Charder MS 4600, MS 4610 User Manual

35

Manufacturer’s Declaration of Conformity

This product has been manufactured in accordance with
the harmonized European standards, following the
provisions of the below stated directives:

93/42/EEC as amended by

2007/47/EC
Medical Device Directive

2014/31/EU
Non-

automatic Weighing Instruments

Directive

Please see separate document showing on sticker of device for
above CE marking.

Authorized EU Representative:

Manufactured by:

Charder Electronic Co., Ltd.

No.103, Guozhong Rd., Dali Dist.,
Taichung City 412,Taiwan (R.O.C.)

FDA no.: D051882

IN-1012 [7025L] 04/2016

- 0 -

MS 4600/4610

USER MANUAL

Please keep the instruction manual at hand all the time for future reference.

- 1 -

TABLE OF CONTENTS

PREFACE................................................................................................. 2

GENERAL INFORMATION .................................................................... 2

SAFETY INSTRUCTION.........................................................................2

ENVIRONMENTAL................................................................................. 3

CLEANING.............................................................................................. 3

MAINTENANCE ..................................................................................... 3

WEIGHING OPERATION........................................................................ 4

WARRANTY-LIABILITY........................................................................ 4

DISPOSING OF THE SCALE.................................................................. 5

EXPLANATION OF THE GRAPHIC SYMBOLS.................................... 6

EMC guidance and manufacturer's declaration.......................................... 8

SPECIFICATION.................................................................................... 13

MEDICAL SCALE MODELS APPROVAL LIST................................... 14

PANEL.................................................................................................... 15

KEY FUNCTION................................................................................... 16

LCD DISPLAY SYMBOLS.................................................................... 18

USING SCALE....................................................................................... 19

USING HOLD FUNCTION.................................................................... 19

USING TARE FUNCTION..................................................................... 21

MS 4610- STORING AND RE-CALLING PRE-TARE WEIGHT.......... 22

USING BMI FEATURE.......................................................................... 25

MS4610 & 4600: SET-UP....................................................................... 27

PRINT FUNCTION................................................................................ 28

INSTRUCTION FOR CHARGING AND CONNECTING..................... 31

INSTRUCTION FOR REPLACING BATTERIES.................................. 32

ERROR MESSAGE................................................................................ 33

34

NOTE

33

ERROR MESSAGE

- 2 -

PREFACE

Thank you for choosing CHARDER MEDICAL product. All features
of this product were designed to state of the art and are optimized
for simple and straightforward use. If you have any queries or
experience any problems not addressed in the operating
instructions, please contact your CHARDER MEDICAL service
partner, or visit us on the Internet at

www.chardermedical.com

GENERAL INFORMATION

We strongly recommend you use the scales on flat and hard surface.
Any soft surface, like carpet will cause inaccuracy.

SAFETY INSTRUCTION

Before putting the device into use, please read with care the
information given in the Operating Instructions. They contain
important instructions for installation, proper use and maintenance
of the device.
The manufacturer shall not be liable for damages arising out of
failure to heed the following instructions:

 When using electrical components under increased safety

requirements, always comply with the appropriate regulations.

 Improper installation will render the warranty null and void.
 Ensure the voltage marked on the power supply unit matches

your mains power supply.

 This device is designed for use indoors.
 Observe the permissible ambient temperatures for use
 The device meets the requirements for electromagnetic

compatibility. Do not exceed the maximum values specified in
the applicable standards.

If you have any problem, please contact your local CHARDER
MEDICAL service partner.

- 3 -

ENVIRONMENTAL

 All batteries contain toxic compounds; disposal of batteries

should be delegated to a competent organisation, complying
with the deposit of Poisonous Waste Regulation 1972.

 Please do not incinerate batteries.
 The optimum operating temperature for the scale is 5℃ to +35

℃; although it will operate at higher and lower temperatures the
scales battery life will be adversely effected.

CLEANING

 We would recommend using alcohol based wipes or similar

when cleaning the scales.

 Please do not use large amounts of water when cleaning the

scales as this will cause damage to the scales electronics, you
should also refrain from using corrosive liquids or high pressure
washers.

 Always disconnect the scales from the mains power supply

before cleaning.

MAINTENANCE

The scale does not require any routine maintenance. However, we
recommend checking the scale’s accuracy at regular intervals. The
regularity of these checks is dependent on the level of use and the
state of the scale. If any inaccuracies occur, please contact your
local dealer or CHARDER MEDICAL service partner.

- 32 -

INSTRUCTION FOR REPLACING BATTERIES

1. Removing the battery cover. 2. Take the battery housing out.

3. Replacing new batteries. 4. Batteries are well installed.

5. Installing the battery housing. 6. Reinstalling the battery
cover.

- 31 -

CAUTION:

 Always connect the AC adaptor with the indicator before

connecting to the mains power supply.

 Please disconnect the adaptor from main power supply before

taking out the AC adaptor pin from indicator.

INSTRUCTION FOR CHARGING AND
CONNECTING

If

prompt displays on the LCD, please charge the

scale with MS 4610 & 4600 exclusive adaptor or replace the
batteries.

Locate adaptor plug-in at the back side of indicator.

- 4 -

WEIGHING OPERATION

Before reading detailed instructions on how to use all the weighing
functions that are built into your scale, please read the following
important guidelines:
 Always be sure that the display shows `Zero` before use, if it
does not then please press the ZERO key.
 The device is designed to detect when a stable weight is
achieved, the indicator will `bleep` twice to indicate a stable weight
value, your reading should be taken at this point.

WARRANTY-LIABILITY

 If a fault or defect is present on receipt of the unit which is within
CHARDER MEDICAL’s scope of responsibility, CHARDER shall
have the right to either repair the fault or supply a replacement unit.
Replaced parts shall be the property of CHARDER. Should the fault
repairs or replacement delivery not be successful, the statutory
provisions shall be valid. The period of warranty shall be two years,
beginning on the date of purchase. Please retain your receipt as
proof of purchase. Should your scale require servicing, please
contact your dealer or CHARDER MEDICAL Customer Service.
No responsibility shall be accepted for damage caused through any
of the following reasons: Unsuitable or improper storage or use,
incorrect installation or commissioning by the owner or third parties,
natural wear, changes or modifications, incorrect or negligent
handling , overuse, chemical, electrochemical or electrical
interference or humidity, unless this is attributable to negligence on
the part of CHARDER MEDICAL.

- 5 -



If operating, climatic or any other influences lead to a major
change in conditions or material quality, the treaty for perfect unit
functioning shall be rendered null and void. If CHARDER
provides and individual warranty, this means that the unit
supplied will be free of faults for the length of the warranty
period.

DISPOSING OF THE SCALE

 This product is not to be treated as regular household waste, but

should be handed in to an electrical/electronic equipment

recycling centre.
You can obtain further details from your local council, your municipal
waste disposal company or the firm which you purchased the
product.

- 30 -

2. New Connection Description

Give new connection a name then click OK.

3. Select Your COM Port
Click Connect to select your COM port. Usually there’s only one
option for select. Then click OK.

4. Port Settings
Click Bits per second to set up rate at 9600, Data bits at 8, Parity at
None, Stop bits at 1 and Flow control at Hardware. Then click OK to
complete your setting.

5. Output Data
When the patient has been weighed and BMI calculated, simply
press the PRINT key to output data from scale to PC or an Optional
Printer.

Parameters of RS232 interface
Set parameters of the scale interface on the connected device. It is
not possible to change the scale parameters.

 Baud rate: 9600 bps
 Parity check: None
 Data length: 8 bits
 Stop bit: 1 bit
 Handshake: RTS/CTS
 Data code: ASCII.