Channel Vision IR-2005 User Manual
CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in material or
workmanship whichoccurs during normal use of this product with new or rebuilt
parts, freeof charge in the USA, for two years from the date of original purchase.
This is a no hassle warranty with no mail in warranty card needed.This warranty
does not cover damages in shipment, failures caused by other products not
supplied by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only to the
original purchaser, and a purchase receipt, invoice, or other proof of original
purchase date will be requiredbefore warranty repairsare provided.
Mail in service can be obtained during the warranty period by calling (800) 840-
0288 toll free. AReturn Authorization number must be obtained in advance and
can be marked on theoutside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with thisproduct developsduring or
after the warranty period, please contact Channel VisionTechnology, your dealer
or any factory-authorized service center.
500-181 rev A
IR-2005
(rear view)
The IR-2005 includes these items:
Screwless decorator style trim ring
Single-gang decorator style IR wall plate
IR-2400 Plasma proof IR receiver
IR-2005
(front view)
How IR repeating works
The IR receiver is wired to
the IR hub which routes the
signal to IR emitters
>
t
>
t
F
a
F
B
x
e
T
s
u
a
>
y
P
a
l
P
p
o
t
<
S
<
w
e
R
3
n
r
a
e
L
2
6
1
9
5
/-
-
8
4
l
Vo
7
0
r
h
e
C
w
r
o
o
P
r
r
E
n
r
a
e
L
f
f
O
l
l
A
f
f
O
t
a
S
V
T
D
t
C
c
e
l
e
S
D
V
r
e
D
n
Tu
R
C
V
n
sio
an
xp
E
e
n
Zo
bal
lo
G
r
Pw
Model
IRReceiver
P-1205
M
T
HANNEL
C
ISION
V
l
a
b
lo
G
IR
r
e
v
i
e
Emitters
c
e
R
e
n
o
Z
C
D
2
1
A
+
m
0
5
2
And the emitter
IR remote control
at the IR receiver
CD player
repeats the IR signal
in the other room.
Be sure the emitter is attached directly over the
component’s IR receiver. To locate the IR receiver, shine a
flashlight into the unit and look for the sensor.
Point an
Specifications (typical)
Voltage requirements:
IR Freq. range supported:
IR pickup range:
Mounting requirements:
Color:
Specifications subject to change without notice.
8-12VDC
30 kHz - 60 kHz
40 ft. @ 38kHz, 25 ft. @ 56kHz
Single-gang box or ring
White
IR receiver window
Features:
!
Plasma Proof IR receiver
!
Status LEDs for IR signal indication
!
Mounts in a single-gang box or low-voltage ring
IR-2005
(rear view)
Single Room IR Setup
A single room IR system can be created by connecting the IR2005 with the P-1205. Connect the three screw terminals on
the P-1205 to the screw terminals on the IR-2005 using a 3conductor wire (18-24AWG). CAT5 wire can be used, but
only 3 of the 8 conductors are needed.
IR-2005
(rear view)
IR1
IR2 IR3 IR4 IR5 IR6 IR7 IR8
-
+
+
S
S
Whole-House IR Setup
IR-2005
IR-2005
-
-
-
-
-
-
+
+
+
S
S
+
S
S
-
+
+
S
S
3-conductor
18-24 AWG wire
Pwr
IR Receiver
Expansion
G
Zone
lobal
Model
P-1205
HANNEL
HANNEL
C
C
ISION
ISION
V
V
IR
Receiver
+12DC
IR BUS
CVHANNEL ISION
Central
TM
+-+
POWER
-
S
C-1201
12
4
3
5
7
Po
6
wer
89
0
Additional
IR receivers can
be connected
as needed.
3-conductor
TM
TM
Global
Em
itters
Sat radio
DVD player
Zone
CD player
18-24 AWG wire
Pwr
IR Receiver
Expansion
Global
Zone
Model
P-1205
HANNEL
HANNEL
C
C
ISION
ISION
V
V
IR
Receiver
+12DC
TM
TM
Emitters
Global
Sat radio
DVD player
Zone
CD player
Receiver
Receiver
The diagram above illustrates how to create an IR system with IR receivers in
several different rooms in the house. Systems like this may include several different
styles of IR receivers depending on the specific application in each room.
Loading...