Channel Vision 6117 User Manual

Specifications:

Image Sensor:

Picture Elements:

Resolution:

S/N Ratio:

Min Illumination:

Electronic Shutter:

Iris Control:

Flickerless Mode:

Gain Control:

Auto White Balance:

Back Light Comp.:

Gamma Characteristic:

Camera Lens:

Focal Length & App. Ratio:

Angle Field of View:

Sync. System:

Power Requirements:

Power Consumption:

Video Output:

Operating Temp:

Sony 1/3” Hi-Res Super HAD

NTSC: 768x494

550 lines

More than 48 dB

0.4 LUX @ F2.0

1/60s - 1/100,000s, ON/OFF Switch-able

Built-in DC Drive Iris Control

1/60s ON/OFF switchable

High/Low switchable

Color Temperature: 2500K-9500K

ON/OFF switchable

0.45

Vari-Focal with DC Drive Iris Lens

3.7mm-12mm, F1.6-3.0

Wide: 71.6°x55.8°, Tele: 23.8°x17.9°

Internal, Negative sync.

12VDC

195 mA

1 Vp-p @ 75 ohms

-10°C to 50°C (14°F to 122°F)

Specifications subject to change without notice.

CHANNEL VISION

Limited Warranty

Channel Vision Technology will repair or replace any defect in material or workmanship which occurs

during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from

the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This

warranty does not cover damages in shipment, failures caused by other products not supplied by Channel

VisionTechnology,orfailures due to accident, misuse, abuse, or alteration of theequipment.This warranty

is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original

purchase date willberequiredbefore warranty repairs are provided.

Mail in service can be obtained during the warranty period by calling [phone] toll free. A Return

Authorization number must be obtained in advance and can be marked on the outside of the shipping

carton.

This warranty gives youspecificlegalrights and you may have other rights (whichvaryfromstate to state).

If a problem with this product develops during or after the warranty period, please contact Channel Vision

Technology, your dealeroranyfactory-authorized service center.

500-140 Rev B

6117

Vandal-Proof Color Dome Camera

8

The is a vandal-proof color dome camera. Its extremely

611

6117

rugged construction makes it ideal for CCTV installations
where the camera will be subjected to physical abuse.
Typical applications included factories, warehouses, and
other industrial buildings.

Features:

High quality 1/3” Sony Hi-Res Super HAD CCD sensor

h

550 TV lines of resolution

h

1. Connect wiring

2. Mount base

Model

3. Adjust camera settings

4. Attach dome

FL: Flicker Lens ON/OFF
AGC: Auto Gain Control High/Low
AES: Auto Electronic Shutter ON/OFF
BLC: Back Light Compensation ON/OFF

VR Adjustment level for DC Drive Lens
(Switch AES OFF before adjusting)

7

Camera Adjustments

Digital Signal Processor (DSP) chip-set provides image

h

control

High sensitivity, low smear, high anti-blooming and high

h

S/N ratio

Automatic Gain Control (AGC) and Auto White Balance

h

(AWB)

3-Axis mechanism for easy rotation and adjustment

h

Zoom

Dome CoverDome Base & Camera

Focus

Screws

Power Supply

Adjusting the 3-Axis Mount

To p

To p

Rotate

Hex Wrench

To p

2-Conductor power

supply extension

(not included)

BNC connector

Coax extension

(not included)

To Monitor

or

Video distribution

Installation:

Using the wrench, loosen the 4 screws securing the

h

Crimp-on splice

connectors

(not included)

Power supply

(included)

dome cover to the base.

Drill a hole in the wall or ceiling for wiring (see diagram).

h

If necessary, attach the camera’s video output to a coax

h

extension that is long enough to reach your monitor or
video distribution equipment.

If necessary, cut the connector off of the end of the power

h

supply and splice in an extension using crimp-on
connectors.

Mount the base with the provided screws.

h

Tilt

Rotate

1. Tilt camera to
desired angle

2

2. Rotate camera to
desired direction

3. Rotate camera ring
so that the image
appears right side up

Move the camera body to adjust the view and make

h

electronic adjustments using the dip switches.

Re-attach the dome cover by tightening the four screws

h

with the provided wrench.

3