Chargery Power S1500 Instruction Manual

©

2013 Chargery Power Co., Ltd. 06/18/2013 V1.1

Add: Room 6-303, Langqinyu, Chuangye Road NanShan 518054 ShenZhen, China,

Tel: [phone], Fax: [phone], Email: [e-mail]

S1500

PFC programmable Power supply
High efficiency wide input voltage

90V~265VAC Input

10V~25V DC Output

60Amps 1500W max.

T

hanks for your purchasing the intelligent and powerful power supply.

R

ead the ENTIRE instruction manual to become familiar with the features/functions of the device

before operating.

F

eel free to send an email to [e-mail] or call at 86 755 2643 6165 should you have

any questions and suggestions.

Jason Wang

S1500

High efficiency wide input voltage

PFC programmable Power supply

90V~265VAC input

10V~25VDC output

60Amps 1500W max.

www.chargery.com

page

2

total

8

Features

S

1500 is a high efficiency wide input voltage PFC power supply, the device can output 1500W at

AC90V~265V in a smaller size. Many creative technology help to realize up to 94% of efficiency, and the

internal temperature is still under 80℃. The following are some new features:

 Intelligent control output voltage and current by microprocessor, 100% calibration before

delivery

 ±1% voltage and current accuracy
 Active PFC: smaller AC input current less interference, and Conform to European Commission

Regulation no 278/2009 and Energy Star Version 2.0

 AC 90-265V worldwide operation: need not any alternative switcher, worldwide safe operation.
 Low power consumption (less than 1W) at idle mode and standby mode
 Up to 94% of convert efficiency.
 Programmable output voltage from 10 to 25V
 Programmable output current from 5 to 60A
 1.8” TFT color LCD display output Voltage, current, power and internal temperature on time.
 Over current, over voltage, over load, over temperature, and short circuit protection
 Short-circuit protection on output, safer and more reliable.
 2 Intelligent cooling fans turned on upon the temperature automatically
 4 outputs can do more chargers simultaneously, 3 pairs 4.0mm gold connector up to 20A each

output, one 4.5mm gold connector (XT-90) up to 60A

 ZVS/ZCS and Synchronous Rectification assure the highest efficiency.
 High power density: 652W/Kg
 Start at no load or full load
 Approved by CE
 24 months warranty

Application

 Home application
 10-25V DC charger, balance charger for RC mode

S1500

High efficiency wide input voltage

PFC programmable Power supply

90V~265VAC input

10V~25VDC output

60Amps 1500W max.

www.chargery.com

page

3

total

8

 E-bike, E-scooter battery charger.

Operation

1. Connect S1500 to AC 110 / 220V outlet by the special heavy power cable, if use other brand cable,

please note the wire AWG must be AWG14 at least.

2. 2 seconds later, default output voltage (12V) and maximal output current can be displayed, actual

power and internal temperature is also displayed, but S1500 is at idle mode(power off) to save

power consumption, as the following picture 1. Confirm the voltage and current is suitable for your

charger and other load, then press START/ENTER button turn on S1500, the LCD will display actual

output voltage, current, output power and internal temperature as the following picture 2.

If the voltage is NOT suitable for your charger or other load, press INC or DEC button setup the

voltage. It is easy to adjust as same as a potential meter and need not confirm the change, because

the voltage will be updated with your operation. Finish the voltage setup, the device can remember

the new value till next change.

You can also change the voltage at any time whether power on

or power off status.

If need change the maximal current or other items, please

operate according to the following steps.

3. Press STOP/SET button for 2 seconds can enter into Program

Setup menu, The LCD displays the following information in

sequence and you can change the value. When you want to alter a

parameter value, press the

Start/Enter button to the value blink then change the value with the DEC

or INC buttons. The new value will be confirmed and saved by pressing the Start/Enter button again.

Picture 3

Program setup

Power OFF / Power ON

Actual power

Setup voltage/Actual voltage

I

nternal temperature

Setup current/Actual current

P

icture 1

:

Idle mode

Picture 2: work mode