Page 1
A0318
Micro-USB Wall-Dock for CAT5 Audio SystemsBluetooth
• Intelligent Entertainment • Infrastructure • Security Solutions
®
Page 2
Features:
!
!
Charges Micro-USB devices
!
Senses audio to automatically override the main audio source
!
Uses CAT5 cabling
!
Mounts in a standard 2-gang box
!
Bluetooth Streaming
Compatible all Channel Vision CAT5 audio systems
The A0318 is an on-wall Bluetooth Micro-USB docking station for CAT5
audio systems. The non-skid pad helps to hold the music player in place.
The A0318 adds elegant and contemporary styling to make it the perfect
choice for anyone who wants to enjoy their music without defacing the wall.
2
Front/Top
Front/Bottom
Wall Dock
Non-Skid Pad
Secures the iPod
Input RJ-45 & 110 Connectors
Connect to CAT5 Audio Hub
CAT5 cable (only use one)
Output RJ-45 & 110 Connectors
Connect to CAT5 Audio Amplifier Input
CAT5 cable (only use one)
Dock Connector
Connects to iPod
Hinged Dock Lid
Rotates down to
cover the dock
connector
Snap trim
into place
The A0318 is not a standalone device. It must be installed as part of an
audio system which requires the following components:
CAT5 Audio Hub or CAT5 Audio Matrix:
(power supply included)
P-2014
(power supply included)
1 4 CA
T5
Audio Distribution Module
System
System
Input
Local
Input
Zone 1
Zone 2
Local
Priority
Signal
L
R
x
TM
C
H
ANN
E
L
V
I
S
I
ON
Model P-2014
Active
Spkrs
Page 3
3
Installing the Trim Plate Accessory
Install Output
wall plate in j-box
Install Trim plate chassis
over output wall plate
Snap front cover
over chassis
Snap side flange on
to front cover
Snap trim
into place
OR
OR
OR
&
A0125
Volume
Control
Keypad:
Volume
Control
Keypad:
A0127
Volume
Control
Keypad:
A0129
The A0318 is not a standalone device. It must be installed as part of an
audio system which requires the following components:
Other Required Components
CAT5 Audio Hub or CAT5 Audio Matrix:
A0350
(power supply included)
P-2014
(power supply included)
P-2044
(power supply included)
A0240
A0302
In-Room
Amplifier:
Wiring
Interface:
Source
CHA NNE L VI SI ON
Pwr
1 4 CA
T5
Audio Distribution Module
(Required)
Power
(Optional)
Status
System
System
Input
Local
Input
Zone 1
Zone 2
Zone 3
Zone 4
Expansion
Output
Local
Priority
Signal
L
R
Emitters
PRO
C
HAN
N
EL
TM
VI
S
I
ON
IR
x
TM
C
H
A
N
N
EL
V
I
S
ION
Model P-2014
Amp-Link
Channel Vision
R
L/S
Line Out
PRO
CHAN NE L
TM
VISI ON
Active
Active
Active
Active
Link
In
Link
Out
Zone 1
Zone 2
Zone 3
Zone 4
Source 1 Source 2
Source 3
Source 4
Common IR
Source 4 IR
Source 3 IR
Source 2 IRSource 1 IR
IR Data
Power
TM
C
H
ANN
EL
V
I
SIO
N
Model P-2044
Pwr
Mute
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
TM
By CHA NNE L VI SI ON
A r i a
Local In
Active
Spkrs
24VDCIR In
Flush Mount Amplifier
Page 4
4
Using the A0318 as a local source input module
A0318
(Rear)
A0318
(Front)
1 4 CA
T5
Audio Distribution Module
(Required)
Power
(Optional)
Status
System
System
Input
Local
Input
Zone 1
Zone 2
Zone 3
Zone 4
Expansion
Output
Local
Priority
Signal
L
R
Emitters
PRO
CH A
NN EL
TM
V
I
S
IO
N
IR
x
TM
CHA
NN
E
L
V
I
SIO
N
Model P-2014
A0125
P-2014
Tape Monitor or
Room 2 output
(Optional) IR emitters
Sat radio
DVD player
CD player
Receiver
Amp-Link
Channel Vision
R
L/S
Line Out
Source
CH ANN EL V ISI ON
Pwr
Input
Output
System Wiring Diagram
Using the A0318 as a main source input module
A0318
(Rear)
A0318 can be used as primary system inputs feeding the main hub or as
local input modules in each room to override the primary audio source.
Local input modules should be installed in the CAT5 line between the P-
2014 and the A0125. Multiple input modules can be installed in one CAT5
run. If audio is present at more than one input module the unit closest to
A0125 will take priority and be played through the speakers.
In this configuration, either the satellite
radio tuner or the A0318 connected to the
System Input of the P-2014 can act as the
main system input. If audio is present from
both sources, then the Priority switch will
determine which source is heard. In this
example the switch is set to give the A0318
priority.
Primary audio source
Page 5
5
Using the A0318 as a main source input module
A0318
(Rear)
Amp-Link
Channel Vision
R
L/S
Line Out
Amp-Link
Channel Vision
R
L/S
Line Out
Amp-Link
Channel Vision
R
L/S
Line Out
1 4 CAT5 Audio Distribution Module
(Required)
Power
(Optional)
Status
System
System
Input
Local
Input
Zone 1
Zone 2
Zone 3
Zone 4
Expansion
Output
Local
Priority
Signal
L
R
Emitters
PRO
C
H
A
N
N
E
L
T
M
VI S
I
O
N
IR
x
TM
C
H
A
NN
EL V
ISIO
N
Model P-2014
A0318 can be used as primary system inputs feeding the main hub or as
local input modules in each room to override the primary audio source.
Local input modules should be installed in the CAT5 line between the P2014 and the A0125. Multiple input modules can be installed in one CAT5
run. If audio is present at more than one input module the unit closest to
A0125 will take priority and be played through the speakers.
In this configuration, either the satellite
radio tuner or the A0318 connected to the
System Input of the P-2014 can act as the
main system input. If audio is present from
both sources, then the Priority switch will
determine which source is heard. In this
example the switch is set to give the A0318
priority.
Source
CHAN NE L VI SIO N
Pwr
Source
CHAN NE L VI SIO N
Pwr
Room 1 Room 3
A0301A0301
P-2014
A0301
(Rear)
A0125
(Rear)
A0302
OUT
OUT
IN
IN
Secondary audio source
Primary audio source
(See A0125 manual for connection details)
Sat radio
R
L/S
Line Out
R
L/S
Line Out
System Wiring Diagram
Page 6
6
Installing the Wall Dock
Installation Steps
1. Connect all wiring.
2. Attach main chassis to j-box using
the provided four 6-32 screws.
3. Feed the dock connector circuit
board through the opening in the
front cover.
4. Hang the front cover on the main
chassis from the two top tabs.
5. Secure the front cover with the
two small screws at the bottom.
6. Place the dock platform over
the slide rail and push
downward until the retention
snaps are engaged.
7. Slide the side protectors
into the slots on the main
chassis.
Retention
Snap
Slide Rail
2
2
4
3
5
6
6
7
5
2
1
Completed Installation
Steps 3 & 4 complete
Steps 5 & 6 complete
3
In some installations it may be desirable to mount a single gang control
keypad next to the A0318. To accomplish this, the single gang trim plate
can be installed next to the A0318 in a 3-gang junction box.:
Installation Steps:
1. Connect all wiring. Use the correct
installation tools: J-110 tool, or
1014 crimp tool.
2. Install keypad and single-gang
trim plate in the far left position
of the 3-gang junction box.
(See details on page 3)
3. Leave off the right side
flange and trim piece.
4. Install the dock in the
left side of the 3-gang j-box.
It will overlap and snap into
the single gang trim plate.
(See page 5 for details)
Page 7
Installing the Wall Dock
(3-gang Installation)
In some installations it may be desirable to mount a single gang control
keypad next to the A0318. To accomplish this, the single gang trim plate
can be installed next to the A0318 in a 3-gang junction box.:
4
3
Completed Installation
7
Installation Steps:
1. Connect all wiring. Use the correct
installation tools: J-110 tool, or
1014 crimp tool.
2. Install keypad and single-gang
trim plate in the far left position
of the 3-gang junction box.
(See details on page 3)
3. Leave off the right side
flange and trim piece.
4. Install the dock in the
left side of the 3-gang j-box.
It will overlap and snap into
the single gang trim plate.
(See page 5 for details)
See attachment
detail on previous page
Page 8
8
Green/White - Left Channel Audio Ground
Green - Left Channel Audio
Orange/White - Right Channel Audio Ground
Blue - IR Signal
Blue/White - Status
Orange- Right Channel Audio
Brown/White vDC Ground
Brown vDC
Top view:
Pin-out
Stripping and Connecting CAT-5 Wire
Docking
Blade
Cat5
1. Place the CAT-5 between the blade and the first notch of the J-110 tool.
CAT-5 cable should be stripped with a proper stripping tool, such as Channel
Vision’s J-110 tool.
Slight
pressure
Rotate
1 turn only
2. Rotate the tool only once. Multiple turns
will cause you to cut into the inner wires.
3. Inspect the inner wires for damage.
If any wires are cut start over at step 1.
Check for damage
Carefully place the device onto the dock.
Using the A0318 with the A0350 & A0127
The A0350 is compatible with the A0318. Audio from the iPod dock is transmitted
via CAT5 into the A0350 while power is supplied from the A0350 to the iPod
dock.The power supply for the A0350 can be connected directly to the front of the
A0350 or via a pair of 16AWG wires to the power screw terminals on the side.
A0127 or A0129
Pwr
Vid 1
Vid 2
Vid 3
Vid 4
Left
R
+
-
L
+
-
Page 9
Using the A0318 with the A0350 & A0127
9
The A0350 is compatible with the A0318. Audio from the iPod dock is transmitted
via CAT5 into the A0350 while power is supplied from the A0350 to the iPod
dock.The power supply for the A0350 can be connected directly to the front of the
A0350 or via a pair of 16AWG wires to the power screw terminals on the side.
A0127 or A0129
A0350
Pwr
Mute
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
TM
By CHA NNE L VI SIO N
A ri a
Local In
Active
Spkrs
24VDCIR In
Flush Mount Amplifier
Left
Right
Connect power either from
the front or rear (not both)
Connect output
of A0318 here
A0318
(Rear)
A0350
(Side)
A0318
(Front)
Connect keypad here
Input connection
from a CAT5 audio
system is optional.
Connect power via front panel
jack or rear panel screw
terminals.
IR
Keypad
CAT5
Audio
R
+
-
L
+
-
Gnd
24V
Page 10
11
Connection Tips and Troubleshooting
Problem: Not linking with Bluetooth device or Linking with Bluetooth device, but no audio plays.
Troubleshooting:
1. Restart Bluetooth Dock
2. Restart Bluetooth Device
3. Make sure Bluetooth device is in play mode
Warning: Do not adjust the volume all the way up if no audio is present. Doing so could
damage your speakers if audio reconnects.
Problem:
Troubleshooting: Verify you have connected the CAT5 cable correctly. Follow the TIA-568A
standard at both ends. Mis-wiring can cause distorted sound, prevent the system from
functioning, or possibly cause damage to the components in the system. Verify you have
connected the speakers in phase. Follow the label on the product. Out of phase speakers can
rob the system of its bass, especially when driving dual-voice-coil speakers.
If no audio is heard, check to make sure that the audio source is playing, then press the power
button on the keypad to make sure it is turned on.
Audio quality issues
Problem: Hum in System
Troubleshooting: Plug all parts of the system into the same outlet to see if the hum goes away.
Try lifting the ground with a ground lifting plug.
Possible Cause: The different components in the system are connected to different electrical
grounds. This forces electrical currents to find alternate paths to ground causing an audible 60Hz
hum.
Solution: Plug products into an electrical circuit with a common ground.
Additional Tips:
1. The A0318 is designed to charge a Micro-USB device.
The device screen should indicate that it is being charged. If this does not occur, make sure
the power is reaching the volume control keypad (press the volume buttons to see if the LED
indicators light up).
2. Observe wiring distance specifications. The maximum recommended wire length
between the wall dock and CAT5 audio hub is 250 feet. Although the A0318 may work at
greater distances, extreme distances are not recommended because erratic performance
may result due to the power loss caused by the CAT5 wire.
3. If you are experiencing problems with your Micro-USB device that occur even when it is
not docked in the A0318, then please contact the manufacturer of your device.
NOTE: Maximum charging voltage is 5vDC 500mA. Do not plug in a device such as
a tablet computer to this dock. Doing so may cause damage to either device and will
void the warranty.
10
Pairing:
A. Turn Bluetooth on in the pairing device, and scan for Bluetooth devices.
B. To pair with the dock, click on “Android Dock-XXXX” (where XXXX is the last 4
digits of the MAC address) in the Bluetooth device scan list.
C. The pairing device will request a PIN code. The default code is 1234.
D. Enter the PIN code.
E. Your device will pair with the dock.
G. Turn on music to begin streaming.
Disconnecting The Dock:
A. To disconnect the paired dock from your device, disconnect the Bluetooth
connection from the Bluetooth menu of the device.
Connecting The Dock To Another Device:
A. Disconnect the paired dock from your device from the Bluetooth menu of the
device.
B. Turn on Bluetooth on the pairing device, and scan for Bluetooth devices
C. Click on Android Dock-XXXX” (where XXXX is the last 4 digits of the MAC
address) in the Bluetooth device scan list.
D. The pairing device will request a PIN code.
E. Enter the PIN code. The default code is 1234.
F. Pairing success.
G. Turn on music to begin streaming.
Page 11
10
Bluetooth Functionality
Pairing:
A. Turn Bluetooth on in the pairing device, and scan for Bluetooth devices.
B. To pair with the dock, click on “Android Dock-XXXX” (where XXXX is the last 4
digits of the MAC address) in the Bluetooth device scan list.
C. The pairing device will request a PIN code. The default code is 1234.
D. Enter the PIN code.
E. Your device will pair with the dock.
G. Turn on music to begin streaming.
Disconnecting The Dock:
A. To disconnect the paired dock from your device, disconnect the Bluetooth
connection from the Bluetooth menu of the device.
Connecting The Dock To Another Device:
A. Disconnect the paired dock from your device from the Bluetooth menu of the
device.
B. Turn on Bluetooth on the pairing device, and scan for Bluetooth devices
C. Click on Android Dock-XXXX” (where XXXX is the last 4 digits of the MAC
address) in the Bluetooth device scan list.
D. The pairing device will request a PIN code.
E. Enter the PIN code. The default code is 1234.
F. Pairing success.
G. Turn on music to begin streaming.
Page 12
Channel Vision Technology will repair or replace any defect in material or workmanship
which occurs during normal use of this product with new or rebuilt parts, free of charge in
the USA, for one year from the date of original purchase. This is a no hassle warranty with no
mail in warranty card needed. This warranty does not cover damages in shipment, failures
caused by other products not supplied by Channel Vision Technology, acts of God, or
failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is
extended only to the original purchaser when purchased through an authorized reseller, and
a purchase receipt, invoice, or other proof of original purchase date will be required before
warranty repairs are provided. Mail in service can be obtained during the warranty period by
calling (714) 424-6500. A Return Authorization number must be obtained in advance and
can be marked on the outside of the shipping carton. This warranty gives you specific legal
rights and you may have other rights (which vary from state to state). If a problem with this
product develops during or after the warranty period, please contact Channel Vision
Technology, your dealer or any factory-authorized service center.
Channel Vision products are not intended for use in medical, lifesaving, life sustaining or
critical environment applications. Channel Vision customers using or selling Channel
Vision products for use in such applications do so at their own risk and agree to fully
indemnify Channel Vision for any damages resulting from such improper use or sale.
Specifications: (typical @25º C)
Cable Requirements: CAT-5 or better
Operating Temperature: -10ºC to +50ºC
Specifications subject to change without notice.
1
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
Tested To Comply
With FCC Standards
500-382 Rev B
234 Fischer Avenue, Costa Mesa, California 92626 USA
(714)424-6500 (800)840-0288 (714)424-6510 fax
email: techsupport@channelvision.com
• Intelligent Entertainment • Infrastructure • Security Solutions
ww w. ch ann el vi si on .c o m
Loading...