wire connector. If your outlet box does not have a house grounding wire, then
wrap the fixture grounding wire around the green grounding screw.
Carefully tuck the wires back into the outlet box.
4. Attach the back plate to the cross bar by inserting the headless screws, then secure it with the ball nuts.
5. Attach the outer shade onto the holder and secure it with the socket ring. Place inner shade into outer shade.
6. Install bulb (not included). See relamping label at socket area or packaging for maximum allowed wattage.
Turn on the power at fuse or circuit box.
Fig.1
Option 2: (Plug-in Installation)
Assembly Instructions:
Turn off the power at fuse or circuit
box.
1. Remove and discard the stopper from the
back plate.
2. Thread headless screws through the cross
bar, then secure them with four lock nuts
(two on each side of the cross bar). Adjust
the length of the headless screws if
necessary.
Note: Make sure that the headless screws
are lined up horizontally to make the fixture
level.
3. Unscrew and discard the green grounding
screw from the cross bar.
Back Plate
Wire Connector (F)
Headless
Screw (C)
Cross Bar (A)
Anchor (L)
Bulb Type A Max.60W
(not included)
Inner Shade
Socket Ring
Outer Shade
Ball Nut (G)
Socket
Holder
4. Place the cross bar to a proper position.
a) If the wall material is wood:
Attach the cross bar to the wall, then
secure it with the dry wall screws
b) If the wall material is cement: Mark the
holes where you want to place the
cross bar on the wall. Drill the holes
and insert the anchors into the holes,
then attach the cross bar to the wall,
secure the dry wall screws into the
anchors.
5. Thread plug cord through the pipes,
swivel, threaded pipe, the bottom hole of
the back plate, washer, and hex nut in turn
as shown in Fig.1, then connect the pipes.
6. Secure the assemble pipes to the back
plate by using the washer and hex nut.
Dry Wall
Screw(O)
Lock Nut
Strain Relief (H)
Anchor (L)
(D)
Stopper
Pipe
Plug Cord
Page 2
Hex Nut (J)
Washer (K)
Threaded Pipe (M)
Set Screw
Swivel (I)
Bushing(P)
Pipe Strap (N)
Dry Wall Screw (O)
Plug
Cover
7. Thread the plug cord through two holes of the
strain relief. Pull the plug cord down until the
strain relief touches the back plate.
Note: Adjust the strain relief can decrease or
increase the length of the exposed plug cord.
8. Cut any excess plug cord leaving 10 inches
from the back plate. Slit the plug cord apart in
5 inches. Peel off insulation of the two wires
in 5/8 inch. (See Fig.2)
Fig.2
Plug Cord
Back Plate
5"
5/8"
9. Pull out the source wires from the back plate.
Make wire connections using wire connectors
as follows:
---The black wire from the back plate to the smooth wire (marked) from the plug cord.
---The white wire from the back plate to the ridged wire (unmarked) from the plug cord.
Carefully put the wires back into the back plate.
10. Attach the back plate to the cross bar by inserting the headless screws, then secure it with the ball nuts.
11. Attach the pipe strap to the connected pipe at the bottom, then secure it to the wall by using dry wall screws.
a) If the wall material is wood:
Attach the pipe strap to the wall, thread the dry wall screws through the holes on pipe strap, then secure them to the
wall.
b) If the wall material is cement:
Mark the holes where you want to place the pipe strap on the wall. Drill the holes and insert the anchors into the
holes, then attach the pipe strap to the wall, thread the dry wall screws through holes on pipe strap, and then secure
them into the anchors.
10"
12. Attach the outer shade onto the holder and secure it with the socket ring. Place inner shade into outer shade.
13. Install bulb (not included). See relamping label at socket area or packaging for maximum allowed wattage.
14. Insert the plug into the wall receptacle.
Note:Remove the cover from the plug when the plug is used for the first time.
Turn on the power at fuse or circuit box.
Function and Operation
When power is first applied, the light will turn to high level brightness.
Note: Detection zone is within 4.5 inch distance from the sensor.
1x
2x
TURNING LIGHTS ON/OFF
Wave hand under sensor once to
turn light on and off.
DIMMING LIGHTS
Hold hand under sensor to adjust
brightness.
Page 3
ACTIVATING SLEEP FEATURE
Wave hand under sensor twice. Light
will flash, then gradually dim-to-off in
5 minutes.
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Cross Bar(A)
Ball Nut (G)
Threaded Pipe (M)
Mounting Screw (B)
Strain Relief (H)
Pipe Strap (N)
Headless Screw (C)
Swivel (I)
Dry Wall Screw (O)
Lock Nut
Hex Nut (J)
Green Grounding
(D)
Screw (E)
Bushing (P)
Washer (K)
Wire Connector (F)
Assembly Kit
(1 SET)
Anchor (L)
5-YEAR LIMITED WARRANTY:
All products are warranted to be free of defects in material and workmanship for five (5) years from date of
purchase. This warranty is limited to the correction of any such defect, or the replacement of any such defective
item(s), provided that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item (s)
is / are returned with proof of purchase date; and (c) it is found upon inspection by us that the item (s) is / are defective
as noted above. This warranty dose not cover labor costs, consequential damages, nor dose it apply to any item(s) that
have been improperly installed, overloaded, altered, or otherwise abused by the customer, its agent(s) or emplyee(s).
Finishes are specially excluded from the terms of this warranty since they are subject to environmental maintenance
deemed beyond our control. Other than the described obligation, we assume no further liability with respect to the sale
or use of our products.We make no warranty, express or implied, and disclaim any warranty of merchantability or fitness
for a particular purpose.
B
C
A: 21-3/4"
B: 11-1/2"
C: 10"
A
Page 4
Loading...