6144
Indoor PTZ Dome Camera with Fan
6154
Outdoor PTZ Dome Camera with Fan & Heater
9
The 6144 (Indoor) and 6154 (Outdoor) high-resolution Pan
Tilt Zoom Color Dome Cameras are perfect for high-end
surveillance systems. Their built-in multi-protocol decoders
allow the cameras to be controlled using either Pelco D or
Pelco P protocols. Built-in heating elements and cooling fans
ensure continued operation even when under extreme
ambient conditions.
Features:
High quality color CCD image sensor
h
500 TV lines of resolution
h
Built-in multi-protocol decoder: Pelco P or Pelco D
h
Up to 256 selectable camera IDs
h
360º Pan rotation and 90º Tilt movement
h
Non-volitile memory retains settings during power loss
h
Built-in heating elements(6154 only) and cooling fans
h
Pan Tilt Zoom Dome Cameras Include:
6154 Camera 6144 Camera
Wall Mount Pendant Mount
Accessories:
Power Supply
Accessory Pack
2
Camera Pigtail
Length: 80”
Wiring Detail
Orange (RX+)
Yellow (RX-)
Black Video Gnd (VG)
Clear Video Signal (VO)
Black (AC24V)
Red (AC24V)
Dimensions
Units: mm
6144 6154
120.0
120.0
215.5
99.5
52.0
224.5
71.1
Ø101.0
118.4
141.7
196.5
99.5
52.0
71.1
Ø101.0
118.4
141.7
Accessing the DIP Switches
There are several configuration DIP switches located
underneath the dome cover of the camera. Please follow the
steps below to safely remove the dome cover. After the
configuration switches have been set, follow these steps in
reverse order to reinstall the dome cover.
See the following page for configuration details.
DIPDIP
ONON
DIPDIP
ONON
33
11
22 55
44
77
88
66
33
11
44
22
2. To release the inner dome, remove
the 4 screws holding it in place.
1. Unscrew the clear dome to remove it.
3
DIPDIP
ONON
33
11
Auto Detect
Pelco-D(2400)
Pelco-P(4800)
2400bps
4800bps
9600bps
19200bps
44
22
DIP Switch Settings
PTZ Protocol Settings...
These DIP switches select the PTZ protocol and
baud rate that will be used for communication
between the camera and PTZ controller.
Follow the table below.
4
1
Off Off OffOff
Off On OffOff
On On OnOff
OffOff
OnOff
OffOn
OnOn
3
2
Baud
Rates
Example... This switch
configuration will make
the camera respond to
Pelco-D at 2400bps.
DIPDIP
ONON
33
11
44
22
ONON
DIPDIP
Camera ID Settings... These DIP
switches set the camera ID that will
33
11
22 55
44
77
66
allow your PTZ controller to send
88
discrete commands to move this
specific camera. You can set the ID
anywhere between 0 and 255. See the
example below to learn how to set these
switches.
ONON
DIPDIP
Example... To calculate the camera ID,
add up all the values of the switches in
33
11
4
44
22 55
77
66
the “ON” position.
88
Switch
Value
128
64
32
16
Position
8
4
2
1
Switch
Off
On
Off
Off
Off
On
Off
Off
Camera ID =
Camera ID
Calculation
0
64
0
0
0
4
0
+
0
68
Installation
Note: The installation of the 6154 camera is shown below. The 6144 comes with a different
mount, but the installation is otherwise identical.
1. Drill a hole for wiring to exit
Wall Mount
Camera
Pigtail
BNC connector
Wire Extensions
(not included)
the wall.
2. Feed camera pigtail through
the base of the wall mount.
3. Attach mount to wall with
screws.
4. Connect camera pigtail to the
base of the camera.
5. Secure the camera to the
mount using the set screw.
Set Screw
RS-485
Connector
To Video
Display
To PTZ
Controller
Crimp-on splice
connectors
(not included)
Power Supply
6. Connect the camera
pigtail to wire extensions
or directly to a video
display system.
7. Connect the BNC video
output to a monitor or
distribution system.
8. Connect RS-485 wires to
PTZ controller.
9. Connect power supply.
5
Trouble Shooting
Problem
No motion and no
video output
Normal Video output
but abnormal motion
Have motion control,
but no video
Possible Cause Solution
Power supply is
disconnected or
damaged.
Power supply voltage
is too low.
Faulty coax
connection.
Check power
supply. Replace
if needed.
Make sure to
use the correct
power supply.
Move the power
supply closer to
the camera.
Check with
cable tester or
verify cable by
sending known
good video
signal through
it.
Normal video output,
but no motion control
6
Camera protocol
does not match
controller.
Check the DIP
Switches.
*Specifications
Image Sensor: 1/3” Hi-Res CCD
Picture Elements: NTSC: 768x494
Resolution: 500 lines
S/N Ratio: More than 48 dB
Min Illumination: 0.7 Lux @ F1.8
Electronic Shutter: 1/60s - 1/120,000s
Iris Control: Automatic/Manual
White Balance: Automatic
Gamma Characteristic: 0.45
Focus: Auto/Manual/One push
Optical Zoom: 10X, f = 3.8 to 38.00mm
Min. Focal Distance: 1.000mm
Digital Zoom: Off/On (X2 - X10)
Zoom Speed: 1.67 sec: Wide to Tele
Angle Field of View: H: 51.2°(wide) - 5.58º(tele)
V: 39.3°(wide) - 4.27º(tele)
Sync. System: Internal
Power Supply: 24VAC, 2Amps
Power Consumption: 38Watts (max with heaters on)
Video Output: 1 Vp-p @ 75 ohms
RS-485 Camera ID: Selectable: 0-255
Weather Resistance: 6154: IP66 for Outdoor use
6144: Indoor use only
Operating Temp (6144): -10°C to +45°C (14°F to 113°F)
Operating Temp (6154): -30°C to +60°C (-22°F to 140°F)
Operating Humidity: 0% to 90% (non-condensing)
Storage Temp: -20°C to 60°C (-4°F to 140°F)
Storage Humidity: 0% to 95% RH
*Specifications subject to change without notice.
7
Channel Vision Technology will repair or replace any defect in
material or workmanship which occurs during normal use of this
product with new or rebuilt parts, free of charge in the USA, for two
years from the date of original purchase. This is a no hassle warranty
with no mail in warranty card needed. This warranty does not cover
damages in shipment, failures caused by other products not supplied
by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only
to the original purchaser, and a purchase receipt, invoice, or other
proof of original purchase date will be required before warranty
repairs are provided.
Mail in service can be obtained during the warranty period by calling
(800) 840-0288 toll free. A Return Authorization number must be
obtained in advance and can be marked on the outside of the shipping
carton.
This warranty gives you specific legal rights and you may have other
rights (which vary from state to state). If a problem with this product
develops during or after the warranty period, please contact Channel
Vision Technology, your dealer or any factory-authorized service
center.
w ww .chan n el vision . com
234 Fischer Avenue, Costa Mesa, California 92626 USA
(714)424-6500 (800)840-0288 (714)424-6510 fax
email: techsupport@channelvision.com
500-230 rev D
Loading...