CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in material or
workmanship whichoccurs during normal use of this product with new or rebuilt
parts, freeof charge in the USA, for two years from the date of original purchase.
This is a no hassle warranty with no mail in warranty card needed.This warranty
does not cover damages in shipment, failures caused by other products not
supplied by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only to the
original purchaser, and a purchase receipt, invoice, or other proof of original
purchase date will be requiredbefore warranty repairsare provided.
Mail in service can be obtained during the warranty period by calling (800) 840-
0288 toll free. AReturn Authorization number must be obtained in advance and
can be marked on theoutside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with thisproduct developsduring or
after the warranty period, please contact Channel VisionTechnology, your dealer
or any factory-authorized service center.
The IR-5000 includes these items:
Power supply
1 - hole mount
2 - IR-3002 emitters
How IR repeating works
The IR receiver is wired to
the IR hub which routes the
signal to IR emitters
>
>
F
F
e
t
t
s
a
u
a
B
P
x
>
T
y
a
l
P
p
3
o
t
S
<
<
6
w
e
R
n
r
a
e
L
-
-
5
/
l
12
Vo
89
r
4
o
r
0
r
E
h
C
n
7
r
f
a
r
f
e
e
O
L
w
l
l
o
A
P
t
c
e
l
e
S
r
e
n
Tu
And the emitter
repeats the IR signal
in front of the component.
IR remote control
at the IR receiver
f
f
O
t
a
S
V
T
D
C
TM
D
V
D
0
0
R
C
V
-5
B
A
ChannelVision
Point an
CD player
Specifications
Specifications: (typical)
Power Supply Voltage:
IR Freq. range supported:
IR pickup range:
IR receiver head dimensions:
IR emitter outputs:
Color:
Specifications subject to change without notice.
8-12VDC
30 kHz - 60 kHz
40 ft. @ 38kHz, 25 ft. @ 56kHz
0.65” x 0.35” x 0.25”
4
Black
500-149 rev B
1 - tabletop mount
IR receiver head
36”
Features:
!
Plasma Proof IR receiver
!
4 IR emitters
!
Status LEDs for power and IR signal indication
!
Versatile mounting accessories included
4 - IR emitter holsters
1 - IR receiver holster
LED Status indicators:
Power and IR data
DC Power input
Be sure the emitter is attached directly over the component’s IR receiver.
To locate the IR receiver, shine a flashlight into the unit and look for the
sensor.
4 IR emitter outputs
CD player
Mounting the IR emitter
Remove the backing from the tape and attach the
IR emitter holster over the IR sensor of the device
you wish to control.
Mounting the IR receiver: Option 1 - Using the holster
Mount the IR receiver to the TV or on a surface within line of sight
of your remote control.
Remove the backing from the tape and attach the
IR receiver holster in the desired location.
Snap IR emitter into the holster
as shown.
Drill a 3/4” .hole
Push the IR receiver head
through the hole.
Insert the IR receiver head
into the IR receiver hole mount.
Mounting the IR receiver: Option 3 - Using the tabletop mountMounting the IR receiver: Option 2 - Using the hole mount
Push the IR receiver head
through the hole in the
tabletop mount.
Insert the IR receiver head
into the IR receiver hole mount.
Snap IR receiver head into the holster
as shown.
Push the IR receiver hole
mount and IR receiver head
back into the hole in the tabletop
mount.
To secure the mount, remove
the backing from the foam tape
on the bottom of the unit and
attach the mount to any flat surface.
Push the IR receiver hole
mount and IR receiver head
back into the hole.
Loading...