TM
IO
I N
LCH N
E V S
N
A
1
2
-02
C
l
e
d
o
M
ste
y ma i t u
S
i e
Wr
r d
u e
t
c
S r
ti n
sc
i
rbu o
s
B
d di t
n RF
e a
n
o
f rpho
h
oUse
unch-down to ls
p
1
nly 10
nnect rs
o
o oOt erto ls m
damage c
y
a
o
C-0221
Basic Structured Wire Module
The C-0221 is a basic structured wiring system that mounts in a standard
3-gang low-voltage ring. When viewed from the front, it appears to be a
blank 3-gang cover plate. Mounted to the back you will find everything
needed to satisfy the basic structured wiring needs of a small or mediumsized home. The 1x4 RF splitter provides TV signals to 4 locations while
the bridged phone module can distribute up to 4 CO lines out to as many
as 7 phone locations.
Features:
!
1 in 4 out RF splitter for TV signal distribution
!
Telephone distribution with 110 connectors: 4 CO lines to 7 locations
!
Compatible with standard 3-gang low-voltage rings
!
Cost effective and easy to install
Screw holes (4)...
Allow the C-0221 to be mounted to a standard 3-gang
low-voltage ring.
RF Input...
Connect CATV or antenna signals here.
M
T
N
O
I
IS
V
L
E
N
N
H
C A
1
2
2
0
-
C
l
e
d
o
M
r
ed Wi e System
r
u
si
ibution
str
Ba c Struct
nd RF di
a
for phone
ls
w oUs on
0 -
1 punch do n to
1
nector
e ly
e co
g n s
m
y da a
e o a
Oth r to ls m
8 Bridged 110 connectors...
2
Allows quick installation of phone wiring.
Typical Application
Antenna or CATV
From
Telephone
Company
H E
C A
M e C- 2od
a c S
B si tr r ir m
r o a istr u
fo
Use nly
e
Note position of cutter
Standard 110 tool
NN L IS
0
l
uctu
ne nd RF d
ph
10
o 1 p
ls m y d
too a
r
TM
N
IO
V
2 1
e Syste
ed W
tion
ib
ls
o
n to
ow
d
nc
u h-
n ctor
e c
a
am g on e sOth
Using the 110 connectors
Connect up to 4
TV locations
Connect to 7 phone
locations
Caution: Be sure to use a standard 110 punch tool when connecting CAT5
wire to the 110 connectors. Using make-shift tools such as screwdrivers will
cause the connector to become damaged and make the connection unreliable.
Punch down as many as 4 incoming telephone lines on the input 110 punchdown as shown. Use a 110 punch-down tool to seat and trim all wires.
3
10 Year Limited Warranty
Channel Vision Technology will repair or replace any defect in
material or workmanship which occurs during normal use of this
product with new or rebuilt parts, free of charge in the USA, for ten
years from the date of original purchase. This is a no hassle warranty
with no mail in warranty card needed. This warranty does not cover
damages in shipment, failures caused by other products not supplied
by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only
to the original purchaser, and a purchase receipt, invoice, or other
proof of original purchase date will be required before warranty
repairs are provided.
Mail in service can be obtained during the warranty period by calling
(800) 840-0288 toll free. A Return Authorization number must be
obtained in advance and can be marked on the outside of the shipping
carton.
This warranty gives you specific legal rights and you may have other
rights (which vary from state to state). If a problem with this product
develops during or after the warranty period, please contact Channel
Vision Technology, your dealer or any factory-authorized service
center.
500-136
Loading...