CHANNEL VISION
Limited Warranty
The IR-1203 includes these items:
Channel Vision Technology will repair or replace any defect in material or
workmanship whichoccurs during normal use of this product with new or rebuilt
parts, freeof charge in the USA, for two years from the date of original purchase.
This is a no hassle warranty with no mail in warranty card needed.This warranty
does not cover damages in shipment, failures caused by other products not
supplied by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only to the
original purchaser, and a purchase receipt, invoice, or other proof of original
purchase date will be requiredbefore warranty repairsare provided.
Mail in service can be obtained during the warranty period by calling (800) 840-
0288 toll free. AReturn Authorization number must be obtained in advance and
can be marked on theoutside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with thisproduct developsduring or
after the warranty period, please contact Channel VisionTechnology, your dealer
or any factory-authorized service center.
500-198 rev A
IR-1203
Expansion/Receiver
Inputs
Features:
!
4 IR emitter outputs
!
Status LEDs for power and IR signal indication
!
Screw terminal or mini-plug connections for IR receivers
!
Easily mounts to any flat surface
Power supply
LED Status Indicators:
Power and IR data
DC Power Input
4 IR emitter outputs
How IR repeating works
The IR receiver is wired to
the IR hub which routes the
signal to IR emitters
>>
Batt
F
F
x
T
e
s
y>
a
Pau
Pl
p
<
<
Sto
Rew
3
arn
e
L
2
6
1
5
9
4
--
-/
8
l
Vo
7
0
er
w
Ch
Po
r
Erro
arn
e
L
f
f
O
All
fSele
f
O
Sat
ct
V
CD
T
er
n
DVD
Tu
Point an
IR remote control
at the IR receiver
Be sure the emitter is attached directly over the component’s IR receiver.
To locate the IR receiver, shine a flashlight into the unit and look for the
sensor.
VCR
And the emitter
repeats the IR signal
in front of the component.
CD player
Specifications
Specifications: (typical)
Power Supply Voltage:
IR Freq. range supported:
Maximum IR receivers:
Dimensions:
IR emitter outputs:
Color:
Specifications subject to change without notice.
8-12VDC
30 kHz - 60 kHz
8
1.10” x 1.03” x 4.25”
4
Black
Typical Operation
Up to 1000’
(tested with CAT-5e)
Power LED
IR data LED
IR-2400
Using IR-3002,
up to 8 IR emitters
may be controlled
Alternative Receiver Hookup
Direct plug-in cable
(Included with IR-2400)
When connecting IR receivers to the IR-1203,
there are two valid methods.
Method 1: Use the 3-wire screw terminal
connections as shown in the “Typical Application”
diagram.
Method 2: Use the direct plug-in cable provided
with the IR receiver.
Multiple Receiver Operation
To simplify the connection of multiple IR receivers,
a connecting block such as model C-1201(not shown)
can be used. The C-1201 can provide connections for
up to 8 IR receivers, allowing them all to connect to
the IR-1203.
Connect all S, G and +V together.
May connect up to 8 receivers.
Standard stereo
mini-plug cable
One power adaptor
powers both units
Using IR-3002,
up to 16 IR emitters
may be controlled
One power adaptor
for every 2 IR-2103
Emitter Expansion Application 2Expanding Into 2 Hubs
Note that only
S and G
are connected
One power adaptor
for every 2 IR-2103
Using IR-3002,
up to 32 IR emitters
may be controlled
Loading...