C-0441
CHANNEL VISION
Limited Warranty
110 Telecom Module
100 Pair Capacity
With Security Panel Loop
Alarm Bypass
T
R
Out
In
TM
To System
T
R
CHANNELVISION
Central
From Telco
To Alarm Panel
C-0441
Channel Vision Technology will repair or replace any defect in
material or workmanship which occurs during normal use of this
product with new or rebuilt parts, free of charge in the USA, for two
years from the date of original purchase. This is a no hassle warranty
with no mail in warranty card needed. This warranty does not cover
damages in shipment, failures caused by other products not supplied
by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only
to the original purchaser, and a purchase receipt, invoice, or other
proof of original purchase date will be required before warranty
repairs are provided.
Mail in service can be obtained during the warranty period by calling
(800) 840-0288 toll free. A Return Authorization number must be
obtained in advance and can be marked on the outside of the shipping
carton.
This warranty gives you specific legal rights and you may have other
CHANNEL VISION
234 Fischer Avenue · Costa Mesa, CA 92626
(714) 424-6500 · (800) 840-0288 · (714) 424-6510 fax
www.channelvision.com · email: sales @ channelvision.com
© 2003 Channel Vision Technology
TM
rights (which vary from state to state). If a problem with this product
develops during or after the warranty period, please contact Channel
Vision Technology, your dealer or any factory-authorized service
center.
500-007 rev B
The model C-0441 is a versatile, high capacity phone distribution panel
that mounts a standard 100 pair 110-type cross-connect block on a
structured wire module. A switch based security panel loop is provided
(more reliable than the typical RJ-31x jack).
Wiring the C-0441 for typical telephone use.
(24 telephone drops of 4 lines each.)
Cat-3 or Cat 5 cables
from phone jacks
around the house.
3) Untwist and position wires in slots 1-8 (extreme left).
Follow color code as shown. Note that the
white with color stripe wire is to the left of solid color.
Push the wires far into the
block so they will stay in place.
3a) Identify this cable and fill in the
upper left slot on the wiring list card.
1) Route first 12 cables
as shown
Alarm Bypass
T
R
Out
In
TM
To System
T
R
CHANNELVISION
Central
From Telco
To Alarm Panel
C-0441
2) Remove jacket from far left cable.
(Use sheath cutting tool.)
Alarm Bypass
T
R
Out
In
TM
To System
T
R
CHANNELVISION
Central
From Telco
To Alarm Panel
C-0441
4) Repeat for second cable.
Bed rm #2Bed rm #2
The wiring list card has two sides.
Use the side with 12 boxes.
Bed rm #2Bed rm #2
OfficeOffice
Bed rm #2Bed rm #2
OfficeOffice
2
3
4) Repeat for cables 3-12.
6) Use 4-pair impact tool to seat
110 blocks. Seat all blocks
on top two rows.
Alarm Bypass
T
T
R
Out
In
TM
To System
R
CHANNELVISION
Central
From Telco
To Alarm Panel
C-0441
5) Use 110 punch-down tool to seat
and trim all wires
Note position of cutter
Start with 8-pin (4-pair)
110 blocks at far left.
Note that some connectors have
10 pins (5 pair). Note the
sequence of connectors.
Note color codes.
8-pin 10-pin8-pin 8-pin 8-pin 8-pin
7) Wire the bottom two rows in the
same fashion. Slide wiring lists
into holders and snap into the frame.
You will now have up to 24 phone drops,
ready to cross-connect.
Caution: it is easy to place the
connectors upside down. Use
care when seating connectors.
Sequence of connectors
Bed rm #2Bed rm #2
OfficeOffice
Bed rm #3Bed rm #3
Kitchen northKitchen north
Slide into plastic holder
4
Entry Entry
Back porch #1Back porch #1 Master bed rtMaster bed rtMaster bed leftMaster bed left
Kitchen EastKitchen East
Master deskMaster desk
Master bdrm TVMaster bdrm TV
Master bathMaster bath
Snap plastic holder between rows.
5
7) Cross-connect 4 phone lines to all phone jacks.
Note slack in wire (service loop)
allows for changes in future.
Completely
wired panel
Alarm Bypass
T
R
Out
In
TM
Bed rm #2Bed rm #2
OfficeOffice
To System
T
R
Bed rm #3 NoBed rm #3 No
Bed rm #3 SoBed rm #3 So
Bed rm #3Bed rm #3
Kitchen northKitchen north
BasementBasement
Garage #1Garage #1
Entry Entry
Back porch #1Back porch #1 Master bed rtMaster bed rtMaster bed leftMaster bed left
Garage #2Garage #2
Lndry rmLndry rm
Kitchen EastKitchen East
Bed rm #4Bed rm #4
Liv rmLiv rm
Master deskMaster desk
Bed rm #5Bed rm #5
Bed rm #6Bed rm #6
Master bdrm TVMaster bdrm TV
Master bathMaster bath
Media ctr #1Media ctr #1
Media ctr #2Media ctr #2
CHANNELVISION
Central
From Telco
To Alarm Panel
C-0441
Snake wires back and forth to connect all phones to lines 1-4. Cross-connect wire
can be purchased at electrical supply houses or make by stripping back a length of
category cable.
NOTE: When you punch the wires down, remember to use the non-cutting
blade on 110 punch-down tool.
8) Connect to Security panel. Connect to Telco last.
In the normal position, the switch
From Teleco
From Telco
To Alarm Panel
Alarm Bypass
T
T
R
R
Out
In
will route line 1 to the security
panel. In alarm mode, the panel
will “seize” line one, disconnect
it from the rest of the house
and dial the alarm central
station using line.
If no security panel is used,
the switch should be
moved to the bypass
To System
position.
Media ctr #1Media ctr #1
Master bathMaster bath
Master bdrm TVMaster bdrm TV
Master deskMaster desk
Kitchen EastKitchen East
Back porch #1Back porch #1 Master bed rtMaster bed rtMaster bed leftMaster bed left
Entry Entry
Bed rm #3Bed rm #3
Kitchen northKitchen north
Bed rm #2Bed rm #2
OfficeOffice
Media ctr #2Media ctr #2
Bed rm #6Bed rm #6
Bed rm #5Bed rm #5
Liv rmLiv rm
Bed rm #4Bed rm #4
Garage #2Garage #2
Lndry rmLndry rm
BasementBasement
Garage #1Garage #1
Bed rm #3 SoBed rm #3 So
Bed rm #3 NoBed rm #3 No
To System
TM
To security panel
Blue/white = to panel TIP
Blue = to panel RING
Orange/white = from panel TIP
Orange = from panel RING
CHANNELVISION
Alarm Bypass
Central
6
R
T
In
R
T
Out
To Alarm Panel
C-0441
From Telco
7
Loading...