Charbroil 463631704 Owner's Manual
Parts to assemble:
2 Leg Assembly
1 Front Panel
2 Side Support Brace
4 Carriage Bolt, 2”
4 Plastic Tee Knob
Leg Assembly
A. Lay leg assemblies on their sides.
B. Place front panel on legs.
C. Braces attach to inside of legs.
D. Secure with carriage bolts and tee knobs.
Front Panel
Parts to assemble:
1 Back Support Brace
21
4 Carriage Bolt, 2”
4 Plastic Tee Knob
A. Turn assembly upside-down.
B. Secure back brace and side
braces to legs with carriage
bolts and tee knobs.
3
Parts to assemble:
1 Tank Support Bracket
2 Wheel
2 Axle Bolt
2 Hitch Pin
2 Leg Extender
A. Insert axle bolts through wheels,
left legs and bracket. Bracket fits
inside legs.
B. Secure with hitch pins in ends
of axle bolts.
C. Push leg extenders into right legs.
Tank Support Bracket
Leg Extender
Wheel
4
Qty. 4
Qty. 4
Qty. 4
Side Support Brace
NOTE: To prevent scratching, lay grill on packing material to assemble.
Parts to assemble:
1 Grill Bottom Assembly
4 Carriage Bolt, 1¼”
4 Metal Wing Nut
2 Control Knob
A. Stand cart upright.
B. Make sure ignitor wire is connected
to ignitor.
C. Place grill bottom onto supports. Control
panel overlaps front panel.
D. Secure with carriage bolts and wing nuts.
E. Press control knobs onto valves.
Ignitor
Wire
Grill Bottom
Control Knobs
Control Panel
Qty. 4
Qty. 4
5
Vaporiser Bar
Parts to assemble:
1 Vaporiser Bar
1 Cooking Grate
A. Place vaporiser bar onto the two inner
support ridges at each end of grill bottom.
Bar should rest between the outer support
ridges. See inset below.
B. Place cooking grate onto grill bottom.
Side braces on
inside of legs.
Cooking Grate
NOTE:
Ceramic briquets are not required.
Outer
Support
Ridge
Back Support Brace
Qty. 2 Qty. 2
6
Parts to assemble:
2 Side Shelf
8 Carriage Bolt, 2”
8 Crown Fasteners
or Plastic T Knobs
Qty. 8
OR
A. Place shelves onto legs (curved edge inward).
B. Secure with carriage bolts and crown fasteners
or T knobs.
Side Shelf
Curved Edge
Qty. 4
7
Qty. 2
Parts to assemble:
1 Grill Lid
1 Handle
1 Logo Plate
2 Metal Wing Nut
2 Hinge Pin
2 Hitch Pin
A. Attach lid to grill bottom with
hinge and hitch pins.
B. Attach handle to lid with two
metal wing nuts.
C. Snap logo plate into lid.
Qty. 2
Logo Plate
Handle
Grill Lid
(Lid style may vary)
8
Parts to assemble:
1 SwingAway
A. Slide rear pivot wire of
SwingAway into holes
in grill lid.
B. Insert leg wires into top
hole of three-hole pattern
in side of grill bottom.
Note: Wires at rear of
SwingAway should point
upward.
SwingAway
Qty. 8
9
Qty. 1
Qty. 8
Parts to assemble:
1 Tank Retainer Wire
1 Carriage Bolt, 1¼”
1 Plastic Tee Knob
A. Attach retainer wire to left
side brace with carriage bolt
and tee knob. Leave loose.
Tank
Retainer
Wire
Qty. 2
Parts to assemble:
1 LP Gas Tank
10
LP tank is shipped empty. Fill and
leak check before attaching to grill
and regulator.
A. Center LP tank on support bracket
with collar opening to front.
B. Slide retainer over tank collar and
tighten tee knob.
CAUTION
Tank collar opening must face to front of cart once
tank is attached.
Failure to install tank correctly may allow gas hose to
be damaged in operation, resulting in the risk of fire.
Tank Collar
LP Gas Tank
11
Parts to assemble:
1 Grease Clip
A. Hang grease clip
beneath grill bottom.
Rear view
of grill.
Grease Clip
Qty. 1
Parts to assemble:
1 Grease Cup
12
A. Attach grease cup to
grease clip.
CAUTION
• Failure to install cup in clip will cause hot grease to
drip from bottom of grill with risk of fire or property
damage.
Rear view
of grill.
See Use & Care manual to perform the
“Burner Flame Check” and for important
safety instructions before using.
Grease Cup
463631704
Loading...