Chargery Power 550B Operating Instructions Manual
Operating Instructions
1-5S LiPo battery Smart Balance Charger
Chargery Power Co., Ltd.
Head Office
Add: Room 20B, Haihui Building, NanShan, ShenZhen, China
Zip code: 518054
Tel: +86 755 26436165
Fax: +86 755 26412865
Email: Jasonwang3a@163.com
Web: www.chargery.com
LiPo Smart Balance Charger CY- 550B.
www.chargery.com
page 2 total 11
Welcome to use CHARGERY 550B-- A LiPo Smart balance charger is designed specially for 1 to 5
LiPo cells in series NOT FOR LEAD ACID and NIMH/NICD. Please read the instructions before using
the charger.
Special Features
Built-in balancer for LiPo cells
550B has an individual cell balancer inside, so it can charge and balance the battery pack
simultaneously.
Only for LiPo not lead acid battery and NIMH/NICd battery pack
It is super easy to operate the 550B. You need not choose and confirm the battery type; the
battery chemistry is no opportunity to confuse you. What you do is to connect the charger to
the battery pack and then to connect the DC power to the charger.
High power and high performance circuit
CY-550B employs the circuit that has maximum output power of 50W. As a result it can charge
5 series of lipo batteries with maximal current of 2. 5A.
Dual confirmation for battery count in series
Besides set up manually the battery count (the result is “S”), the C550B will identify the count
automatically (the result is “R”), and adjust the charging voltage and current automatically
through comparing the “ S ” with “ R ”.
Perfect safety design
Charging time limit
The charging time can be restrained; you can set it upon the battery status to prevent from
any possible defect.
Battery temperature limit
The battery temperature will rise by its internal chemical reaction. If you set the limit of
temperature the charging process will be stopped forcibly when the temperature reach the
limit.
Capacity charged limit
The capacity charged always calculated by multiple of the charge current and time. If the
capacity charged reached the limit you set the charging will be terminated automatically.
Input power monitor
To protect the car battery using as input power from being damaged the input voltage always
monitored. If it drops the lower limit the charging process will be ended automatically.
At the same time, when you use the AC adaptor or transformer as input power, if the input
voltage is more than the limit the charging process will be terminated to protect the CY-550B
from being damaged.
High back-light LCD screen
The clear back- light LCD shows pack voltage, charge current, charge time, capacity charged.
LiPo Smart Balance Charger CY- 550B.
www.chargery.com
page 3 total 11
Light and fashion AL alloy case
High-quality aluminum case is light and durable and very efficient to cool out the internal
heat.
Protection function
Reverse polarity and short circuit protection( input and output)
Over charge and Over current protection
Detect the over-discharged battery and pre-charge the battery at a small current to
resume the battery capacity
For the battery voltage is less than 2V/each cell, the CY-550B will refuse to charge to
prevent from happen safety accident.
Program flow chart
Temp shut off
ON 80℃
User Config
Program
Charging time
ON 010min
Capacity charged
ON 3000mAh
Push Button ON
Buzzer ON
Low Input voltage
YES 10.7V
Back-light
78%
Start/ Enter
DEC INC
DEC INC
DEC INC
Welcome to
Chargery Power
Start/enter
DEC INC
DEC
DEC INC
LiPo Bat Charge
3.0A 11.1V(3S)
Li S:3SER R:3SER
Confirm (enter)
Li3S 1.2A 12.13V
CHG 011:10 00345
Start/Enter
Start/Enter
>3 seconds
BL S:3Ser R:3Ser
Confirm (enter)
BL3S 1.2A 12.13V
CHG 011:10 00345
Start/Enter
Stop
LiPo Smart Balance Charger CY- 550B.
www.chargery.com
page 4 total 11
Initial parameter set up
CY-550B will be operated with the default value of the essential user settings when it is connected
to a 12V battery or a 12V adapter for the first time. The LCD displays the following information in
sequence and the user can change the value of parameter on each step. When you are willing to
alter the parameter value in the program, press start/enter button to make it blink then change
the value with DEC or INC button. The value will be stored by pressing start/enter button once.
.
Temp shut off
ON 80℃
Charging time
ON 010min
Capacity charged
ON 3000mAh
Push Button ON
Buzzer ON
Low Input Power
on 10.7V
Back-light
78%
This is star screen.
An optional feature using temperature probe contacts the surface of battery. The feature can
be on or off. If it is on, set the maximal temperature at which the charger allows battery to
reach during charge. Once the battery temperature reaches the limit while charge, the
charging will be ended to protect the battery
When you start a charge process, the integral safety timer automatically starts running at the
same time. This is programmed to prevent overcharge the battery if it proves to be faulty or
if the termination circuit can not detect the battery full charged. The value should be
generous enough to allow a full charge of the battery
The program sets the maximal charge capacity that will be supplied to the battery during
charge. If the termination circuit can not detect the battery full charged, this feature will
automatically stop charging at the set capacity value.
The beep sounds at every time pressing the buttons to confirm your action. The beep or
melody sounded at various times during operation to alert different mode changes. These
audible sounds can be on or off.
The program monitors the voltage of battery used as input power. If the voltage drops below
the value you set, the charging process will be terminated forcibly to protect the battery.
You can adjust the brightness of LCD screen at the charger.
User Config
Program
Start/ Enter
DEC INC DEC INC
DEC INC DEC INC
DEC INC DEC INC
DEC INC
DEC INC
DEC INC
Loading...