Charbroil 461742204 Owner's Manual
1
1
Qty: 6
Items to Assemble:
2 Leg Assemblies
1 Bottom Shelf
6 Carriage Bolts
6 Wing Nuts
Left Side:
Place 1 Carriage Bolt
and Wing Nut in upper hole only
Place Bottom Shelf and Legs as shown.
After assembling tighten all Wing Nuts.
Items to Assemble:
2
Attach Wheels with Hitch Pins
2 Wheel Assemblies
2 Hitch Pins
2 Leg Extenders
Qty: 2
Item to Assemble:
1 Wire Shelf
3
1 Panel
2 Push Pins
A Place Wire Shelf in 3rd hole from top.
Assemble front panel first by
B
placing tabs into slots on Bottom Shelf.
Attach with push pins.
A
B
4
Qty: 6
Items to Assemble:
1 Grill Bottom
1 Heat Shield
2 Carriage Bolts
2 Wing Nuts
2 Control Knobs
Qty.2
Right Side:
Attach 2 Carriage Bolts and Wing Nuts in
front and back.
5
Items to Assemble:
1 Right Shelf
4 Wing Screws
6
Qty: 2
Items to Assemble:
2 End Caps
1 Toolholder
1Carriage Bolt
1 Wing Nut
Place Carriage Bolt in right hole on Toolholder. Secure with Wing Nut.
Qty: 1
7
Qty. 2
Items to Assemble:
1 Sideburner Body
1 Sideburner Frame
1 Carriage Bolt
1 Wing Nut
1 Crown Screw or Wing Nut
or
Join Sideburner Body and Frame. In back center hole attach with Carriage Bolt and Wing Nut.
In front use a Crown Screw or Wing Nut to attach Toolholder and Sideburner Body.
Qty: 1
Qty: 4
Items to Assemble:
8
A
Place Sideburner into hole.
B
Attach Sideburner Valve Cup. Make sure
Sideburner Tube is inside of valve. Tighten
with Wing Nut.
C
Place Sideburner Knob and Grate
D
Attach long wire from beneath console
to electrode beneath Sideburner.
1 Sideburner
1 Wing Nut
1 Sideburner Valve Cup
1 Sideburner Knob
1 Sideburner Grate
Qty: 1
Qty: 1
Items to Assemble:
1 V-Bar
9
9
C
A
10
Qty: 1
Items to Assemble:
1 Grill Lid
2 Hinge Pins
2 Hitch Pins
1 Handle
2 Wing Nuts
1 Logo Plate
1 Temp Gauge Bezel
1 Temperature Gauge
w/Wing Nut
Qty: 2
Qty: 2
Qty:2
Qty: 1
Hinge Pin
and Hitch Pin
Qty: 1
Note: Grill lid
style may vary.
B
Correctly assembled Sideburner Tube in Valve
Items to Assemble:
11
A
Insert pivot wire of Lower Warming Rack into Lid.
Flex leg wires to insert into Grill bottom.
B
Insert pivot wire of Upper Warming Rack into lid.
Flex leg wires to insert into loops on Lower Rack.
C
Place grate.
1 Lower Warming Rack
1 Upper Warming Rack
1 Grate
B
Leg wires on both Warming Racks
must run underneath surfaces.
Legs snap into loop
D
12
Items to Assemble:
1 Grease Clip
1 Tank Wire Support Bracket
See Use & Care Manual for “Match Lighting Instructions” and to
perform the Burner Flame Check” and important safety
Push V-Bar down onto
rest in Grill Bottom
instructions before using.
Hang grease clip from center of grill bottom.
Use an empty soup can (not included) to hang
from grease clip.
Back of Grill
LP tank is sold separately. Use only with an
(over-fill protection device) OPD equipped LP Tank.
Fill and leak check before attaching to grill and regulator.
!
CAUTION
C
Grate
A
• Failure to install can in clip will cause hot grease
to drip from bottom of grill with risk of fire or
property damage.
• Tank collar opening must face to front of cart
once tank is attached.
• Failure to install tank correctly may allow gas
hose to be damaged in operation, resulting in
the risk of fire.
461742204
Loading...