Chaney Instrument 00595XTX2 Users Manual

The ACURITE® professional wireless weather station comes complete with the following
items:

1. Main unit with foot stand for desktop use

2. Wireless Thermo-Hygrometer & mounting bracket

3. Wireless Wind speed sensor & mounting bracket

4. Instruction Manual

5. Quick Start Guide

6. Mounting screws & wall anchors

TOOLS NEEDED:

• Philips type screwdriver: for optional surface mounting of the wireless sensor / brackets.

1 2

QUICK

STA RT

4 5 6

3

OVERVIEW OF FEATURES

WEATHER STATION MAIN UNIT:
The main unit measures the indoor environment temperature and humidity and receives
weather and time data from the two outdoor wireless sensors. The following sensors send
data back to the main unit:

1. Wireless Thermo-Hygrometer/Atomic Clock Sensor

2. Wireless Wind Sensor

The wireless weather station receives the wireless sensor data a number of times each
minute, updating you with the latest and most accurate weather information on the large,
easy-to-read LCD display, using icons and trend indicators. Enjoy using the weather station
either on the wall, using the hanging slot by fastening with a nail or provided screw, or on a
desktop, using the included snap-on foot stand.

The professional wireless weather station is composed of the following features:

• Displays the NIST (National Institute of Standards and Technology) WWVB Radio Controlled

time and date

•

Weather data, with programmable alarms for certain weather conditions, and records all minimum

and maximum values

• Indoor/outdoor temperature in either Fahrenheit or Celsius (user selectable)

• Indoor/outdoor relative humidity

• Air pressure reading in Hg or hPa

• Weather forecast with weather icons and trend indicators

• Wind speed and wind direction display with LCD compass

• Wind chill temperature display

• Heat index temperature display

• Dew point temperature display

• Time, temperature and storm alarms

• Buttons for use: MAX (+), MIN (-), DISPLAY (daily record), CLEAR, SET-UP
(on/off/record), ALARM, CHANNEL (off/wave), SNOOZE (alarm off)

NIST WWVB RADIO CONTROLLED ATOMIC SIGNAL DESCRIPTION:

The National Institute of Standards and Technology government operated WWVB atomic
radio signal, located in Fort Collins, Colorado, is the most accurate radio signal, used by

television, radio and military for the most split-second time and date information. The time
and date display on this weather station is based on the signal provided by the atomic clock
in Colorado.

WIRELESS THERMO-HYGROMETER ATOMIC CLOCK SENSOR:

The thermo-hygrometer atomic clock sensor measures the outdoor temperature and relative
humidity. It also includes the radio controlled atomic clock transmitter, which receives data

from the atomic clock in Fort Collins, Colorado, and then sends the received data back to the

main unit display. The data is sent by a 433MHz radio controlled wireless transmission.
Transmission can be received up to 100 feet away in an unobstructed open area.

WIRELESS WIND SPEED SENSOR: The wind sensor measures wind speed and wind
direction and transmits this information to the main unit display. The data is sent by a
433MHz radio controlled wireless transmission. Transmission can be received up to 100 feet
away in an open area.

GETTING STARTED

MOUNTING AND PLACEMENT CONSIDERATIONS:

The wireless transmission distance from the thermo-hygrometer sensor and wind speed sensor
to the main unit in open space under ideal conditions is 100ft. Although the signal transmission
may travel through solid surfaces or objects, try to place the wireless sensors and main unit in a
location with minimal obstructions. The following points should be avoided if possible.

• High density of large trees.

• High radio frequency areas.

• Low-E Glass.

• Thick concrete, stone or brick.

• The main unit, thermo-hygrometer and wind speed sensors should not be mounted to

metal surfaces as this can reduce range of transmission.

• Prior to drilling mounting holes or permanently affixing any of the units, please ensure

the main unit con receive the signal from the remote sensors in the desired location.

• For best reception of the signal from the atomic clock in Fort Collins, Colorado, place the

sensor in a location with a direction towards Colorado.

• The WWVB signal will be obtained easiest in the nighttime hours when the signal is the

strongest.

MOUNTING INSTRUCTIONS

MAIN UNIT:

The included foot mount can be attached to
the bottom of the main unit for easy placement
on any flat surface. Alternatively, the main
unit can be wall mounted in the desired
location by using the hang hole on the back of
the unit.

WIRELESS THERMO-HYGROMEMTER SENSOR:

The best place to mount the thermo­hygrometer sensor is in a location out of direct
sunlight and protected by extreme weather
conditions, such as under the extension of the
home roof, under a covered patio or deck.
Mount the bracket that the thermo­hygrometer sensor will set in at about eye level
by using the four included screws. Once the
bracket has been properly affixed in the
desired location, place the sensor in the
bracket holder. The thermo-hygrometer
wireless sensor may also be mounted on a
pole; which is outlined in the section

“OPTIONAL POLE MOUNTING.”

Mount With
Arrow Pointing Up

MOUNTING THE WIRELESS WIND
SPEED AND WIND DIRECTION
SENSOR:

Before permanently mounting the wind
speed bracket, make sure that the
wind-fan and wind-vane can rotate freely
without any disruption. Also note that

the wind speed sensor bracket arm
must be pointing north. The wind speed

sensor should be positioned to allow the
wind to flow around the sensor
unhindered from all directions for the
most accurate and correct readings.

OPTIONAL POLE MOUNTING:

Both sensors are designed to mount in
two ways, either to flat surfaces like wood
posts, or to 3/4” schedule 40 PVC pipe
(the outside dimension of the pipe
actually measures approximately 1, 1/16”).
The pipe mounting method is often
referred to in these instructions.

BATTERIES (not included)

NOTE: Do not install batteries in any of the units until you have read through the initial
set-up steps in their entirety.

BATTERY TYPE:

INDOOR UNIT: “AA” (3) alkaline type batteries can be used for the indoor unit.
WIRELESS OUTDOOR UNITS: It is recommended that LITHIUM type “AA” batteries be used
in any outdoor units when the temperature drops below -4ºF. Alkaline batteries may freeze
at very low temperatures and will fail to provide adequate power to the wireless units.

MAIN UNIT BATTERY REPLACEMENT:

When the low battery indicator icon becomes present, it is recommended that you change
the batteries. Replace only with the same or equivalent type of fresh alkaline batteries.

BATTERY INSTALLATION:

For the first installation, insert the batteries into the two WIRELESS SENSORS FIRST and
then into the main unit.

Thermo-Hygrometer Sensor: (See illustration next page) Rotate and pull the top casing
from the bottom cone by turning the unit upside down and rotating counter-clock wise
until casing pulls apart. Insert 2 fresh “AA” batteries (batteries not included). Replace
the battery compartment cover and rotate the top back into the bottom piece.

The ideal mounting scenario would be for
the wireless thermo-hygrometer to be
mounted on the north side of the building
and for the wind sensor to be mounted
well away from the building and high in the
air. Please test the wireless signal range
before permanently mounting.

Since PVC pipe is somewhat flexible, if a
tall wind sensor mast is being erected, a
larger diameter PVC pipe should be used
for the base with a reducer fitting placed
at the top.

Plastic pipes used for mounting are
non-conductive and reduce the likelihood
of lightening strikes.

Wind Sensor: (See illustration next page) Twist off the top from the bottom and open the
battery cover located on the bottom of the sensor. Insert 2 fresh “AA” batteries.
(Batteries not included). Replace battery door cover by putting battery cover on half way
and then sliding into place. Twist on the top to the bottom piece.

Main Unit: Open the battery cover located on the back of the unit and insert 3 fresh “AA”
batteries. (Batteries not included). Replace battery door cover.

NOTE: When reinstalling the batteries while holding down the “CLEAR” button, all user
settings will be cleared and the unit will set back to the factory default settings. If no
button is pushed during battery replacement, the last record and user settings will be
saved.

NOTE: When installing batteries, always install according to the polarity indicated in the
battery compartment ( + to + and - to - ).

LOW BATTERY INDICATOR: Low Battery Battery O.K.

Low battery indicator is displayed on the main unit for the main unit and all wireless
sensors. When replacing the batteries, please follow the battery installation procedure as
mentioned in this instruction manual. When installing or replacing batteries do not mix
battery types or old batteries with new batteries.

BATTERY REPLACEMENT:

When the low battery indicator icon becomes present, it is recommended that you change
the batteries. Replace only with the same or equivalent type of fresh alkaline batteries. This
method of battery replacement ensures there will be no loss in MIN/MAX and history data.
However, if main unit or sensors have remained without batteries for an extended period of
time, the main unit will lose the MIN/MAX and all weather data recordings and will have to be
synchronized again.