How it Works
Channel Vision
Loading...
6522
Instructions Manual
43 pgs4.84 Mb0
User Manual
43 pgs4.76 Mb0

Channel Vision 6522, 6521 User Manual

Download
6521
Dome Color Megapixel IP Camera w/IR Illuminators
6522
Bullet Color Megapixel IP Camera w/IR Illuminators
Table Of Contents
2
Models 6521/6522
The 6521 & 6522 are 2 Megapixel bullet and dome CMOS IP cameras.
Built-in web server, allows users to view high quality, real-time video with the Internet Explorer browser.
•
•
Uses H.264, MJPEG and MPEG4 codecs
•
Live video can be recorded to a computer and played back remotely, as well as viewed from many mobile phones and other devices.
Designed for large commercial projects with 100’s of cameras or a single family house requiring a
•
camera at the front door.
6521 Features:
Channel Vision’s 6521 Vandal Proof IP Dome offers superior image quality with a 2 megapixel CMOS sensor and has the ability to capture images up to UXVGA (1600 x 1200 pixels). With H.264 compression, less bandwidth and storage space are used, while delivering full resolution at max frame rate with faster speeds over the internet. The 6521 also features event triggered SD card recording, as well as 18 IR LED for a viewing distance of 50 feet in total darkness. Monitoring can be done anywhere an internet connection is available even from a 3G Smart-phone
6522 Features:
Channel Vision’s 6521 Vandal Proof IP Dome offers superior image quality with a 2 megapixel CMOS sensor and has the ability to capture images up to UXVGA (1600 x 1200 pixels). With H.264 compression, less bandwidth and storage space are used, while delivering full resolution at max frame rate with faster speeds over the internet. The 6522 has a varifocal lens with built-in 35 IR LED for a viewing distance of 60 feet in total darkness Monitoring can be done anywhere an internet connection is available even from a 3G Smart-phone
6521
6522
3
Warnings
WARNINGS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION：TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
COPYRIGHT
ALL TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED TO THEIR RESPECTIVE COMPANIES.
4
Cable Pin Out
DC 12V (Optio if not
DC 12V (Optio if not
g oE switch
n P
usi
n
n
g oE switch
n P
usi
Rev
Rev
R v 2e
R v 2e
1
1
erminal
erminal
O I/T
O I/T
p
ut
ou
ou
op
r ho
op
r ho
ho Microp
(Opti
V o i n sDC 12
(Opti
V o i n sDC 12
ermi
ermi
T nalI
T nalI
pho e In
pho e In
t
t
ne
ne
ne
ne
n
n
pV
ut
pu
I
pu
n
I
n
Output
Output ho Microp
n f
n f
p
ut o
p
ut o
ideo
ideo
V
Ethernet Port
Ethernet Port
5
(T 68B Standard)
5
(T 68B Standard)
/O
/O
Vi eo outputd
Vi eo outputd
Micr
Micr
tMic
tMic
ot u ing PoE switch
ot u ing PoE switch
ALARM IN
RELAY OUT
GND Alarm N.C. Common Ground N.O.
o n Ou p
o n Ou p
Mi r pho
Mi r pho
5
5
WARNING DO NOT CUT THE BREAKOUT CABLE. CUTTING THE CABLE WILL VOID THE WARRANTY ON THE DEVICE. Channel Vision will still provide technical support if the cable is cut, but cannot guarantee functionality.
The breakout cable on Channel Vision’s IP Cameras are used for motion detection, event triggering, alarm notifications etc. The provided interface connections are explained below.
1.) Digital Input (GND+Alarm):
An alarm input for connecting devices that can toggle between an open and closed circuit, for example PIRs, door/window contacts, broken glass detectors, etc. When a signal is received, the state changes and the input becomes active.
2.) Relay output (COM +N.O.) / (COM+N.C.)
A selectable output for a relay switch, for example LEDs, Sirens, etc. Normally Open and Normally Closed can be selected via the Internet Explorer ActiveX control under the “I/O Setting” section on the left. (See pages 35, 36 for I/O settings)
e t utc
e t utc
etEthern Connector
etEthern Connector
)
d(T 68B Standar
)
d(T 68B Standar
5
PoE (Power Over Ethernet)
Power over Ethernet (PoE) is a technology that integrates power into a standard LAN infrastructure. It enables power to be provided to the network device, such as an IP phone or a network camera, using the same cable that is used for the network connection. The PoE switch eliminates the need for power outlets at the camera locations and enables an easier application of uninterruptible power supplies (UPS) to ensure 24 hours a day, 7 days a week operation.
A 802.3af, 15.4W PoE Switch is recommended with 6521 and 6522. If using a PoE switch that does not meet this specification, full functionality may not be supported.
6522
Ethernet Cable
E
thernet
Ca
6521
bl
e
PoE Ethernet Switch
(Not sold by Channel Vision)
o
w
er Sup
pl
y PoE P
of
Switch
6
Assigning an IP Address
1.) Use the software, “IP Installer” to assign the IP address to your 6521 or 6522. You can find
"IP Installer" in the supplied CD.
2.) Execute IP Installer. This is located on your disk under the folder “Megapixel Camera Network Search Application”
3.) If Windows prompts you to unblock IP Installer, you must select “unblock”
There are 3 kinds of IP configuration
A.) Fixed IP (Public IP or Virtual IP) B.) DHCP (Dynamic IP) C.) Dial-up (PPPoE)
"IP Installer" will search all IP Cameras connected to your LAN network.The user can click “Search Device” to search again.
7
Assigning an IP Address /cont
1.) Click the start icon on your computer
2.) Click the ‘Run’ icon on your computer.
3.) Type in ‘cmd’ and press enter on your keyboard, or press ok.
4.) Type in ‘ipconfig /all’ into the DOS prompt that appears. Press enter.
5.) Write down your computer’s IP address.
It is important that we do not use the same IP address for our IP Camera. In the example below, the computer’s IP address is 192.168.1.74. The IP address of the IP Camera must be different than the IP address in the computer. Each networkable device in your network has an IP address assigned. You need to be sure the IP you choose for your IP camera is not the same as any other device on your network.
8
Assigning an IP Address /cont
6.) Copy/write down the following information from the DOS prompt.
A.) Default Gateway (Example 192.168.1.1) B.) DNS Server (if 2 servers, use the first one, for example 192.168.1.9) C.) Subnet Mask (Example 255.255.255.0)
9
Assigning an IP Address /cont
7.) Enter the information you wrote down from step 6 on page 9 into the IP camera network page
A.) Default Gateway (Enter this number under “Gateway”) B.) DNS Server (Enter this number under “DNS 1”) C.) Subnet Mask (Enter this number under “Netmask”)
8.) Giving the IP Camera a unique IP address.
Assign and IP address to the IP Camera by using the first 3 sets of numbers of your default gateway. A IP address, has 4 sets of numbers, each followed by a period. For example, xxx.xxx.xxx.xxx My default gateway is 192.168.1.1 So, for example, my IP Camera’s address will start with 192.168.1.xxx
9.) Make sure you use a number different that your computer’s IP address. (Generally between 2-250) This number needs to be out of the range of DHCP. DHCP is assigned with your router, and can be checked by logging into the router.
My computer’s IP address is 192.168.1.74. I have used 192.168.1.208 for my IP Camera. You must choose a number that is different from your computer’s IP. If your IT technician has designated a static internal IP for your IP Camera, use that address.
10.) To assign the port, choose a port between 5400-9000, and type it into “Port 1” If a specific port has been designated for your security system, that can also be used, even if the number is not within the range of 5400-9000.
First 3 numbers are same as computer
Select “Static”
Name
Fourth number (different than computer)
Subnet Mask (same as computer)
Default Gateway (same as computer)
DNS Server 1 (same as computer)
DNS Server 2 (same as computer)
Port (A port between 8000-8999 is recommended, but any network port can be used)
To change numbers, select the appropriate area on IP installer with your mouse, and type in the info.
*Disclaimer: This is an example based on a general network setup. All networks do not match these settings exactly, as all networks are different
10
Connecting To Your Camera
1.) Open Internet Explorer. Type the IP address of the IP camera into the browser link window.
Also, make sure to type the port at the end of the link.
For example, I will type in http://192.168.1.207:8005
2.) You will be prompted for a username and password. The default username is ‘admin’ The default password is ‘admin’
Installing The ActiveX Control
1.) The first time you connect to the camera via Internet Explorer, it will ask you to install the ActiveX control. Internet Explorer 6, 7, 8, or 9 must be used to run this ActiveX control.
11
Configuring Internet Explorer
If the installation of the ActiveX control fails, for example the browser page says “done” but you do not see your camera, please check the security settings for your IE browser. Follow the instructions below.
Step 1
Step 3
Step 2
Step 4
12
When popup the following dialogue box, click “Yes”.
Step 5
Live Viewing
Once you connect to your camera, you will see the following screen. Below the icons and their functionality is described.
Snapshot
Settings
13
Controls the selection of the video stream that is being viewed
Activates 2-way audio
Controls the physical size of the streaming video on the browser screen
Format: Year/Month/Day/Hour/Minute/Second/ Image Size/Frames Per Second
Shows the number of users connected at any given time
Activates relay output
Live Viewing/cont.
1.) This icon opens the settings’ menu
2.) This icon takes a snapshot
3.) This icon show system time, video resolution, and video refreshing rate
4.) The bottom bar has an icon that allows you to select which stream
you want to view. Stream 1 is usually the larger, better quality stream. Stream 2 is the smaller stream, generally used for mobile viewing
5.) These cameras support 2 way audio. The bottom bar has an icon will activate 2 way audio For 2 way audio to function, you need a microphone plugged into the computer.
6.) The bottom bar has an icon shows how many users are connected to the IP camera.
7.) This icon will control/activate the relay output on the camera wire pigtail. A relay can activate lights, alarms, or anything that uses a contact closure.
8.) If you double click the video feed, it will make the video full screen. To change video back to normal mode, press ‘Escape’ on your keyboard, or double click anywhere in the video feed a second time.
9.) If you right click on the video, you have access to several different functions.
A.) Snapshot: Takes a snapshot B.) Record Start : Records video to your computer
C.) Mute: Mutes 2 way audio, if activated D.) Full Screen: Makes the IP camera full screen
E.) Zoom: Digital zoom. This is explained below
Digital zoom
1.) Select “Enable digital zoom”
2.) Select the area of the screen you wish to zoom in on
3.) Select the zoom level
2
1
14
3
Configuration
1.) Select this icon to enter the settings menu
1
2.) Select this icon to go back to your live video feed
2
15
System Configuration
System Information:
Use the number scheme below for a description of each item:
1.) MAC Address: (Media Access Control) address; This is a unique identifier assigned to IP devices for communication with the network. Your IP camera is pre-set with a MAC address
2.) Server name: Select to edit the camera name
3.) LED Indicator: Select On/Off to toggle the blinking LED light in the camera
4.) Language: Select a language to change the language of the ActiveX interface
5.) Status Bar: Select On/Off to toggle the information bar (below the main video stream)
6.) Time Stamp: Select Enabled/Disabled to turn the video timestamp on or off
7.) Text: Select Enabled/Disabled to specify the name that can be displayed on the top left area of the screen
8.) Server Time: This shows the current time on your IP camera
9.) Date Format: Select to choose your desired date format
10.) Time Zone: This shows your current time zone
11.) NTP: The Network Time Protocol is a protocol for synchronizing the clocks of computer systems
12.) NTP Server: If you have a NTP server, input it here
13.) Update: If using an NTP server, select this drop down menu to choose the update interval
14.) Time Shift: Time shift is used to compensate for the time it takes to server to process the sync request for your time. This is usually not needed.
15.) Synchronize with PC’s time: Select this to match your computer’s clock to your IP camera
16.) Apply: Select this button to save your changes
1
2 3
4
6
7
8
9 10 11
12
13
14
5
16
15
16
User Management
User managment:
This IP camera supports 3 different types of users.
1.) Administrator
2.) General
3.) Anonymous
Click “Yes” to allow anonymous user access Click “Add/Set” to add a user Click “Edit” to modify a user. When you click edit, the following window will pop up: (Shown below.)
Add the username and password, and click “OK” to save your new user.
17
System Update
System Update: This menu is used to perform the following functions:
1.) Firmware Update: Channel Vision will update the firmware from time to time.
By registering your IP camera, you have access to all firmware improvements and extended warranty options. How? See our warranty page for more information. Below is a link to the warranty page. Http://www.channelvision.com/index.php/Table/PRODUCT-WARRANTY/ To load new firmware, press “Browse” and select the firmware.bin file.
18
2.) Restart System: Select to restart system. You can reset the IP camera to factory default settings if desired If you backup your settings, you can load your backup file where it says “New Setting File”
3.) Settings backup:
You can backup your settings by right clicking your mouse on “Setting Download” and selecting “Save Target As”. You may also load previously saved settings files this way. When loading previously saved files, click “Browse” and then “Upgrade”
Network
Network Setup/IP Setting: This setting is for the external viewing of camera over the internet.
Once set up, you will be able to view this camera from anywhere in the world. This IP camera supports DHCP and Static settings. If you are new to installing an IP camera, use #2 (Static IP)
1.) DHCP: If you use this setting, your IP information will be pulled automatically from your router. This not recommended if you are going to view this camera outside of the building that it resides in.
2.) Static IP: This is an IP that you manually set. This IP must not be the same as any other device within your network. You must also set default gateway, DNS server, subnet mask, and DNS server. Please refer to page 6 & 7 for instructions on how to obtain these numbers.
3.) Port Assignment: You can assign different ports for your camera. (Explained below.)
A.) Web Page Port: (This is the port that 99% of installations will use) A web page port is used to transmit data out of your network. For example, If my external IP address is http://67.88.12.50, and my port was 5400, I would put a “:” and the port. The final address would be http://67.88.12.50:5400
For information on network ports, please refer to the link below:
http://en.wikipedia.org/wiki/Network_ports
B.) RTSP Transmitting Port: For information on RTSP, please refer to the link below.:
http://en.wikipedia.org/wiki/Real_Time_Streaming_Protocol
C.) RTP start and end port: In RTSP mode, you may use TCP and UDP for connecting TCP connection uses RTSP port (554) UDP connection uses RTP start & end port.
4.) UPnP: This IP camera supports UPnP. If this service is enabled on your computer,
the camera will be automatically detected and a new icon will be added to “My Network Places”. For information on UPnP, please refer to the link below:
http://en.wikipedia.org/wiki/UPNP
Below are instructions on how to activate UPnP on your computer:
A.) Open the control panel from the start menu. B.) Select “Add/Remove programs” C.) Select “Add/Remove Windows components” D.) Open “Networking Services” section E.) Click “Details” and select UPnP to setup the service. F.) Once activated, the IP camera icon will appear in “My Network Places” G.) You can now double click that icon to access the camera with your IE browser.
19
Network/cont
Network/cont: Below is an example of the network settings menu. This is where you key in all of your IP
information from your network. These settings must be entered correctly in order for the IP camera to be viewable over the network.
20
5.) PPPoE: Check the PPPoE “Enabled” button to activate this function.
You can key in a username and password for the connection if you are using ADSL.
Send mail after dialed: When connected to the internet, this IP camera will send a
email to the specified email account. To configure the IP camera email settings,
please refer to the “Mail and FTP Settings”
Network/cont
Network/cont: DDNS:
This IP camera supports DDNS (Dynamic DNS) service. Select “Enabled” to enable the DDNS service.
For viewing the cameras over the internet while using a dynamic (rotating) IP address, there are many services available online. For more details, please review the "instruction manual" tab on the product info page located at www.channelvision.com and click on the “DDNS basic instructions PDF file.
21
1.) Enable the service
2.) Key in the DynDNS server name, username, and password
3.) Set up the IP update refresh rate
4.) Click “Apply”
5.) If it updates to often, the IP will be blocked by DynDNS Channel Vision recommends you set it to update once per day (1,440 minutes)
Network/cont
Mail & FTP: Enter your Mail and FTP information into the menu below:
Mail: Mail is a way the IP camera can send you an email when certain actions occur, for
example motion, a contact closure on the sensor, etc. For more details, please see page 32
FTP: FTP is for uploading recorded files to a designated FTP site
22
Please note: standard servers block devices such like this, due to spam settings. You may not be able to use the following free services:
Live.com Hotmail.com Yahoo.com Gmail.com Mail.com Apple.com MSN.com
Video Settings
Image Setting: You can adjust the following items on this camera:
1.) Brightness: This adjusts the brightness level of the camera
2.) Contrast: This adjusts the difference in color and light between parts of an image
3.) Sharpness: This adjusts how sharp the image appears
4. ) AGC: This adjusts the automatic gain control
5.) BLC: This turns off or on the back light compensation for the video
6.) AWB R-Gain: This adjusts the auto white balance right
7.) AWB B-Gain: This adjusts the auto white balance left
8.) Night Mode: This adjusts the frame rate during low light recording or viewing
9.) Video Orientation: This will allow you to flip or mirror the video stream
23
1 2
3 4
5 6
7 8
9
You can reset your IP camera’s image settings to default by pressing the “default” button
Video Settings/cont.
The 6521 and 6522 IP cameras are varifocal. This means you can adjust the zoom and focus level of the camera from 2.7-9mm on the 6521 and
3.6-16mm on the 6522
How to adjust zoom and focus on the 6522
Focus
Zoom
24
1.) Using a flat head screwdriver, adjust the zoom or focus screws on the 6522 camera To adjust the zoom and focus, the Channel Vision 15-AU25MM portable test monitor is reccomended
15-AU25MM
Video Settings/cont.
To adjust zoom and focus on the 6521, first, you have to take off the plastic dome piece. To do this, unscrew the 5 vandal resistant screws using the tool that comes with the 6521.
6521
How to adjust zoom and focus on the 6521
2
2
Focus
Zoom
25
1.) You will need to unscrew each of the knobs slightly (counter-clockwise) with your fingers or a flat head screwdriver. If you do not unscrew the knobs first, you will be unable to move them
2.) Once you have loosened the zoom or focus knob, use the knob as a lever to turn the circular lens piece
3.) Once you are done adjusting your zoom and focus, screw the knobs back in (clockwise)
Video Settings/cont.
Video Setting:
Click the drop down list to select Input Resolution, Video System and TV Output
Streaming: Basic mode:
1.) Resolution:
There are 8 resolutions you can choose from.
1600x 1200, 1280x1024, 1280x960, 1280x720, 800x600, 640x480, 320x240,
& 176x144
2.) Quality:
There are 5 levels you can adjust to: Best, High, Standard, Medium, & Low. If you use the highest settings, the network streaming speed will be slower Also, if you record any files, the higher the quality, the larger the file will be
3.) Video Frame ate: The video refresh rate per second Setting max is 30 FPS (NTSC) and 25 FPS (Pal) at 1280x720 and best quality
Video Format: This describes the codec use for compression. H.264 is newer
4.)
and higher quality, and MJPEG (JPEG) is an older, but may stream faster
5.) RTSP Path: RTSP output name. For example, if I choose camera, the rtsp path would be as follows: rtsp://camera/ (For more information on RTSP, follow the link on page 19)
R
26
Video Settings/cont.
Streaming (Advanced Mode):
1.) Resolution:
There are 8 resolutions you can choose from.
(UXGA)
2.) Bitrate Control mode:
There are 2 choices. CBR (Constant Bit Rate) and VBR (Variable Bit Rate)
A.) CBR: 32Kbps-4Mbps (The higher the CBR, the better your video quality will be) B.) VBR: 1 (Low) -10 (High) Compression rate. The higher the compression rate the higher the picture quality, and vi e versa. The balance between VBR and network bandwidth will affect your picture quality. When using VBR, it is less likely that your streaming video will break up or lag.
3.) Video Frame Rate: The video refreshing rate per second NTSC: Max 30 frames per second PAL: Max 25 Frames per second
4.) GOP Size: This means ‘Group of Pictures.” The higher the GOP is, the better the quality of the images
5.) Video Format: This describes the codec use for compression. H.264 is newer and higher quality, and MJPEG (JPEG) is older, but will stream faster
1600x 1200 1280x1024 (SXGA) 1280x960 (SXGA-) 1280x720 800x600, 640x480 3 (qVGA)
20x240
176x144 (qCIF)
(WXGA)
(VGA)
c
27
6.) RTSP Path: RTSP output connecting route For example, rtsp://camera/ (For more information on RTSP, follow the link on page 19)
Video Settings/cont.
Stream ( Mode):
1.) Resolution:
There are 8 resolutions you can choose from.
(UXGA)
2.) Quality:
There are 5 levels you can adjust to: Best, High, Standard, Medium, & Low If you use the highest settings, the network streaming speed will be slower Also, if you record any files, the higher the quality, the larger the file will be
2 Basic
1600x 1200 1280x1024 (SXGA) 1280x960 (SXGA-) 1280x720 800x600, 640x480 3 (qVGA)
20x240
176x144 (qCIF)
(WXGA)
(VGA)
28
3. Video Frame Rate: The video refreshing rate per second
4.) Video Format:
and higher quality, and MJPEG (JPEG) is older, but may stream faster
5
.) RTSP Path: RTSP output connecting route
For example, rtsp://camera/ (For more information on RTSP, follow the link on page 19)
This describes the codec use for compression. H.264 is newer
Video Settings/cont
Stream Mode:
1.) Resolution:
There are 8 resolutions you can choose from.
& 176x144
2.) Bitrate Control mode:
There are 2 choices. CBR (Constant Bit Rate) and VBR (Variable Bit Rate)
2 Advanced
1600x 1200, 1280x1024, 1280x960, 1280x720, 800x600, 640x480, 320x240,
3.) Video Frame Rate: The video refreshing rate per second.
4.) GOP Size: This means ‘Group of Pictures.” The higher the GOP is, the better
the quality of the images.
.) Video Format:
5 This describes the codec use for compression. H.264 is newer
and higher quality, and MJPEG (JPEG) is older, but may stream faster.
6.) RTSP Path: RTSP output connecting route. (For more information on RTSP, follow the link on page 19)
3GPP Streaming Mode:
1.) Enable or Disable 3GPP Streaming
2.) 3GPP: 3GPP output name
*Channel Vision recommends you use 176x144 resolution, 5FPS, MPEG4 format for 3GPP mode
29
Recommended Video Settings
Below are a few examples of recommended settings, depending on the situation.
1.) Viewing a stationary object, or area that does not receive much movement
If the camera is looking at a stationary object, or an area that does not receive a lot of traffic or
movement, the camera can be set to the highest settings. An example of the highest settings are below:
2.) Viewing an area that receives a lot of traffic or movement
If the camera is looking at an area that views constant or near constant movement, a medium setting
is recommended. An example of medium settings are below:
30
Recommended Video Settings/cont
3.) Viewing a 6521 or 6522 on a slow internet connection If the 6521 or 6522 is installed on a network that does not have a very fast internet connection,
or you are viewing on a network with limited bandwidth, the example below is recommended.
4.) Viewing a 6521 or 6522 on the lowest settings Below is an example of the lowest settings on the 6521 and 6522 IP cameras
31
Audio
Audio:
Channel Vision IP Cameras support 2-way audio, allowing you to listen with an external microphone and speak through powered speakers using your PC, both internally in your network, as well as remotely over the internet. You can send audio from the IP camera to the PC you are connected to. You can also send audio from the PC to the IP camera. This audio output on the camera is located on the camera pigtail. You would need to connect to an amplifier, for example the A0240. To send audio from the PC to the IP camera, you need a standard microphone plugged into the computer, for example a 5104-MIC. You can also plug a microphone directly into the 6521, to feed the A0240 directly.
A0240
(Amplifier)
6521
32
Speaker Wire
5104-MIC
VC-302
(Volume Control)
Audio/cont
Audio: Below are instructions on how to enable audio on your IP camera.
Select “Ena led” to activate audio from e cam to your PC
b th era
33
Select “Chatting” to activate audio from your PC to the audio output of your IP camera
While recording to an SD card on the IP camera, audio playback will be choppy.
*
Event List
34
1.) Event Setting: The purpose of this menu is to configure what the camera will do when an “event” is generated.
2.) Motion Detection
The 6521 & 6522 allow 3 areas of motion detection. (Area Setting) When motion is triggered, they can send the video, in the form of events to a specific mail address, transmit the live video to a remote FTP server, trigger a relay, and save events in the form of video to local SD card. (SD Card recording only available with the 6521 dome camera) To set up the motion area, click “Area Setting”. Use the mouse to click and drag a box of the area you want to select.The same method is used for area 2 and area 3.
.3.) Record File Setting: The 6521 & 6522 allow 3 different types of recording files. A.) AVI File (With time stamp) This is the largest file size option to choose, but the video will
be the highest quality available. B.) JPEG (MJPEG) File (With time stamp) This is a smaller file size to choose, but is of lower quality than the AVI format.
C.) JPEG (MJPEG) Single file with interval setting.
Event List/cont.
35
4.) Record Time Setting: Pre Alarm and Post Alarm setups for record start and end time when motion is detected, or to trigger a relay. Note: Pre/Post Alarm record time based on record time setting and 6521 or 6522's built-in memory. The ability to store data is limited, so if the video quality is set very high, this will cause a drop in the recorded FPS. This will also decrease pre or post recording time.
5.) Network IP Check: This option does two things. One, it checks your internet connection (Interval) to make sure your network connection has not been lost. Two, if your connection is lost, you can set this to automatically record to the SD card until it is full.
“IP Check” enables or disables this feature. “IP Address” is what the camera will use to check if the internet is still working. “Interval” is how often the camera will test your internet connection. “IP Check” (lower option) has a box to check. When you check this box, you will record to your SD card
upon network failure.
Schedule
1.) Schedule: Complete schedule setup to tell the 6521 or 6522 when to record data.
2.) Snapshot: After enabling the snapshot function, user can select the storage
location of the snapshot, the time of snapshot, and the file name of snapshot.
Click “Enabled” to enable snapshot. Select the E-mail, FTP, or Save to SD card option to enable.
Click the desired areas (boxes) to designate recording time. Green=record
36
I/O Setting
I/O Setting:
The 6521 & 6522 supports 1 input/1 output. When the input is triggered, it can send the video to a specific e-mail address, (only one receiver email is allowed) transmit the video to remote ftp server, trigger the relay, and save video to local SD card.
Alarm Input Setting: The GPIO I/O port input activates related functions when I/O input is triggered
GPIO Output Setting: The GPIO I/O port output activates a switch, slide switch or pan/tilt Module
for use with any standard relay box
GPIO 0
ALARM INPUT Normal: 3.3V (The voltage differential from GPIO pin & GND)
GPIO 1
GPIO 2
Active: 0V (GPIO 0 & GPIO1 link to PIN2 GND)
ALARM OUTPUT
Normal: 3.3V (The voltage differential from GPIO pin & GND)
GPIO 3
Active: 0V (GPIO 0 & GPIO1 link to PIN2 GND)
37
I/O Setting/cont
I/O Setting:
The 6521 & 6522 supports 1 input/1 output. When a input is triggered, it can send the video to a specific e-mail address, transmit the video to remote ftp server, trigger the relay, or save video to your SD card. (Note: 6521 dome offers an SD card option, 6522 does not)
GPIO INSTALLATION EXAMPLE 1: Floodlight
Trigger a normally off (Normally Open) alarm siren that activates when an event/motion occur at the COM terminal.
GPIO INSTALLATION EXAMPLE 2: Light Bulb
Trigger the normal on (Normally Closed) indoor light off when an event/motion occurs on the COM terminal.
Log List: This menu provides access to the logs the 6521 or 6522 can create.
Log List
38
SD Card
Recommended SD Cards
SanDisk 128M SanDisk 256M SanDisk 512M SanDisk 1G SanDisk 2G SanDisk 4G
SD Card recording is only available on the 6521, Currently, this function is not supported on the 6522. Below is a picture showing the location of the SD card in the 6521 dome. Using the SD card could affect the frame rate of the video. Make sure the SD card is pushed into the slot completely.
：
Tracend 128M 80X Tracend 256M 80X Tracend 512M 80X Tracend 1G 80X Tracend 2G 80X Tracend 4G 80X
39
The capacity of the SD card is shown in the SD card menu. Below is a list of the video files recorded. The video format recorded to the SD card is AVI. Double click the video to open Windows Media Player and play the selected file. To delete the video, check it with the mouse, then click the Del. When the SD card is full, it will automatically delete the oldest video files.
Port Forwarding
In order to view the IP camera from outside of your home or business network, port forwarding configuration will be required in your router.
Below are several points of reference regarding port forwarding.
1.) Http://en.wikipedia.org/wiki/Port_forward The wikipedia page explains what port forwarding is, how it is used and what it’s applications are.
*This website is not affiliated with Channel Vision.
2.) Http://screenshots.portforward.com/ This website contains picture by picture walkthroughs on how to port forward most routers on the market.
*This website is not affiliated with Channel Vision.
Port Forwarding LG Routers
In the example below, there is a 6521 running on port 8002 on the LAN.
1.) Add the IP information, including the desired port into the port forwarding tab of “advanced” in the router
2.) Check “Enable Port Forwarding”
40
3.) Click ‘Add”
4.) Click “Select”
5.) Select “Apply” to enable your new port forwarding rule
6521 Specifications
CPU: ARM 9; 32 Bit RISC DDR2: 256MB Flash: 16MB Image Sensor: 1/3” CMOS (2 Megapixel) Sensitivity: 0 Lux (IR On) DC Iris: Yes Lens Type: Vari-focal 2.7 - 9mm LED’s: 18 IR LED (15 Meter Range) I/O: 1 in / 1 Relay Out Video Output: BNC, Composite Video Audio In: 1 Input, RCA Audio Out: 1 Output, RCA Power Over Ethernet: Supported, Designed For 802.3af Standard, 47V Recommended Power Consumption: 12vDC 480mA (IR on) 3 Axis Bracket: Pan: 175° / Tilt 75° / Rotation 180° Operating Temp.: 0° - 40° Celsius / 32° - 104° Fahrenheit Dimensions: 141mm x 132mm / 5.5in x 5.20in Ethernet: 10/ 100 Base-T Network Protocol: HTTP, TCP/ IP, SMTP, FTP, PPPoE, DHCP, DDNS, NTP, UPnP, 3GPP Video Resolution: 1600x1200,1280x1024,1280x960,1280x720,800x600,640x480,320x240,176x144 Video Adjust: Brightness, Contrast, Sharpness, BLC, Night Mode Image Snapshot: Yes Full Screen Viewing: Yes Privacy Mask: Yes, 3 different areas Compression Format: H.264/ JPEG (MJPEG)/ MPEG4 (3GPP only) Video Bitrate Adjust: CBR, VBR Motion Detection: Yes, 3 different areas Triggered Actions: Mail, FTP, Save to SD card, Relay Pre/Post Alarm: Yes, configurable Security: Password protection Firmware Upgrade: HTTP mode, can be upgraded remotely Simultaneous Users: Up to 10 Audio: Yes, 2-way Weatherproof Rating: IP66
SD card management
Recording Trigger: Motion Detection, IP check, Network Failure, (wire only) Schedule, Relay Video Format: AVI, JPEG Video Playback: Yes Specific File Deletion: Yes
System Requirements
OS: Windows 2000, XP, Vista, 7
Browser: Microsoft IE 6.0 or above Suggested Hardware: Intel Dual Core 1.66G,RAM: 1024MB, Graphic card: 128MB Minimum Hardware: Intel-C 2.8G, RAM: 512MB, Graphic card: 64MB
41
*Specifications subject to change without notice.
6522 Specifications
CPU: ARM 9; 32 Bit RISC DDR2: 256MB Flash: 16MB Image Sensor: 1/3.2” CMOS (2 Megapixel) Sensitivity: 0 Lux (IR On) DC Iris: Yes Lens Type: Vari-focal 3.6 - 16mm LED’s: 35 IR LED (20 Meter Range) I/O: 1 in / 1 Relay Out Video Output: BNC, Composite Video Audio In: 1 Input, RCA Audio Out: 1 Output, RCA Power Over Ethernet: Supported, Designed For 802.3af Standard, 47V Recommended Power Consumption: 12vDC 500mA (IR on) Operating Temp.: 0° - 40° Celsius / 32° - 104° Fahrenheit Dimensions: 83mm(W) x 180mm(D) / 3.27in (W) x 7.09in(D) Ethernet: 10/ 100 Base-T Network Protocol: HTTP, TCP/ IP, SMTP, FTP, PPPoE, DHCP, DDNS, NTP, UPnP, 3GPP Video Resolution: 1600x1200,1280x1024,1280x960,1280x720,800x600,640x480,320x240,176x144 Video Adjust: Brightness, Contrast, Sharpness, BLC, Night Mode Image Snapshot: Yes Full Screen Viewing: Yes Privacy Mask: Yes, 3 different areas Compression Format: H.264/ JPEG(MJPEG)/ MPEG4 (3GPP only) Video Bitrate Adjust: CBR, VBR Motion Detection: Yes, 3 different areas - Triggered Actions: Mail, FTP, Save to SD card, Relay Pre/Post Alarm: Yes, configurable Security: Password protection Firmware Upgrade: HTTP mode, can be upgraded remotely Simultaneous Users: Up to 10 Audio: Yes, 2-way Weatherproof Rating: IP66
System Requirements
OS: Windows 2000, XP, Vista, 7
Browser: Microsoft IE 6.0 or above Suggested Hardware: Intel Dual Core 1.66G,RAM: 1024MB, Graphic card: 128MB Minimum Hardware: Intel-C 2.8G, RAM: 512MB, Graphic card: 64MB
*Specifications subject to change without notice.
42
1
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for one year from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment. This warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling (800) 840­0288 toll free. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory-authorized service center.
Channel Vision products are not intended for use in medical, lifesaving, life sustaining or critical environment applications. Channel Vision customers using or selling Channel Vision products for use in such applications do so at their own risk and agree to fully indemnify Channel Vision for any damages resulting from such improper use or sale.
www .c ha nn el vi sio n. co m
234 Fischer Avenue, Costa Mesa, California 92626 USA
(714)424-6500 (800)840-0288 (714)424-6510 fax
email: techsupport@channelvision.com
500-296 rev E
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use