Charbroil 461740304 Owner's Manual
Qty. 4
Parts to assemble:
2 Leg Assembly
1 Front Panel
1 Side Support Brace
4 Carriage Bolt, 2”
4 Plastic Tee Knob
Leg Assembly
A. Lay leg assemblies on their sides.
B. Place front panel on legs.
C. Braces attach to inside of legs.
D. Secure with carriage bolts and tee knobs.
Leave tee knobs loose on right side.NOTE:
Front Panel
Side Support Brace
(Fits inside legs.)
Leave these loose.
2 31
Qty. 4
Parts to assemble:
1 Back Support Brace
4 Carriage Bolt, 2”
4 Plastic Tee Knob
2 Wheel Assembly
1 Tank Support Bracket
2 Hitch Pin
2 Leg Extender
A. Turn assembly upside-down.
B. Secure back brace and side brace to left leg
and back brace to right leg with carriage bolts
and tee knobs. Leave tee knobs loose
on right side.
C
. Insert wheel assemblies into legs and bracket.
Bracket fits inside legs.
D. Secure with hitch pin in axle bolt hole closest to leg.
E. Push leg extenders into right legs.
NOTE:
Qty. 2
Wheel Assembly
Tank
Support
Bracket
Leg Extender
Back
Support
Brace
Parts to assemble:
1 Condiment Basket
A. Stand cart upright.
B. Place condiment basket
hooks over front panel bolts
on inside of front leg.
See inset .
C.. Place condiment basket
hooks over back support
brace bolts on outside of
brace. See inset .
D.. Fully tighten tee knobs
on both legs.
A
B
B
A
Condiment
Basket
4
Qty. 4
Qty. 4
NOTE: To prevent scratching, lay grill on packing material to assemble.
Parts to assemble:
1 Grill Bottom Assembly
4 Carriage Bolt, 1¼”
4 Metal Wing Nut
2 Control Knob
A. Make sure ignitor wire is connected
to ignitor.
B. Place grill bottom onto supports. Control
panel overlaps front panel.
C. Secure with carriage bolts and wing nuts.
D. Press control knobs onto valves.
Ignitor
Wire
Grill Bottom
Control Knobs
Control Panel
5
Qty. 4
Parts to assemble:
1 V Bar
1 Cooking Grate
A. Place V bar onto supports at each
end of grill bottom.
B. Place cooking grate onto grill bottom.
Cooking Grate
V Bar
6
Parts to assemble:
2 Side Shelf
8 Carriage Bolt, 2”
8 Crown Fasteners or
Plastic T Knobs
Qty. 8
OR
Qty. 8
A. Place shelves onto legs (curved edge inward).
B. Secure with carriage bolts and crown fasteners
or plastic T knobs.
Curved Edge
Side Shelf
Qty. 4
7
Qty. 2
Parts to assemble:
1 Grill Lid
1 Handle
1 Logo Plate
2 Metal Wing Nut
2 Hinge Pin
2 Hitch Pin
A. Attach lid to grill bottom with
hinge and hitch pins.
B. Attach handle to lid with two
metal wing nuts.
C. Snap logo plate into lid.
Qty. 2
Logo Plate
Handle
Grill Lid
(Lid style may vary)
NOTE:
Ceramic briquets are not required.
Parts to assemble:
1 Warming Rack
8
A. Slide rear pivot wire of
warming rack into holes
in grill lid.
B. Insert leg wires into top
hole of three-hole pattern
in side of grill bottom.
Note: Wires at rear of
warming rack should point
upward.
Warming Rack
Qty. 8
9
Qty. 1
Parts to assemble:
1 Tank Retainer Wire
1 Carriage Bolt, 1¼”
1 Plastic Tee Knob
A. Attach retainer wire to left
side brace with carriage bolt
and tee knob. Leave loose.
Tank
Retainer
Wire
Qty. 2
10
Parts to assemble:
1 LP Gas Tank
(not included)
LP tank is sold separately. Fill and
leak check before attaching to grill
and regulator.
A. Center LP tank on support bracket
with collar opening to front.
B. Slide retainer over tank collar and
tighten tee knob.
CAUTION
Tank collar opening must face to front of cart once
tank is attached.
Failure to install tank correctly may allow gas hose to
be damaged in operation, resulting in the risk of fire.
Tank Collar
LP Gas Tank
Parts to assemble:
1 Grease Clip
11
A. Hang grease clip
beneath grill bottom.
B. Hang an empty soup
can (not included) from
grease clip.
CAUTION
• Failure to install can in clip will cause hot grease to
drip from bottom of grill with risk of fire or property
damage.
Rear view
of grill.
Qty. 1
Grease Clip
See Use & Care manual to perform the
“Burner Flame Check” and for important
safety instructions before using.
461740304
Loading...