ChangHong EF24F898SD Operation Manual [ml]

Operation Manual

Model: EF24F898SD

CHANGHONG EUROPE ELECTRIC S.R.O

Jankovcova 1037/49,170 00 Praha 7,Czech Republic	24	UK
Tel: [phone]
Fax: [phone]	TV	CZ
Service E-mail: [e-mail]		SK
Web site: www.changhongeurope.com		ES
		PL

Contents UK

Warning……………………………………………………………………..…..……… 1 Safety instructions……………………………………………………....…………… 3 Getting Started…………………………...………………………..……..…………… 5

Using the remote control…………………………………………………….……… 5 Installing Batteries in the Remote Control……………………………..…………. 5 Battery replacement……………………………..……………………….………… 5

Connection and setup…………………...…………………………………………… 6

Cable Installation……………………………………………………………………. 6

Remote Control…………………………..…………………………………………… 7 Basic Operation……………………………………………………………………... 9

QUICK START GUIDE……………….………………………………………….….. 9 Turning on and off the TV…………………………………………………………. 10 Programme Selection…………….……………………………………………… 10 Volume adjustment………………………………………………………………… 10 Changing the Input Source…..…………………………………………………... 10

Menu Operation……………………………………………………………………… 11

How to Navigate Menus…………………………………………………………... 11

Channel Menu……………………………………………………………………… 11
Picture Menu……………………………………………………………………….. 15
Sound Menu………………………………………………………………………... 15
Timer Menu…………………………………………………………………………. 16
Option Menu………………………………………………………………………... 16
Lock Menu………………………………………………………………………….. 18
Using DMP mode…………………………………………………………………. 19
MHEG5……………………………………………………………………………… 21
Important Unique Buttons.................................................................................	22
PROGRAMME GUIDE………………………………….………………………… 22
Channel List………………………………………………………………………… 22
Favorite List………………………………………………………………………… 22
Teletext………………………………………………………………………………... 23
Using the teletext feature…………………....................................................... 23

Troubleshooting Guide…………………………………………………………….. 24

Troubleshooting…………….……………………………………………………... 24

Maintenance………………………………………………………………………... 25

Warning

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

REGULATORY INFORMATION

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

CAUTION

DO not attempt to modify this product in any way without written authorization from supplier. Unauthorized modification could void the user's authority to operate this product.

It is not recommended to keep a certain still image displayed on the screen for a long time as well as displaying extremely bright images on screen.

1

Warning

WARNING

To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture.

Don’t use the apparatus in tropical climates.

The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.

The Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Attention should be drawn to the environmental aspects of battery disposal. Don’t throw used batteries in dustbin. Please contact your retailer in order to protect the environment.

Keep minimum distances (5cm) around the apparatus for sufficient ventilation; (Minimum distance around the apparatus for sufficient ventilation.)

No naked flame sources, such as lighted candles, should be placed on the apparatus;

To prevent the spread of fire, keep candles or other open flames away from this product at all times.

The device may be malfunction when under electrostatic discharge. It can be manually resumed by power off and power on again.

CAUTION connecting the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and its if appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

The MAINS plug is used as the disconnect device, and the disconnect device shall remain readily operable.

The apparatus shall be connected to a MAINS socket outlet with a protective

earthing connection.

Figures and illustrations in this User Manual are provided for reference only and

may differ from actual product appearance. Product design and specifications may be changed without notice.

2

Safety instructions

IMPORTANT SAFETY INSTRUCTIONS
1.	Read these instructions.									7. Do not block any of the ventilation
2.	Keep these instructions.									openings. Install in accordance with
3.	Heed all warnings.									the manufacturer's instructions.
4.	Follow all instructions.

5. Do not use this apparatus near water. 8. Do not install near any heat source such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

6. Clean only with a dry cloth.

9.Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

3

Safety instructions

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

11.Only use the attachments/ accessories specified by the manufacturer.

12.Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

ON DISPOSAL

-The fluorescent lamp used in this product contain a small amount of mercury. -Do not dispose of this product with general household waste.

-Disposal of this product must be carried out in accordance to the regulations of your local authority.

NOTE

-If the TV feel cold to the touch, there may be a small "flicker" when it is turned on. This is normal, there is nothing wrong with TV.

-Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However there have no adverse effect on the monitor's performance.

-Avoid touching the screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effect on the screen.

4

Getting Started

Using the remote control

When using the remote control, aim it at remote sensor on the television. If there is an object between the remote control and the remote sensor on the unit, the unit may no operate.

Point the remote control at the REMOTE SENSOR located on the television.

When using this television in a very brightly lit area, the infrared REMOTE CONTROL SENSOR may not work properly.

The recommended effective distance for using the remote control is about 7 metres.

Installing Batteries in the Remote Control

1. Open the cover at the back of the remote control.

2. Install two AAA size batteries. Make sure to match the “+” and “-” ends of the batteries with the diagram inside the compartment.

3. Replace the cover.

Battery replacement

You will need to install the supplied batteries into the remote control to make it operate following the instruction below.

When the batteries become weak, the operating distance of the remote control will be greatly reduced and you will need to replace the batteries.

Notes on Using Batteries:

The use of the wrong type of batteries may cause chemical leakage and/or explosion. Please note the following:

Always ensure that the batteries are inserted with the + and - terminals in the correct direction as shown in the battery compartment.

Different types of batteries have different characteristics. Do not mix different types.

Do not mix old and new batteries. Mixing old and new batteries will shorten battery life and/or cause chemical leakage.

Replace batteries as soon as they do not work.

Chemicals which leak from batteries may cause skin irritation. If any chemical matter seeps out of the batteries, wipe it up immediately with a dry cloth.

The batteries supplied with the product may have a shorter life expectancy due to storage conditions. Remove the batteries whenever you anticipate that the remote control will not be used for an extended period.

The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION:

It may result in an explosion if batteries are replaced incorrectly.

Only replace batteries with the same or equivalent type.

5

Connection and setup

Cable Installation

Please read the relevant content in "Notice for Maintenance and Safety" carefully before the installation and use.

1.Take out the TV from the package and put it in a drafty and flat place.

NOTE:

When you plug or unplug the TV, computer or other equipments, you must make sure that the AC power has been already shut down; when unplugging the power cable or signal cable, please hold the plug (the insulated part), do not draw the body of the cable.

2.The RF output terminal can be connected with the RF input port of the TV.

3.The output AV terminal of DVD can be connected with the AV input port of the TV through AV cable.

4.Connect one end of the VGA cable with the VGA port on computer, connect the other end of the VGA cable with the VGA port on the TV, and tighten the bolts clockwise on the each end of VGA cable.

NOTE:

While connecting the 15-pin VGA, please do not insert the plug overexertedly, for fear the pin might be broken.

5.Connect one end of the HDMI cable with HDMI output port, connect the other end of the HDMI cable with the HDMI port on the TV.

NOTE:

While connecting the HDMI, please aim at carefully, do not insert overexertedly, for fear the pin might be broken.

6.Check and make sure that all AV cables are connected with the corresponding ports correctly.

7.Connect SCART socket input or output from an external device to these jacks.

8. Connect the AC power cable with 100-240V~ power supply.

NOTE:

The range of power input for the TV is 100-240V~ 50/60Hz, do not connect the TV power input port with the AC power out of the above range.

Please hold the insulated part of the plug when you are unplugging the power cable, do not touch directly the metallic part of the cable.

6

Remote Control

The buttons of the original remote control are as following:

1.: Power, switch on or off TV set.

2. INFO: Press to display the current program information on the screen. i : Go to the index page.

3. : Press to mute or restore sound.

4. NUMBER BUTTONS: Choose channels or password importation.

5.SOURCE: Press to select signal source.

? : Reveal the hidden information of some teletext pages.

6. AUDIO (∞I/II): The button can be used to switch between NICAM DUAL / NICAM DUAL / NICAM DUAL + /MONO and switch Audio language in DTV mode.

7.: Press to select different images

				sizes.
				: Change size of teletext screen in
				display mode.
			8.	: Return to last viewed program.
			9. MENU: Press to enter the menu screen
				for various optional adjustable settings.
			10.	EXIT: Return the last layer OSD Menu or
				exit OSD Menu.
			11.	ENTER: Press to execute the selected
	DMP	25		item in the menu screen or enter the
				desired value in any input mode.
	2777	26
			12.	▲/▼/◄/►: To select the direction.

13.VOL+/VOL-: Press to adjust the volume level up or down.

14.CH+/CH-: Press to select channels in ascending or descending order.

15.SLEEP: Press to set the sleep timer. When the preset length of time has passed, the TV set enters standby mode.

16.LIST: Press to call up the channel list. Press again to exit it.

17.EPG: Electronic Program Guide, use in the DTV mode.

7

Remote Control

DMP	25
2777	26

18.: Switch on/off the favorite programs list.

19.COLOR BUTTONS: Red/ green/ yellow/ blue key navigation link.

: Fast reverse (in DMP mode).

: Fast forward (in DMP mode).

: Previous (in DMP mode).

: Next (in DMP mode).

20.STILL: Press to hold the picture.

: Hold the teletext page on display, press again to release.

: Stop (in DMP/PVR mode).

21.: Enter the Teletext, press again for MIX mode, press this button again to exit.

: Play / Pause (in DMP/PVR mode).

22.: Enter subtitle mode or subpage.

23.RADIO: Press to interchange Radio and DTV programs when there is Radio program (In DTV mode).

24.: Cancel the teletext but not to exit teletext, press again to exit.

25.: Press button to start recording. Recording in use.(In PVR mode).

26.INDEX: Press to enter the Recorded list. (In PVR mode) Change the list by TIMER or CHANNEL. (In PROGRAMME GUIDE menu)

27.DMP: Press to switch to the DMP source.

NOTE:

All pictures in this manual are examples, only for reference, actual product may differ from the pictures.

The buttons not mentioned here are not used.

8

Basic Operation

QUICK START GUIDE

•Connection

1.Connecting the mains and antenna.

2.If TV has a power switch, turn it on firstly. Then press Power button on the remote to turn on the TV.

•Initial Setup

When the TV is initially powered on (Or no preset channels), a sequence of on-screen prompts will assist in configuring basic settings.

1.Selecting a language

Press the▲/▼/◄/►button, then press the ENTER button.

Select the desired OSD (On Screen Display) language.

2.Selecting an antenna source

Press the▲/▼button, then press the ENTER button.

When selecting Air

→Press the▲/▼/◄/►button to select the appropriate country and tune type, then press the ENTER button.

→The TV starts Auto tuning.

When selecting Cable

→A step appears allowing you to set parameters to the channels. For more information, refer to Channel (Auto Tuning).

→Press the▲/▼/◄/►button to select the appropriate country and tune type, then press the ENTER button.

→The TV starts Auto tuning.

When selecting Satellite

→Press the▲/▼/◄/►button to select the appropriate country, then press the ENTER button.

→A step appears allowing you to set parameters of the Satellite. For more information, refer to Channel (Auto Tuning).

→When setting is completed, press the blue button to enter the Channel Tuning menu. Select the ENTER button to start Auto tuning.

9

Basic Operation

Turning on and off the TV

•Turn on the TV

Connect the power cable, at this time the TV will enter standby mode. Press the button on remote control can turn on TV from standby mode.

•Turn off the TV

Press the button on the remote control to enter standby mode.

Do not leave your set in standby mode for long periods of time. It is best to unplug the set from the mains and aerial.

•No signal

There is No Signal menu on screen when there is no input signal. In TV/DTV mode, if there is no signal in five minutes, the TV will turn off automatically. In PC-RGB mode, the TV set will automatically turn off in 16 seconds if no input signal. When VGA cable

is connected, the TV turns on automatically.

Programme Selection

•Using the CH+/CHon the panel of TV or on the remote control.

Press CH+ to increase channel number. Press CH - to decrease channel number.

•Using 0- 9 digital buttons.

You can select the channel number by pressing 0 to 9. (In TV, DTV mode)

•Example

To select - channel (e.g. Channel 5): Press 5.

To select -- channel (e.g. Channel 20): Press 2 and 0 in a short time.

Volume adjustment

•Press the VOL+/- button to adjust the volume.

•If you want to switch the sound OFF, press the .

•You can release mute by pressing the or increase/decrease the volume.

Changing the Input Source

You can select the input source by pressing the SOURCE button on the remote control. Press the▲/▼button to cycle through the input source, and press the ENTER button to confirm your choice.

NOTE:

The picture is just for reference. Please operate with the OSD MENU of concrete TV and refer to the AV terminal board.

10

Menu Operation

How to Navigate Menus

Before using the TV follow the steps below to learn how to navigate the menu in order to select and adjust different functions. The access step may differ depending on the selected menu.

1.Press the MENU button to display the main menu.

2.Press the◄/►button to cycle through the main menu.

3.Press the▲/▼button to select the desired sub item.

4.Press the ENTER button to access the submenu.

5.Press the ▲/▼/◄/► button to select the desired value. The adjustment in the OSD may differ depending on the selected menu.

6.Press the MENU button to return to the previous menu.

7.Press the EXIT button exit from the menu.

NOTE:

When an item in MENU is displayed gray, it means that the item is not available or cannot be adjusted.

Buttons on the TV have the same function as corresponding buttons on the remote control. If your remote control is lost or couldn’t work, you may use the buttons on the TV to select menus. This manual focuses on operation of the remote control.

Configuring the Channel Menu

•Antenna

Selecting an antenna source.

* When TV signals is Air.

•Auto tuning

Select the ENTER button to start Auto tuning.

1.Select the country and tune type for channels.

2.The TV will begin memorizing all of the available channels.

Once the progress bar is full, the found channels will be stored and the unit will proceed to the search for TV, DTV, Radio and Data.

If you press the MENU button in TV searching, the Auto tuning will skip to DTV searching as the suggestive picture shows.

•DTV Manual Tuning

Manual store for digital channels.

Press the ◄/►button to select channel. Press the ENTER button to search.

When a channel is found, the searching process will stop, the channel will be saved with current channel number.

If the program is not your expected one, please press the ◄/►button to continue the searching. Press the EXIT button to exit.

11

Menu Operation

* When TV signals is Cable.

•Auto tuning

Select the ENTER button to start Auto tuning. 1. Adjust the Cable Scan Menu.

-Scan type: Scans for all active broadcast station channels and stores them in the TV.

If you select Quick Scan, you can set up the Frequency, Network ID and Symbol (Ks/s) manually by pressing the button on the remote control. Quick Scan can only search DVBC digital programmes, can not search for ATV programmes.

If you select Full Scan, the Auto Tuning will search through all or appointed frequencies to find available channels.

-Frequency: Enter a user-defined frequency. (Differs in each country)

-Network ID (Auto/Manual): Selects the Network ID setting mode among Auto or Manual. When Network is Manual, you can set up Network ID using the numeric buttons.

-Symbol (Ks/s): Selects the Symbol (ks/s) setting mode among Auto or Manual. When Symbol (ks/s) is Manual, you can set up Symbol (ks/s) using the numeric

buttons.

When you are satisfied with your setting, press ENTER button.

2.Select the country and tune type for channels.

3.The TV will begin memorizing all of the available channels.

•CADTV Manual Tuning

Frequency, Symbol (ks/s), and QAM Type are needed in order to add a programme correctly in DVB cable mode. Please inquire of the cable service provider about the correct values.

•ATV Manual Tuning

Manual store for ATV channels. Press the▲/▼ button to select items. Press the◄/► button to adjust it. Press the red button to save it. Press the EXIT to exit.

12

Menu Operation

* When TV signals is Satellite.

• Auto tuning

Press the ENTER button.

Satellite Setup

■Transponder: Press the INDEX button to switch between the satellite list and the corresponding transponder list.

■▲/▼: Press the▲/▼button to select the satellite/transponde from the list.

■CH+/CH-: Press the CH+/CH- button to page up or down the satellite/transponder list.

■Delete: Press the red button to delete the current satellite/transponder.

■Edit: Press the green button to edit the current satellite/transponde.

■Add: Press the yellow button to add a new satellite/transponde.

Press the ► button to configure the satellite.

■LNB TYPE: Select the LNB type.

■LNB Power: Select the power supply type for the LNB.

■22KHz: 22KHz SWITCH. Select the 22KHz depending on the LNB type.

■Toneburst: You can choose one of two satellites. Used to choose proper device.

■DiSEqC1.0: You can choose one of four satellites. Used to choose proper device.

■Motor: Sets the positioned type between DiSEqC1.2 and USALS.

When Motor is set to DiSEqC1.2 or USALS:

- Set Position: Press the ENTER button to set Position. Move Auto: Rotates the antenna automatically.

Move Continue: Rotates the antenna until the rotation has been completed or stopped manually.

Move Step: Rotates the antenna in accordance with the step value. Enables the antenna make a finer adjustment.

Goto Position: Rotates the antenna to the stored satellite position. Goto Reference: Drive antenna to zero position.

GotoX: Moves the antenna to the location specified by Set Location. Store Position: Stores current position as the selected positioner limit.

- Set Limit: Press the red button to set Limits to the scope of satellite antenna rotation.

Move Continue: Rotates the antenna until the rotation has been completed or stopped manually.

Move Step Rotates the antenna in accordance with the step value. Enables the antenna make a fine adjustment.

Set West Limit Set the west limit value. Set East Limit Set the east limit value.

Goto Reference Drive antenna to zero position.

13

Menu Operation

Disable Limit Delete Limit settings. Allows the antenna to rotate over the full arc.

Cancel east limit and west limit. When Motor is set to USALS:

-Set Location: Press the green button to set Location.

Location Selects the Set Location mode.

Longitude Direction, Longitude Angle, Latitude Direction, Latitude Angle can be

adjusted when the Location is set to Manual.

Longitude Direction: Sets the longitude direction for the location. Longitude Angle: Sets the longitude angle for the location.

Latitude Direction: Sets the latitude direction for the location. Latitude Angle Sets the latitude angle for the location.

■Reset All: Satellite list, transponder list and some settings will be reset to the default values. After reset all, you can re-set the country while Auto Tuning.

■Quality: Display the current status of broadcasting signal.

■Scan: Press the blue button to enter the Channel Tuning menu.

Scan mode: Selects the scanning mode of the selected satellite.

Encrypted: Scan either free or all channels. Service Type: Select the channel type to memorise.

When setting is completed, press the ENTER button. Channel Tuning is started.

•Programme Edit

Press the▲/▼ button select items.

Press the red button to delete the channel.

Press the green button to rename the channel. (In TV mode)

Press the yellow button to move the channel. (Except DTV channels with LCN) Press the blue button to skip the channel.

Press the button to set the favorite channel.

The CH+/CH- button can be used to select the following or preceding page.

•Channel List Transfer

You can export all current channel information (including channel number, channel name, frequency, etc.) into the U disk, as the channel information backup for this unit. The system will automatically create a data file to store the channel information has been exported.

If you can not restore the initial channel information after SORT, MOVE, DEL, SKIP, LOCK, etc. operations, you can import the channel information from the USB.

•CI Information (In DTV mode)

This function enables you to watch some encrypted

services (pay services).

Please insert CI card into the PCMCIA slot according to the arrow on the CI card.

When the TV is initially powered on, or insert the CI card the first time.You should wait for several minutes for reading the CI key properly.

NOTE:

The function can only be gotten when CI slot is available.

This OSD is only for illustration and the menu options and screen format will vary according to the Digital pay services provider.

It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer.

Please do not insert or pull out the CI card when power on.

Do not insert or pull out the CI card frequently so as to avoid any damages of the TV and the CI card.

During initialization of the CI card, please don't operate the TV.

14

Menu Operation

Configuring the Picture Menu

•Picture mode

You can select the type of picture which best corresponds to your viewing requirements. Contrast, Brightness, Saturation, Sharpness and Tint (NTSC) can be adjusted when the picture mode is set to User.

The manufacture's recommendation mode is VIVID.

•Colour Temp

Select the colour temperature of the picture.

•Aspect Ratio

You can select the picture size which best corresponds to your viewing requirements.

•DNR

Reduces screen noise without compromising video quality.

•Screen (In PC-RGB mode)

Auto Adjust: Adjust the image automatically.

H Position: Centre the image by moving it left or right. V Position: Centre the image by moving it up or down. Size: Adjust the screen size.

Phase: Adjust when characters have low contrast or when the image flickers.

Configuring the Sound Menu

•Sound mode

You can select a sound mode to suit your personal preferences. Treble and Bass can be adjusted when the sound mode is set to User.

•Balance

You can adjust the sound balance of the speakers to preferred levels.

•AVL (Auto Volume Level)

AVL automatically remains on the same level of volume if you change programmes. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time when the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each program.

•Surround Sound

You can select a desired Surround Sound mode.

15

Menu Operation

•AD Switch (In DTV mode)

This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can turn the Audio Description On or Off and control the volume.

Configuring the Timer Menu

•Clock

You can display either the DTV Signal Stream Time or set the System Time.

•Off Time

Set the time for the TV to switch off.

•On Time

Set the time for your TV to turn on.

The TV must be in standby mode for the On Time to work.

•Sleep

Select the time to turn the TV to standby mode automatically.

•Auto Sleep

Select the Auto Sleep time you want.

The TV will enter into standby mode automatically when there is no any operation in set time (the set time is 4 hours when leave the factory).

•Time Zone

Select your time zone.

Configuring the Option Menu

•Language

Select your preferred On Screen Display language.

•Audio Language

Select your preferred audio language. (Available for digital channels if multiple audio languages are broadcasted.)

•Subtitle Language

Select your preferred subtitle language or turn off subtitle. (Available for digital channels if multiple subtitle languages are broadcasted.)

•Hearing Impaired

When hearing Impaired is ON, the TV screen will give some information to the people whose hearing are impaired when Hearing Impaired is Off, the information will be hidden.

•Country

Display the current country.

16

Menu Operation

•PVR File System (In DTV mode)

Select Disk: Select the disk used for PVR.

Check PVR File System: Check the disk and test the speed of the system.

USB Disk: USB activated or not. Format: Format USB disk.

Speed: Display speed of the storage device.

Free Record Limit: Select the recording duration.

Digital program recording

Insert an U disk, the system will automatically

create a folder (_MSTPVR) to store the files has been recorded.

Carve-recording begins when button pressed, and it records all the time untill button pressed or the memory is full. During the recording, press▲/▼button to zoom in/out the record menu.

Playback function

Press the button to activate Playback while recording. Press ▲/▼button to zoom in/out the Playback menu. You can operate refer to the Playback menu.

Record list

Press the INDEX button to display the Record list.

Press the ▲/▼ button to select items, then press ENTER button to play. Press the red button to delete the programme.

Press the green button to display the programme information. Press the INDEX button to sort programmes.

Press EXIT button to exit.

NOTE:

USB disk at least the capacity with 512MB.

Please format the inserted USB disk when it could not be recorded to.

During the Device formatting, do not disconnect the device while formatting is in progress. If you format the device, all files will be deleted. Before formatting your device to the TV, please back up your files to prevent them from damage or loss of data. If USB disk in some virus meeting formats turn failure.

If the usage contains many ambulation hard drives that divide area, can at PVR File System the menu win election to choose PVR to in response to the disk sign.

If PVR recording system is used all the time, it will exit PVR system automatically.

USB memory must support USB2.0 high-speed specification.

Some of nonstandard USB device may not be supported.

•Default

Restore the system settings to the factory default.

•OSD Animation

Select style of displaying menus.

•Store Demo

Switch the Store Demo on or off.

Store Demo mode is the optimal setting for store environments. If a user modifies image quality data Store Demo mode initializes the product to the image quality set by us after a certain period of time.

•Health Remind

Switch the Health Remind on or off.

While Break Time is set to On, a prompt picture will remind you to have a break at intervals of two hours.

17

Menu Operation

Configuring the Lock Menu

•Lock System

The feature can prevent unauthorized operating the TV set, unless entering 4-digit password. When Lock System is on and the system is locked, we must input the

system password at Auto Tuning, Manual Tuning, Programme Edit or Default. Press the right number buttons for the password.

The default password is 0000.

NOTE:

After a password correction has been confirmed, please remember it for entering into the Parent Guide menu, all functions can not be activated until the correct password is entered. If you forget, the super password of 1225 still valid.

•Set Password

You can set your private password. Press the number buttons on the remote control to set the new password. When the new password has been input twice, the setting is finished successfully. The TV will go back to previous menu.

•Block Program (In TV/DTV mode)

Press the green button LOCK to lock the available program you want. Press the green button again to unlock it.

•Parent Lock (In DTV mode)

This feature can prevent children watching adult’s TV programmes, according to the rating limit set. This function appearance according the information from broadcasting station. Therefore if the signal has incorrect information, this function does not operate.

18

Menu Operation

Using DMP mode

•To Access/Quit DMP mode

1.Connect an USB device.

2.Press MENU button to display the main menu. Press ◄/► button to select the Applications menu.

3. Press the ENTER button to enter the DMP mode.

4. Press EXIT button to exit.

NOTE:

Special USB device may be not or well supported.

USB max. Load: DC5V 500mA

•The formats supported

The DMP function can support the USB device with USB memory. It can play PHOTO, MUSIC, MOVIE or TEXT files.

Photo Format Support: JPEG, BMP, PNG. Music Format Support: MP3, AAC, M4A.

Movie Format Support: AVI, VOB, DAT, MPEG -1 / MPEG-2 / MPEG-4, TS/TP. Text Format Support: TXT.

NOTE:

Special algorithm documents may not be or well be supported by the USB.

The USB supports the format mentioned above, if the file format is not supported, change it to the given format.

•Main Operating Interface

19

Menu Operation

1.Use the ◄/► button to select PHOTO, MUSIC, MOVIE or TEXT. Press ENTER button enter into sub-menu.

2.Use the arrow buttons and ENTER button to enter the desired disk. Press ENTER to open the folder.

3.Use the arrow buttons to highlight the file. Use the ENTER button to mark or unmark a file. Press button to play the selected files. If no file is marked, all the files in the folder will be played in sequence after you press button.

4.Press the INFO button to display the menu screen in playing.

5.Press the to stop the playing files.

6.Press the EXIT button to return to the previous menu screen.

•Basic operation

1. Play/ Pause

Start playing the selected file of a folder or pause. 2. Stop

Stop the playing files.

3. / Fast Reverse/Fast Forward

You can press / to skip fast reverse or forward. 4. / Previous/Next

You can select the desired files manually in normal condition. 5. Red button

Select a file you want to delete press the red button to open corresponding menu then press ENTER button to delete it.

6. CH+/CH-

Page up or page down the files.

20

Menu Operation

MHEG5

MHEG5 (Multimedia and Hypermedia information coding Expert Group) is connecting the operation and function as media player. If you want to enter the MHEG5, subtitle must be set off.

Press red button or button to enter the MHEG5 menu. You can operate the TV with the suggestive information. Press EXIT button or button to exit the MHEG5 menu. Home Page:

After entering the selected item, you can view the main menu as:

Select the main item you want, you can see more particular details.

21

Important Unique Buttons

PROGRAMME GUIDE (In DTV mode)

Press EPG button to display the PROGRAMME GUIDE menu. This function let you know the detailed information of the channel, indicating the time of the program playing. From the PROGRAMME GUIDE it is possible to check the program information for the next eight days (If the information is available from the broadcaster). Press EXIT button to exit.

Record: Press red button to set the parameters for recording.

The unit is able to do schedule recording when TV is turning on or in standby mode. You can set up several schedule recording. Different schedules should not overlap. When recording starts in standby mode, the

front indicators will change color and there will be no

picture or sound from the unit. You can press button to light up the screen.

INFO: Press green button to see the detailed

information of the current channel. Schedule: Press yellow button to display the schedule list.

Remind: If you find the desired program which will be shown in the future. Press the blue button to book program.

INDEX: Change the list by TIMER or CHANNEL.

ENTER: Press to change channel.

Channel List

Press LIST button to display the Channel

List.

Press ▲/▼ to select the items, and the

channels will be changed automatically

(Air,Cable).

Press CH+/CH- button to page up or down the Channel list.

Press LIST button to exit.

Favorite List		(Satellite)
Press	button to display the favorite list.
Press ▲/▼ to select the items, and the
channels will be changed automatically.
Press CH+/CH- button to page up or down
the Favorite list.
Press	button to exit.

22

Teletext

Using the teletext feature

•Display teletext

1.Select a TV station with a teletext signal.

2.Press the button to enter teletext mode.

3.Press the button 2nd to enter Mix mode, this function enables you to superimpose the teletext page over the TV program.

4.Press the button 3rd return or exit to the normal TV/DTV mode.

•Page selection

1.Enter the page number (three digits) using the number buttons. If you press a wrong number during input, you must complete the three digit number and then reenter the correct page number.

2.The CH-/CH+ button can be used to select the preceding or following page.

•Hold

You can press the button to hold a page, and press it again to release the page.

•Index

Press the i button to enter the main index page directly.

•Enlarging Text

When a page is displayed, you can double the size of the text to make it easier to read.

1.Press the button to enlarge the top half of the page.

2.Press the button again to enlarge the bottom half of the page.

3.Press the button once more to return to the normal display.

•Reveal mode

You can display concealed teletext information (e.g. Answer to puzzles or riddles etc.) by pressing ? button. Press ? button again to remove the information from the display.

•Subpage

Some teletext may contain several sub-pages which are automatically paged in a certain cycle by the TV station.

1.Yon can enter into a certain sub page by pressing the button directly and select the page number with number buttons. Enter the sub page number (e.g. 0003) for the third sub page.

2.Press the button again to exit the sub page mode.

3.Press the button to return to the normal TV mode.

•Color buttons (Red, Green, Yellow and blue)

Press these buttons to access directly to the corresponding color pages displayed at the lower part of the teletext screen.

23

Troubleshooting Guide

Troubleshooting

Before contact the service technician, perform the following simple checks. If any program still persists, unplug the TV and calling for serving.

	PROBLEM		POSSIBLE SOLUTION
			- Check whether the main plug has been connected to
			a wall let.
	No sound and picture		- Check whether you have pressed the POWER
			button on the front of TV set.
			- Check the picture contrast and brightness settings.
			- Check the volume.
	Normal picture but no		- Sound muted? Press the MUTE button.
			- Try another channel, the problem may be with the
	sound
			broadcast.
			- Are the audio cables installed properly?
			- Check to see if there any object between the product
			and remote control Causing obstruction.
	The remote control does		- Are batteries installed with correct polarity (+ to +,
	not work		- to -)?
			- Correct remote operating mode set: TV, VCR etc.?
			- Install new batteries
	Power is suddenly turned		- Is the sleep timer set?
			- Check the power control settings. Power interrupted.
	off
			- No broadcast on station tuned with auto activated.
	Picture appears slowly		- This is normal, the image is muted during the
			product startup process. Please contact your service
	after switching on		center, if the picture has not appeared after five
			minutes.
			- Adjust the color in menu option.
			- Keep a sufficient distance between the product and
	No or poor color or poor		the VCR.
			- Try another channel, the problem may be with the
	picture		broadcast.
			- Are the VIDEO cables installed properly?
			- Activate the any function to restore the brightness of
			the picture.
	Horizontal/vertical bars or		- Check for local interference such as an electrical
	picture shaking		appliance or power tool.
			- Station or cable product experiencing problems.
	Poor reception on some		Tune to another station.
			- Station signal is weak, reorient antenna to receive
	channels
			weaker station.
			- Check for sources of possible interference.
	Lines or streaks in		- Check the antenna (Change the direction of the
	pictures		antenna).
	No output from one of the		- Adjust balance in menu option.
	speakers

24

Troubleshooting Guide

NOTE: There is a problem in VGA mode (Only VGA mode applied).

	PROBLEM	POSSIBLE SOLUTION
		- Adjust resolution, horizontal frequency, or vertical
		frequency.
	The signal is out of range.	- Check it whether the signal cable is connected or
		loose.
		- Check the input source.
	Vertical bar or stripe on	- Work the auto configure or adjust clock, phase, or
	back ground & Horizontal
		H/V position.
	Noise & Incorrect position.
	Screen color is unstable or	- Check the signal cable.
	single color.	- Reinstall the PC video card.

Maintenance

Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the screen

1.Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then used it to wipe the screen.

2.Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

Cleaning the cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth.

Extended Absence

If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.

Disposal of old electrical appliances

The European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must

not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human

health and the environment.

The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.

Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

25

Obsah	CZ
Varování....................................................................................................	1
Bezpečnostní pokyny ..............................................................................	3
Začínáme ..................................................................................................	5
Používání dálkového ovladače...............................................................	5
Vkládání baterií do dálkového ovladače.................................................	5
Výměna baterií …………...........………..…………......................….…...5
Připojení a nastavení ...............................................................................	6
Instalace kabelů......................................................................................	6
Dálkové ovládání......................................................................................	7
Základní funkce........................................................................................	9
STRUČNÝ NÁVOD K POUŽITÍ..............................................................	9
Zapnutí a vypnutí televize.....................................................................	10
Výběr programu....................................................................................	10
Nastavení hlasitosti ..............................................................................	10
Změna zdroje vstupního signálu...........................................................	10
Funkce menu..........................................................................................	11
Jak procházet menu .............................................................................	11
Menu Kanál ..........................................................................................	11
Menu Obraz..........................................................................................	15
Menu Zvuk............................................................................................	15
Menu ČAS ............................................................................................	16
Menu VOLBY........................................................................................	16
Menu Zámek ........................................................................................	18
Používání režimu DMP.........................................................................	19
MHEG5.................................................................................................	21
Důležitá specifická tlačítka....................................................................	22
PROGRAMME GUIDE ........................................................................	22
.....................................................................................	22
SEZN. KANÁLŮ
Seznamu oblíbených.............................................................................22
Teletext ...................................................................................................	23
Používání teletextu...............................................................................	23
Řešení problémů....................................................................................	24
Odstraňování problémů........................................................................	24
Údržba..................................................................................................	25

Varování

POZOR

RIZIKO ÚRAZU ELEKTRICKÝM

PROUDEM NEOTVÍRAT

UPOZORNĚNÍ:

CHCETE-LI SNÍŽIT RIZIKO ÚRAZU ELEKTRICKÝM PROUDEM, NEOTVÍREJTE KRYT (NEBO ZADNÍ PANEL PŘÍSTROJE). UVNITŘ NEJSOU ŽÁDNÉ KOMPONENTY, KTERÉ BY MOHL UŽIVATEL SÁM OPRAVIT. VŽDY SE OBRAŤTE NA VYŠKOLENÉ ZAMĚSTNANCE SERVISU.

Symbol blesku se šipkou v rovnoramenném trojúhelníku má varovat uživatele před neizolovaným “nebezpečným napětím” uvnitř přístroje, které může být dostatečně vysoké, aby osobám způsobilo úraz elektrickým proudem.

Vykřičník v rovnostranném trojúhelníku má informovat uživatele o tom, že v literatuře přiložené k přístroji se nachází mnoho důležitých pokynů pro jeho provoz a údržbu (případně servis).

DŮLEŽITÉ INFORMACE

Zařízení vytváří, používá a může vyzařovat vysokofrekvenční energii a, pokud není instalováno a používáno podle pokynů, může být příčinou škodlivého rušení radiokomunikace. Neexistuje však záruka, že se rušení v určité instalaci neobjeví. Pokud zařízení způsobuje škodlivé rušení příjmu radiových a televizních signálů, což se dá určit vypnutím a zapnutím přístroje, doporučuje se uživateli, aby se pokusil odstranit rušení jedním nebo několika z těchto opatření:

-Přemístěním antény

-Zvětšením odstupu mezi zařízením a přijímačem

-Zapojením zařízení do zásuvky jiného obvodu, než je obvod, do kterého je přijímač zapojen

-Obraťte se na prodejce nebo zkušeného radiotechnika nebo televizního technika a požádejte ho o pomoc

Veškeré změny nebo modifikace, které strana odpovědná za shodu s předpisy výslovně neschválila, mohou zrušit platnost oprávnění uživatele zařízení provozovat.

UPOZORNĚNÍ

Nepokoušejte se žádným způsobem modifikovat tento výrobek bez písemného oprávnění dodavatele. Neoprávněné modifikace mohou zrušit platnost oprávnění uživatele provozovat tento výrobek.

Nedoporučuje se ponechávat na obrazovce zobrazený statický obraz příliš dlouho. Totéž platí o zobrazování neobyčejně jasných obrazů na obrazovce.

1

Varování

VAROVÁNÍ

Chcete-li snížit riziko požáru nebo úrazu elektrickým pouzdrem, nevystavujte přístroj působení deště nebo vlhka.

Nepoužívejte přístroj v tropickém podnebí.

Větrací otvory nesmějí být zakryty takovými předměty jako noviny, ubrusy, záclony atd., protože tím se zabraňuje nezbytnému větrání.

Nenechte na přístroj kapat vodu, nedovolte, aby do něj natekla voda a nestavte na něj žádné předměty naplněné tekutinou jako např. vázy s květinami. Nezapomínejte na ekologickou likvidaci baterie. Nevyhazujte baterie do směsného odpadu v popelnicích. V případě potřeby můžete kvůli ochraně životního prostředí kontaktovat svého prodejce.

Ponechte okolo svého přístroje volný prostor (5 cm) umožňující dostatečné větrání. (Minimální vzdálenost okolo přístroje umožňující dostatečné větrání.) Nestavte na přístroj zdroje přímého plamene jako např. hořící svíčky. Chcete-li zabránit rozšíření ohně, nikdy se k tomuto výrobku nepřibližujte se svíčkami nebo jinými zdroji otevřeného plamene.

Elektrostatický výboj může způsobit poškození zařízení. Lze manuálně obnovit vypnutím napájení a jeho opětovným zapnutím.

POZOR při zapojování napájecí sňůry

U většiny přístrojů se doporučuje, aby byly zapojeny do předem určeného obvodu, tj. do obvodu s jedinou zásuvkou, který bude napájet pouze tento přístroj a nebude mít žádné další vývody nebo větvení.

Zásuvky nepřetěžujte. Přetížené, uvolněné nebo poškozené zásuvky, prodlužovací kabel nebo napájecí šňůry s roztřepeným opletením nebo poškozenou či popraskanou izolací jsou nebezpečné. Libovolná výše uvedená závada může být příčinou úrazu elektrickým proudem nebo může způsobit požár. Pravidelně kontrolujte napájecí šňůru vašeho přístroje, a pokud jeho vzhled ukazuje na poškození nebo degradaci materiálu, vytáhněte ji ze zásuvky, přestaňte používat přístroj a nechte šňůru vyměnit za přesně stejnou novou šňůru pověřeným pracovníkem servisu. Chraňte napájecí šňůru před fyzickým nebo mechanickým poškozením. Jedná např. o její překroucení, zauzlení, smáčknutí, přivření do dveří nebo chození po ní. Dávejte také velký pozor na zásuvky, nástěnné vývody a místo, kde šňůra vstupuje do přístroje.

Zásuvka zapojená do SÍTĚ se používá k odpojení zařízení a zůstává připravena k použití.

Přístroj bude připojen k zásuvce elektrické sítě kabelem s ochranným uzemněním.

Obrázky a kresby v této uživatelské příručce jsou uvedeny pouze pro porovnání

a mohou se od aktuálního vzhledu výrobku lišit. Design a specifikace výrobku mohou být změněny bez předchozího oznámení.

2