Charlotte Pipe ABS 3112, ABS 3200, ABS 3300, ABS 3400, ABS 3600 User Manual

SUBMITTAL FOR CHARLOTTE PIPE®

ABS CELLULAR (FOAM CORE) PIPE AND ABS DWV FITTING SYSTEM

Date: ________________

Job Name: ______________________________ Location: _______________________________

Engineer: _______________________________ Contractor: ______________________________

Scope:

This specication covers ABS cellular core (foam core) pipe and ABS DWV ttings used in sanitary drain, waste and
vent (DWV), sewer, and storm drainage applications. This system is intended for use in non-pressure applications
where the operating temperature will not exceed 140° F.

Specication:

Pipe shall be manufactured from virgin rigid ABS (acrylonitrile-butadiene-styrene) compounds with a cell class of
42222 as identied in ASTM D 3965. Fittings shall be manufactured from virgin rigid ABS compounds with a cell class
of 32222 as identied in ASTM D 3965.

ABS cellular core pipe shall be Iron Pipe Size (IPS) conforming to ASTM F 628. Injection molded ABS DWV ttings
shall conform to ASTM D 2661. All systems shall utilize a separate waste and vent system. All pipe and ttings shall
be manufactured in the United States. Pipe and ttings shall conform to NSF International Standard 14.

Installation:

Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall
conform to all applicable plumbing, re, and building code requirements. Buried pipe shall be installed in accordance
with ASTM D 2321 and ASTM F 1668. Solvent cement joints shall be made with a solvent cement conforming
to ASTM D 2235. The system shall be protected from chemical agents, re-stopping materials, thread sealant,
plasticized-vinyl products or other aggressive chemical agents not compatible with ABS compounds. The system shall
be hydrostatically tested after installation. WARNING! Never test with or transport/store compressed air or gas in ABS
pipe or ttings. Doing so can result in explosive failures and cause severe injury or death.

Referenced Standards:

ASTM D 3965: Rigid ABS Compounds
ASTM F 628: Co-extruded ABS Pipe with Cellular Core
ASTM D 2661: ABS Drain, Waste and Vent Fittings
ASTM D 2235: Solvent Cements for ABS Pipe and Fittings
ASTM D 2321: Underground Installation of Thermoplastic

Pipe (non-pressure applications)

ASTM F 1668: Procedures for Buried Plastic Pipe
NSF Standard 14: Plastic Piping Components and
Related Materials

ABS Foam Core Pipe

ABS Schedule 40 DWV Pipe
(For Non-Pressure Applications)

ABS SCHEDULE 40 FOAM CORE (BLACK) PLAIN END ASTM F 628

MIN. WT. PER
PART NO. NOM. SIZE UPC # QTY. PER AVG. OD WALL 100 F T.
611942- SKID (IN.) (IN.) (LBS.)

Coupling

Cleanout Tee

w/Plug

Not all tting patterns shown

Charlotte Pipe and Foundry Company • P.O. Box 35430 Charlotte, NC 28235 • [phone] • www.charlottepipe.com

Charlotte Pipe and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company.

FO-SUB-ABS (3-11-19)

Quarter Bend

Combination Wye

& Eighth Bend

Eighth Bend

Double

Sanitary Tee

Closet FlangeP-Trap

ABS 3112 11⁄2” x 10’ 03132 2590’ 1.900 0.145 27.1

ABS 3112 11⁄2” x 20’ 03133 5180’ 1.900 0.145 27.1

ABS 3200 2” x 10’ 03134 1670’ 2.375 0.154 37.7

ABS 3200 2” x 20’ 03135 3340’ 2.375 0.154 37.7

ABS 3300 3” x 10’ 03136 750’ 3.500 0.216 74.5

ABS 3300 3” x 20’ 03137 1500’ 3.500 0.216 74.5

ABS 3400 4” x 10’ 03138 480’ 4.500 0.237 107.1

ABS 3400 4” x 20’ 03139 960’ 4.500 0.237 107.1

ABS 3600 6” x 10’ 03140 200’ 6.625 0.280 187.8

ABS 3600 6” x 20’ 03141 400’ 6.625 0.280 187.8