Channel Vision iBus AB-311 Instructions Manual

AB-311

TM

iPod Wall-Dock for A-BUS

By

TM

2

Slide-out Cradle
Provides support for the iPod
and holds the omni connector.
The support ledge slides into
the AB-311 when not in use.

Support Clip
Hold the top of the iPod securely.
2 support clips are supplied:
1 for iPod mini and 1 for other iPod models

Hub with Power Supply:

Amplified Keypad:

Speakers:

In-ceiling, In-wall and free standing 8 ohm speakers are acceptable.

Omni Connector

TM

Delivers power to the iPod for charging and provides audio to the A-BUS
whole-house audio system.

Features:

TM

!

Compatible with all standard A-BUS systems

!

Charges the iPod

TM

!

Senses audio to automatically override the main A-BUS source

Made For iPods with dock connector:

!

iPod photo

!

iPod mini

!

4th Generation iPod with omni (dock) connector

!

3rd Generation iPod with omni (dock) connector

This product is compatible with all Channel Vision A-BUS products as
well as all 3rd party products that carry the A-BUS Logo.

The AB-311 is not a standalone device. It must be installed as part of an

TM

A-BUS system which requires the following components:

TM

CHANN EL V ISI ONTMCHANN EL V ISI ON

byby

ININ

OUTOUT

11

22

TM

The AB-311 is an A-BUS local input module that was specially designed

R R R

for the Apple iPod and iPod mini . The attractive wall mount remains
unobtrusive while not in use, yet its support ledge with integrated Omni
connector slides out easily, ready to dock your iPod at all times. (See
Made For section on page 3 for a complete list of compatible iPods.)

3

Hub with Power Supply:

AB-404 P-1014

(power supply included)

AB-T2454

OR

AB-114

AB-202

Amplified Keypad:

Single Source Input Module:

Speakers:

In-ceiling, In-wall and free standing 8 ohm speakers are acceptable.

Made For iPods with dock connector:

!

iPod photo

!

iPod mini

!

4th Generation iPod with omni (dock) connector

!

3rd Generation iPod with omni (dock) connector

TM

This product is compatible with all Channel Vision A-BUS products as

TM

well as all 3rd party products that carry the A-BUS Logo.

The AB-311 is not a standalone device. It must be installed as part of an

TM

A-BUS system which requires the following components:

Compatibility

Other Required Components

TM

TM

CHANN EL V ISI ONTMCHANN EL V ISI ON

byby

ININ

OUTOUT

11

22

33

44

BRN

WHT/BRM

BLU

WHT/BLU

GRN

WHT/GRN

ORG

WHT/ORG

1 -

i

u

o

Mo

u

4 A BUS

Distr b

ti

n

d le

odel

M

P-1

14

0

+2

VD4 C

Pow r

e

+12VDC

t

s

Stau

steSy m

S ste

y

m

Input

cal

Lo

u

Inp

t

one 1

Z

2Zone

Zone 3

one 4

Z

x

nsionE

pa
O p

t

ut u

Local

Priority

Signal

L

R

mitters

E

P

R

O

N

N

E

CH

A L

TM

V

I

SIO N

N

N

E

CH

A L

V

I

SIO N

TM

IR

x

TM

By C HAN NEL VIS IO N

AUDIO

L

R

STATUS
12VDC

AB-202

A-BUS OUTPUT

STATUS

IR

IR EMITTERS

System Wiring Diagram

Using the AB-311 local source input module

4

AB-114

AB-311

(Rear)

1. Mount the AB-311 in a low

voltage ring or junction box.

3. Select the appropriate support clip for your iPod
Note: there are 2 support clips provided to accommodate
both standard iPods and the iPod mini

AB-311

(Front)

Speakers

OUT

T

OU

IN

I

N

1

A- r Modu

l

4 BUS Dist ibution

e

Mo

d

l e

1

14

P-

0

V+24 DC

Power

12V+

DC

S s

tatu

Sys em

t

Sys

em

t

Input

L

al

oc

I u

np

t

Zone 1

e Zon 2

Z

e 3on

Zone

4

E s

xpan

ion

p

Out

ut

cLo

al

Priority

Signal

L

R

Em tters

i

P O

R

HA N E

L

C N

M
T

S

O

NVI

I

HA N E

L

C N

S

O

NVI

I

M
T

IR

x

Tape Monitor or
Room 2 output

(Optional) IR emitters

Sat radio

DVD player

CD player

Receiver

Installation

5

1. Mount the AB-311 in a low

voltage ring or junction box.

3. Select the appropriate support clip for your iPod
Note: there are 2 support clips provided to accommodate
both standard iPods and the iPod mini

Support Clips

2. Install the trim ring.

IN

OUT

6

iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.

A-BUS is a register trademark of LeisureTech Electronics Pty Ltd

4. Open the slide-out cradle and dock your iPod.

5. Enjoy your music!

Slide-out Cradle

Connections:

AB-311

(shown with iPod mini installed next to AB-114 keypad)

Specifications: (typical @25º C)
Operating Voltage : 24±.5VDC
Cable requirements: CAT-5 or better
Operating Temperature: -10ºC to +50ºC

Specifications subject to change without notice.

Trouble?

1) Be sure you have connected the CAT-5 cable correctly. Note that the
stripe/solid pattern should match the labels on the product. Miss-wiring
can cause distorted sound or prevent the system from working at all!

2) Be sure you have connected the speakers in phase. Follow the label
on the product. Out of phase speakers can rob the system of its bass.
Especially when driving dual-voice-coil speakers.

Connection Tips and Troubleshooting

Input/Output ... To simplify installation, the

AB-311 has both 110 and RJ-45 inputs and
outputs. Only one of the inputs and one of the
outputs should be used at a time.

Cat5

1. Place the CAT-5 between the blade and the first notch of the J-110 tool.

CAT-5 cable should be stripped with a proper stripping tool, such as Channel
Vision’s J-110 tool.

3. Inspect the inner wires for damage.
If any wires are cut start over at step 1.

Check for damage

4. Use any standard 110 punch-down tool to properly seat all wires.

Note: Do NOT use a screwdriver or any other tool that is not specifically
designed for terminating UTP cable. Using improper tools will damage
the connector!

7

iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.

A-BUS is a register trademark of LeisureTech Electronics Pty Ltd

Stripping and Connecting CAT-5 Wire

Specifications: (typical @25º C)
Operating Voltage : 24±.5VDC
Cable requirements: CAT-5 or better
Operating Temperature: -10ºC to +50ºC

Specifications subject to change without notice.

Blade

Cat5

1. Place the CAT-5 between the blade and the first notch of the J-110 tool.

CAT-5 cable should be stripped with a proper stripping tool, such as Channel
Vision’s J-110 tool.

Slight

pressure

Rotate

1 turn only

2. Rotate the tool only once around the CAT-5. Multiple

turns will cause you to cut into the inner wires.

3. Inspect the inner wires for damage.
If any wires are cut start over at step 1.

Check for damage

4. Use any standard 110 punch-down tool to properly seat all wires.

Note: Do NOT use a screwdriver or any other tool that is not specifically
designed for terminating UTP cable. Using improper tools will damage
the connector!

Channel Vision Technology will repair or replace any defect in

material or workmanship which occurs during normal use of this

product with new or rebuilt parts, free of charge in the USA, for two

years from the date of original purchase. This is a no hassle warranty

with no mail in warranty card needed. This warranty does not cover

damages in shipment, failures caused by other products not supplied

by Channel Vision Technology, or failures due to accident, misuse,

abuse, or alteration of the equipment. This warranty is extended only

to the original purchaser, and a purchase receipt, invoice, or other

proof of original purchase date will be required before warranty

repairs are provided.

Mail in service can be obtained during the warranty period by calling

[phone] toll free. A Return Authorization number must be

obtained in advance and can be marked on the outside of the shipping

carton.

This warranty gives you specific legal rights and you may have other

rights (which vary from state to state). If a problem with this product

develops during or after the warranty period, please contact Channel

Vision Technology, your dealer or any factory-authorized service

center.

500-111 revC