A0127 ... Keypad controller for use with the A4601.
Features:
Available in both white (A0127W) and ivory/almond (A0127IA) colors.
Teaching capability allows controls to be stored in learning remote controls.
User changeable source buttons make it easy to customize.
Source selection buttons
allow any of the 4 sources
to be selected for playback.
Power button.
Turns off the audio and
video playing in a zone.
How IR repeating works
Point any
IR remote control
at the A0127
Rew<<
Learn
Play>
1
Stop
4
7
Power
2
Pause
5
8
3
0
6
Ch
Select
9
-/-T
uner
VCR
V
ol
Learn
Channel V
CD
Error
All Off
DVD
Off
AB-500
Sat
ision
TV
TM
Volume +/- buttons.
Increases or decreases
Vid 1
Vid 2
Vid 3
Vid 4
Vol
+
Vol
-
the audio level in a zone.
Mute button.
Mutes the audio playing
Pwr
Mute
in a zone (video will still
be present).
IR receiver.
Detects IR signals and repeats
through the IR system.
The Pwr button
Vid 1
Vol
Vid 2
+
Vid 3
Vol
-
Vid 4
Pwr
Mute
Tx
Batt
FF>>
flashes as IR
information is
received.
And the flasher
repeats the IR signal
in the other room.
CD player
Be sure the flasher is attached
directly over the component’s IR
2
receiver.
Changing buttons face plates on the A0127 keypad...
The A0127IA comes with both Almond and Ivory face plates and buttons.
Both the A0127W and A0127IA come with replacement buttons labeled for a
variety of sources.
Faceplate tabs
The procedure below describes the
how to exchange your buttons and
faceplate.
Vid 1
Vol
Vid 2
+
Vid 3
Vol
-
Vid 4
Pwr
Mute
Tuner
Sat
CD
Zone
CD 2
XM
Cam 1
Cam 2
Cam 3
TV
DVD
Sirius
1 Detach the existing faceplate by
pressing the plastic tabs with a flat
blade screwdriver. (Press inward and
upward at a 30 degree angle)
1
Buttons
Align rubber tabs
with
holes in PCB
Accessories
Power
Tuner
VCR
Channel Vision
AB-500
DVD TV
CD Sat
TM
Learn
All Off
OffSelect
Error
Learn
Rew<< Play> FF>>
4
7
1 2
Ch
5
8 9
0
-/--
Vol
6
3
AB-500 ... Universal remote control.. Learns IR
Tx Batt
Stop
Pause
codes for up to 6 sources.
IR-3003 & IR-3002 ... Single and dual head IR
flashers. Use one head per source to control
from the remote room. (IR-3002 shown).
Cam 4
30
2 Exchange the labeled buttons
(and colored faceplate) to your
preference and assemble as
shown
°
1
3
Channel Vision A4601
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
See page 6 for
connection details
A4603 Rear Panel
Control
6
5
R-Audio-LVideoR-Audio-LVideoR-Audio-LVideo
4
Control
3
5
46
OUTPUTSOUTPUTS
GLOBAL
INPUT
4
CHANNELS
21
R OUT
R IN
LIN
R IN
LOCAL
L IN
L OUT
GLOBAL
R OUT
R IN
LOCAL
L IN
L OUT
GLOBAL
R OUT
R IN
LOCAL
L IN
L OUT
GLOBAL
R OUT
R IN
LOCAL
L IN
L OUT
GLOBAL
R OUT
R IN
LOCAL
L IN
L OUT
GLOBAL
6345
ROUT
R IN
LOCAL
L IN
LOUT
GLOBAL
A1260 Rear Panel
Vid 1
Vol
Vid 2
+
Vid 3
Vol
-
Vid 4
Pwr
Mute
Room 6
Rew<<
Learn
Tx
Batt
1
Play>
Stop
4
FF>>
2
Pause
5
8
3
6
9
-/--
7
Power
0
Ch
Select
T
uner
VCR
V
ol
Learn
Channel Vision
CD
All Off
DVD
Error
AB-500
Off
Sat
TV
TM
Sat radio
DVD player
CD player
2
R OUT
L OUT
Control
1
Video In
Termination
Hi-Z
75
13
2
1 23 4
Sig
Gnd
+V
IR Emitters
R-Audio-LVideo
R-Audio-LVideo
3
4
1A/250V
FUSE
Input Voltage
1
2
INPUTSOUTPUTS
ŸIR emitter outputs allow IR-3002 flashers to be connected for
remote control of source components.
ŸEach zone is controlled through the A0127 keypad which
connects to the RJ45 jacks on the rear panel.
ŸA learning remote (such as the AB-500) can be programmed
to control your source components and the A0127 (see
page 7 for details). This is an easy way to control all your
components from any room in the house.
Power
115
230 / 115 VAC
50 / 60 Hz
Note: If you are using a Philips Pronto remote control, you may
download IR codes for the A0127 from www.channelvision.com
or from www.remotecentral.com.
5
Wiring the A0127 keypad...
Keypads connect to the A4601 through the RJ45 jacks on the back panel of
the A4601. Connections to the A0127 may be accomplished either by using
the RJ45 jack or the screw terminals provided on the back side of the keypad.
When using the RJ45 jacks, simply wire both ends of the cable according to
the TIA568A standard. When using the screw terminals on the A0127, make
sure to wire the RJ45 plug connecting to the A4601 as shown below.
Front
Vid 1
Vid 2
Vid 3
Vid 4
Pwr
Vol
Vol
Mute
+
-
A0127
Rear
Pin 8: +VDC
Pin 7: Ground
Pin 4: IR signal
Pin 4: IR signal
Pin 7: Ground
A4601
Pin 8: +VDC
Pin 4: IR signal
N.C.
Pin 7: Ground
Pin 8: +VDC
6
Stripping and Connecting CAT5 Wire
CAT5 cable should be stripped with a proper stripping tool, such as Channel
Vision’s J-110 tool.
1. Place the CAT5 between the blade and the first notch of the J-110 tool.
CAT5
Blade
2. Rotate the tool only once. Multiple
turns could damage the inner wires.
3. Inspect the inner wires for damage.
If any wires are cut start over at step 1.
Check for damage
TIA-568A RJ-45 Modular Plug
Side view:
Rotate
1 turn only
Slight
pressure
Top view:
Green/White - Left channel ground
Green - Left channel
Orange/White - Right channel ground
Blue - Signal
Blue/White - Status
Orange - Right channel
Brown/White - Ground
Brown - 24vDC
7
Using the A0505 remote control..
designed to control your A4603.
(Download IR codes at: www.channelvision.com and www.remotecentral.com)
Zone Power - Turns on/off the zone you are in
Power - Master power
CH AN NEL V ISI ON
MODEL
A0505
ZONE
POWER
CAMERA
CATV
MOD
VOL
POWER
1
3
MUTE
1
S
O
2
U
R
C
3
E
4
2
4
(turns all zones on/off)
Source Buttons
Vid 1
Vid 2
Vid 3
Vid 4
Pwr
Vol
Vol
Mute
+
-
Mute - Mutes the audio
for the zone you are in
N
O
I
S
1
EL VI
POWER
N
HAN
2
C
S
O
U
3
R
C
MODEL
E
A0505
4
2
1
4
3
VOL - Controls volume
for the zone you are in
CAMERA
ZONE
POWER
MUTE
TV
CA
VOL
MOD
Setting the A0127 as the master keypad...
By changing a jumper setting on the A0127 you can make it a master keypad.
This simply means that the master A0127 will be able to power on or power off
the entire system from a single zone.
Normal control
jumper position
Master control
jumper position
Power button will
now turn off/on all
zones
When the system
is powered back on
each zone will return
to its previous volume
level and source
selection.
Vid 1
Vid 2
Vid 3
Vid 4
Pwr
Vol
Vol
Mute
+
-
8
1
Channel Vision Technology will repair or replace any defect in
material or workmanship which occurs during normal use of this
product with new or rebuilt parts, free of charge in the USA, for one
year from the date of original purchase. This is a no hassle warranty
with no mail in warranty card needed. This warranty does not cover
damages in shipment, failures caused by other products not supplied
by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only
to the original purchaser, and a purchase receipt, invoice, or other
proof of original purchase date will be required before warranty
repairs are provided.
Mail in service can be obtained during the warranty period by calling
(714) 424-6500. A Return Authorization number must be obtained
in advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other
rights (which vary from state to state). If a problem with this product
develops during or after the warranty period, please contact Channel
Vision Technology, your dealer or any factory-authorized service
center.
Channel Vision products are not intended for use in medical,
lifesaving, life sustaining or critical environment applications.
Channel Vision customers using or selling Channel Vision products
for use in such applications do so at their own risk and agree to fully
indemnify Channel Vision for any damages resulting from such
improper use or sale.
500-071 revD
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.