Charbroil 461846104 Owner's Manual
1st: Unfold legs. Do not stand cart up until front panel is attached. The front panel stabilizes
1
1
the cart.
Items to Assemble:
2 Wheels
1 Tank Support
2 Axle Bolts
2 Hitch Pins
2 Hub Caps
1 Tank Retainer
1 1-1/4” Carriage Bolt
1 Wing Nut, Metal
3 Control Knobs
Qty: 1
Qty: 2
Bolt1-1/4” Carriage
Tank Retainer
2
Items to Assemble:
1 Upper Panel
4 2” Carriage Bolts
4 Wing Nuts
1 Lower Panel
3 2” Carriage Bolts
3 Wing Nuts
Lower Panel inserts into Upper Panel
Slide Upper Panel
under UFC
Stand Cart Upright
3
Items to Assemble:
1 Left Shelf
2 3/4” Carriage Bolts
2 Wing Nuts
2 Wing Screws
Repeat for Right Shelf
1 Right Shelf
2 3/4” Carriage Bolts
2 Wing Nuts
2 Wing Screws
View looking down
Insert 3/4” Carriage Bolts into bracket on Legs
Qty:4
4
Qty: 1
Item to Assemble:
1 Condiment Wire
1 Condiment Tray
A
Qty: 2
Wheel attaches
in BOTTOM HOLE
on legs
Tank Support
Hub on wheel faces into leg.
Attach in bottom hole on leg
with axle bolt and hitch pin.
5
B
Qty: 7
Items to Assemble:
3 Tent Frames
3 Burner Tents
2 Grates
Qty: 7
Grates
Burner Tents
Tent Frames
Qty:4
6
Qty:4
Items to Assemble:
1 Grill Lid
2 Hinge Pin
2 Hitch Pin
Hinge Pin
and Hitch Pin
Qty: 2
Qty: 2
Make sure all
tabs are inside slots
before fastening
four
7
Items to Assemble:
1 Logo Plate
1 Temp Gauge Bezel
1 Temperature Gauge w/Wing Nut
Items to Assemble:
8
1 Handle Assembly
1 Right Lamp Assembly
1 Left Lamp Assembly
Note: On the underside of the lamp assemblies are “L” for left side
and “R” for right side. Match to letters on the handle.
Attach right and left lamp assemblies to lid with either thumbscrews
or Phillips head screws provided. Do not overtighten screws.
Overtightening will cause handle to crack.
CAUTION: To prevent a shorting condition make sure
the lamp assemblies are fully inserted into casting.
Screw
Casting
Screw
L
L
Left Lamp
Assembly
Casting
NO GAP
Left Lamp
Assembly
Or
Items to Assemble
9
1 Chef’s Delite
2 Swing Grid Bolts
9
2 Wing Nuts, Metal
“L”
Left
“R”
Right
or
or
Metal
Qty: 2
Qty: 2
Items to Assemble:
10
10
Loosen wing nut on tank retainer. Center base of LP tank
A
in notches on the tank support. Lower tank holder onto tank
and tighten the wing nut.
B
Place “AAA” battery into module, secure with button.
Button
1 LP Tank (purchased)
1 AAA Battery
B
+
–
Battery
A
INCORRECT ASSEMBLY
LP tank is sold separately. Use only with an (over-fill protection
device) OPD equipped LP tank. Fill and leak check before attaching
to grill and regulator.
See Use & Care to perform the “Burner Flame Check” and
important safety instructions before using.
!
CAUTION
• Tank collar opening must face to front of cart
once tank is attached.
• Failure to install tank correctly may allow gas
hose to be damaged in operation, resulting in
the risk of fire.
11
CORRECT ASSEMBLY
Items to assemble:
1 Chain with Coupling
1 Match-Holder
1 Grease Clip
1 Grease Cup
Back of Grill
Grease Clip
Grease Cup
Hang grease clip from center of grill bottom.
Use an empty soup can to hang from grease clip.
See Use & Care Manual for “Match Lighting Instructions”
Place end of chain through hole, reattach coupling to end of chain.
Thread eyelet on other end of chain into loop of match holder.
!
CAUTION
• Failure to install can in clip will cause hot
grease to drip from bottom of grill with
risk of fire or property damage.
Remove coupling from chain
Eyelet End
Eyelet End
Match-Holder
Match-Holder
12
461846104
Loading...