Charbroil 461733803 Owner's Manual
1
Qty. 4
Parts to assemble:
2 Leg Assembly
1 Front Panel
1 Side Support Brace
4 Carriage Bolt, 2”
4 Plastic Tee Knob
Leg Assembly
A. Lay leg assemblies on their sides.
B. Place front panel on legs.
C. Braces attach to inside of legs.
D. Secure with carriage bolts and tee knobs.
Leave tee knobs loose on right side.NOTE:
Front Panel
Side Support Brace
(Fits inside legs.)
Leave these loose.
Parts to assemble:
1 Back Support Brace
2 3
Qty. 4
4 Carriage Bolt, 2”
4 Plastic Tee Knob
2 Wheel Assembly
1 Tank Support Bracket
2 Hitch Pin
2 Leg Extender
A. Turn assembly upside-down.
B. Secure back brace and side brace to left leg
and back brace to right leg with carriage bolts
and tee knobs. Leave tee knobs loose
on right side.
C
. Insert wheel assemblies into legs and bracket.
Bracket fits inside legs.
D. Secure with hitch pin in axle bolt hole closest to leg.
E. Push leg extenders into right legs.
NOTE:
Qty. 2
Wheel Assembly
Tank
Support
Bracket
Leg Extender
Back
Support
Brace
Parts to assemble:
1 Condiment Basket
A. Stand cart upright.
B. Place condiment basket
hooks over front panel bolts
on inside of front leg.
See inset .
C.. Place condiment basket
hooks over back support
brace bolts on outside of
brace. See inset .
D.. Fully tighten tee knobs
on both legs.
A
B
B
A
Condiment
Basket
4
Qty. 4
Qty. 4
NOTE: To prevent scratching, lay grill on packing material to assemble.
Parts to assemble:
1 Grill Bottom Assembly
4 Carriage Bolt, 1¼”
4 Metal Wing Nut
A. Stand cart upright.
B. Make sure ignitor wire is connected
to ignitor.
C. Place grill bottom onto supports. Control
panel overlaps front panel.
D. Secure with carriage bolts and wing nuts.
Ignitor
Wire
Grill Bottom
Control Panel
5
Qty. 4
Parts to assemble:
1 V Bar
1 Cooking Grate
A. Place V bar onto supports at each
end of grill bottom.
B. Place cooking grate onto grill bottom.
Cooking Grate
V Bar
6
Parts to assemble:
2 Side Shelf
8 Wing Screw
A. Place shelves onto
legs.
B. Secure with four wing
screws per shelf.
Side Shelf
Qty. 4
7
Qty. 2
Parts to assemble:
1 Grill Lid
1 Handle
1 Logo Plate
2 Metal Wing Nut
2 Hinge Pin
2 Hitch Pin
A. Attach lid to grill bottom with
hinge and hitch pins.
B. Attach handle to lid with two
metal wing nuts.
C. Snap logo plate into lid.
Qty. 2
Logo Plate
Handle
Grill Lid
(Lid style may vary)
NOTE:
Ceramic briquets are not required.
Parts to assemble:
1 Lower Warming Rack
8
A. Slide rear pivot wire of lower warming rack
into lower holes in side of grill lid.
B. Insert leg wires into top hole of three-hole
pattern in side of grill bottom.
C. Slide rear pivot wire of upper
warming rack
grill lid.
D. Insert leg wires into loop on sides of
lower .
warming rack
1 Upper Warming Rack
into middle holes in side of
Upper
Warming Rack
Note: Wires at rear of
warming racks should
point upward.
Lower
Warming Rack
9
Qty. 1
Qty. 8
Parts to assemble:
1 Tank Retainer Wire
1 Carriage Bolt, 1¼”
1 Plastic Tee Knob
A. Attach retainer wire to side
brace with carriage bolt and
tee knob. Leave loose.
Tank
Retainer
Wire
Qty. 2
10
Parts to assemble:
1 LP Gas Tank
(sold separately)
LP tank is sold separately. Fill and
leak check before attaching to grill
and regulator.
A. Center LP tank on support bracket
with collar opening to front.
B. Slide retainer over tank collar and
tighten tee knob.
CAUTION
Tank collar opening must face to front of cart once
tank is attached.
Failure to install tank correctly may allow gas hose to
be damaged in operation, resulting in the risk of fire.
Tank Collar
LP Gas Tank
Parts to assemble:
1 Grease Clip
11
A. Hang grease clip
beneath grill bottom.
B. Hang an empty soup
can (not included) from
grease clip.
CAUTION
• Failure to install can in clip will cause hot grease to
drip from bottom of grill with risk of fire or property
damage.
Rear view
of grill.
Qty. 1
Grease Clip
See Use & Care manual to perform the
“Burner Flame Check” and for important
safety instructions before using.
461733803
Loading...