Charlotte Pipe PVC 4112, PVC 4200, PVC 4300, PVC 4400, PVC 4600 User Manual

SUBMITTAL FOR CHARLOTTE PIPE®

PVC CELLULAR (FOAM CORE) PIPE AND PVC DWV FITTING SYSTEM

Date: ________________

Job Name: ______________________________ Location: _______________________________

Engineer: _______________________________ Contractor: ______________________________

Scope:

This specication covers PVC cellular (foam core) pipe and PVC DWV ttings used in sanitary drain, waste and vent
(DWV), sewer, and storm drainage applications. This system is intended for use in non-pressure applications where
the operating temperature will not exceed 140° F.

Specication:

Pipe shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a cell class of 11432 as
identied in ASTM D 4396. Fittings shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds
with a cell class of 12454 as identied in ASTM D 1784.

PVC cellular core pipe shall be Iron Pipe Size (IPS) conforming to ASTM F 891. Injection molded PVC DWV ttings
shall conform to ASTM D 2665. Farbricated PVC DWV ttings shall conform to ASTM F 1866. All systems shall utilize
a separate waste and vent system. All pipe and ttings shall be manufactured in the United States. Pipe and ttings
shall conform to NSF International Standard 14.

Installation:

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall
conform to all applicable plumbing, re, and building code requirements. Buried pipe shall be installed in accordance
with ASTM D 2321 and ASTM F 1668. Solvent cement joints shall be made in a two-step process with primer
conforming to ASTM F 656 and solvent cement conforming to ASTM D 2564. The system shall be protected from
chemical agents, re-stopping materials, thread sealant, plasticized-vinyl products or other aggressive chemical
agents not compatible with PVC compounds. The system shall be hydrostatically tested after installation.
WARNING! Never test with or transport/store compressed air or gas in PVC pipe or ttings. Doing so can result in
explosive failures and cause severe injury or death.

Referenced Standards:

ASTM D 4396: Compounds for Cellular Core
ASTM F 891: Co-extruded PVC Pipe with Cellular Core
ASTM D 2665: PVC Drain, Waste and Vent Fittings
ASTM D 2564: Solvent Cements for PVC Pipe and Fittings
ASTM D 2321: Underground Installation of Thermoplastic

Pipe (non-pressure applications)

ASTM F 1668: Procedures for Buried Plastic Pipe
ASTM F 1866: Fabricated PVC DWV Fittings
NSF Standard 14: Plastic Piping Components and
Related Materials

Coupling

Cleanout Tee

w/Plug

Not all tting patterns shown

Quarter Bend

Combination Wye

& Eighth Bend

Eighth Bend

Double

Sanitary Tee

Closet FlangeP-Trap

PVC Foam Core Pipe

PVC Schedule 40 DWV Pipe
(For Non-Pressure Applications)

PVC SCHEDULE 40 FOAM CORE (WHITE) PLAIN END ASTM F 891

MIN. WT. PER
PART NO. NOM. SIZE UPC # QTY. PER AVG. OD WALL 100 FT.
611942- SKID (IN.) (IN.) (LBS.)

PVC 4112 11⁄2” x 10’ 04178 1650’ 1.900 0.145 32.3

1

PVC 4112 1

PVC 4200 2” x 10’ 04174 1110’ 2.375 0.154 43.9

PVC 4200 2” x 20’ 04173 2220’ 2.375 0.154 43.9

PVC 4300 3” x 10’ 03934 1130’ 3.500 0.216 89.7

PVC 4300 3” x 20’ 03935 1000’ 3.500 0.216 89.7

PVC 4400 4” x 10’ 03936 670’ 4.500 0.237 123.8

PVC 4400 4” x 20’ 03937 1340’ 4.500 0.237 123.8

PVC 4600 6” x 10’ 03938 330’ 6.625 0.280 235.0

PVC 4600 6” x 20’ 03939 660’ 6.625 0.280 235.0

PVC 4800 8” x 20’ 03941 360’ 8.625 0.322 371.0

PVC 4910 10” x 20’ 03942 220’ 10.750 0.365 566.3

PVC 4912 12” x 20’ 03943 120’ 12.750 0.406 700.0

⁄2” x 20’ 04177 3300’ 1.900 0.145 32.3

Charlotte Pipe and Foundry Company • P.O. Box 35430 Charlotte, NC 28235 • [phone] • www.charlottepipe.com

Charlotte Pipe and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company.

FO-SUB-PVC-FC (12-19-19)