Charlotte Pipe 2112, 2116 User Manual
SUBMITTAL FOR CHARLOTTE PIPE®
PVC SCHEDULE 40 PRESSURE PIPE AND FITTING SYSTEM
Date: ________________
Job Name: ______________________________ Location: _______________________________
Engineer: _______________________________ Contractor: ______________________________
Scope:
This specication covers PVC Schedule 40 pipe and ttings for pressure applications. This system is intended for
pressure applications where the operating temperature will not exceed 140° F.
Specication:
Pipe and ttings shall be manufactured from virgin rigid PVC (polyvinyl chloride) vinyl compounds with a cell class of
12454 as identied in ASTM D 1784.
PVC Schedule 40 pipe shall be Iron Pipe Size (IPS) conforming to ASTM D 1785. Injection molded PVC Schedule 40
ttings shall conform to ASTM D 2466. Pipe and ttings shall be manufactured as a system and be the product of one
manufacturer. All pipe and ttings shall be manufactured in the United States. Pipe and ttings shall conform to NSF
International Standard 61 and the health-effects portion of NSF Standard 14.
Installation:
Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall
conform to all applicable plumbing, re, and building code requirements. Buried pipe shall be installed in accordance
with ASTM F 1668. Solvent cement joints shall be made in a two-step process with primer conforming to ASTM F 656
and solvent cement conforming to ASTM D 2564. The system shall be protected from chemical agents, re-stopping
materials, thread sealant, plasticized-vinyl products or other aggressive chemical agents not compatible with PVC
compounds. The system shall be hydrostatically tested after installation. WARNING! Never test with or transport/store
compressed air or gas in PVC pipe or ttings. Doing so can result in explosive failures and cause severe injury or
death.
Referenced Standards:
ASTM D 1784: Rigid Vinyl Compounds
ASTM D 1785: PVC Plastic Pipe, Schedule 40
ASTM D 2466: PVC Plastic Fittings, Schedule 40
ASTM D 2564: Solvent Cements for PVC
Pipe and Fittings
ASTM F 1668: Procedures for Buried Plastic Pipe
NSF Standard 14: Plastic Piping Components & Related Materials
NSF Standard 61: Drinking Water System Components –
Health Effects
E
D
I
A
N
M
.
S
A
.
.
U
Quarter Bend
Male Adapter
Plug
Not all tting
patterns shown
Charlotte Pipe and Foundry Company • P.O. Box 35430 Charlotte, NC 28235 • (800) 438-6091 • www.charlottepipe.com
Charlotte Pipe and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company.
FO-SUB-PVC-40 (5-30-19)
Eighth Bend
Bushing
Female Adapter
Tee Coupling
Schedule 40
Tapered Socket Dimensions
PVC SCHEDULE 40 - ASTM D 2466
Cross
Street Quarter
Bend
Cap
PIPE REFERENCE GUIDE
Sizes Available
1
3
Product
PVC Schedule 40
1
⁄
2
⁄
4
11⁄
• • • • • • • • • • • • • • • •
Schedule 80 and Schedule 40 Socket Diameter Schedule 80 Schedule 40
Nominal Entrance Bottom Tolerance S ocket Length Socket Length
Size A B C (Minimum) C (Minimum)
1⁄2 0.848 0.836 ±0.004 0.875 0.688
3
⁄4 1.058 1.046 ±0.004 1.000 0.719
1 1.325 1.310 ±0.005 1.125 0.875
1
⁄4 1.670 1.655 ±0.005 1.250 0.938
1
1
⁄2 1.912 1.894 ±0.006 1.375 1.094
1
2 2.387 2.369 ±0.006 1.500 1.156
1
⁄2 2.889 2.868 ±0.007 1.750 1.750
2
3 3.516 3.492 ±0.008 1.875 1.875
4 4.518 4.491 ±0.009 2.250 2.000
6 6.647 6.614 ±0.011 3.000 3.000
8 8.655 8.610 ±0.015 4.000 4.000
10 10.780 10.735 ±0.015 5.000 5.000
12 12.780 12.735 ±0.015 6.000 6.000
2
4
11⁄
2
3 4 5 6 8 10 12 14
21⁄
2
16
Schedule 40 Fittings
Reducer Bushing
MPT x FPT
PVC PART NO. 2112
Universal Approx.
Size Part Number L T N Wt. (Lbs)
3⁄
4
x 1⁄2 439-101 1 3⁄
1 x 1⁄2 439-130 11⁄4
1 x 3⁄4 439-131 11⁄4
11⁄
4
x 3⁄4 439-167 15⁄16
11⁄
4
x 1 439-168 15⁄16 1
11⁄
2
x 3⁄4 439-210 13⁄8
11⁄
2
x 1 439-211 13⁄8 1
11⁄
2
x 11⁄4 439-212 13⁄8 1
2 x 11⁄2 439-251 17⁄16 1
4
3
⁄
4
3
⁄
4
3
⁄
4
23
⁄
32
1
⁄4 0.022
1
⁄2 0.059
1
⁄2 0.043
9
⁄16 0.092
5
⁄16 0.063
21
⁄32 0.128
11
⁄32 0.110
3
⁄8 0.068
7
⁄16 0.143
Cap
S
PVC PART NO. 2116
Universal Approx.
Size Part Number L S Wt. (Lbs)
1⁄2 447-005 11⁄8
3⁄4 447-007 13⁄32
3
⁄4 0.024
3
⁄4 0.035
1 447-010 15⁄8 15⁄32 0.060
11⁄4 447-012 113⁄16 11⁄4 0.094
11⁄2 447-015 13⁄4 11⁄8 0.116
2 447-020 25⁄32 113⁄32 0.184
21⁄2 447-025 217⁄32 113⁄16 0.368
3 447-030 215⁄16 129⁄32 0.463
4 447-040 31⁄8 21⁄32 0.720
6 447-060 41⁄2 31⁄32 2.349
8 447-080 63⁄16 4 4.074
44
Loading...