Features & Benets ....................................................................................................................................................................................................................3
Performance, Capacities and Specications .....................................................................................................................................................................5
Replacement Parts by InterLink™ .........................................................................................................................................................................................7
MEA Accepted
We have made a commitment to customer needs, innovation and
environmental stewardship and have dedicated ourselves to delivering
energy-ecient choices that reduce costs, improve bottom lines and
enhance equipment performance and service life. Look for the Energy
Solutions® logo to identify other products and options that can help you
save money and energy.
(on evaporator
section w/
PSC motors on
condensing units
section)
Shaded Pole
H
motors
or
(on evaporator and
E
condensing unit
sections)
2
Page 3
FEATURES AND BENEFITS
The PRO3 Top Mount packaged refrigeration systems combine evaporator and condensing unit into one unit —
simplifying installation and reducing refrigerant charge, which saves time, money and energy. Not only that, it’s
environmentally friendly.
The PRO3 Top Mount is designed to maximize storage area inside a cooler or freezer and is ideal for small- to
medium-sized restaurant and convenience store applications where holding temperature is the primary goal.
If greater pull-down capacity is required, see the PRO3 Side Mount packaged refrigeration system (model PST).
EASE OF INSTALLATION AND SERVICE
Installation takes a fraction of the time required for a split
•
system: no piping or loose components to install, refrigerant is
pre-charged at factory and a eld superheat adjustment is not
required (see installation manual for more information)
No drain line required: indoor models come with a
•
condensate evaporation pan
Flexible design allows for multiple installation methods:
•
optimized for indoor use, but outdoor models available with
weatherhood installed. Outdoor models also come with:
crankcase heater, drain line heater and fan-cycling for head
pressure control
Maximizes storage area in a cooler or freezer: evaporator grill
•
mounts ush on a standard 4" or a recessed 5 1/2" ceiling panel
EASE OF USE
System is factory-assembled, evacuated, charged, run-tested
•
and wired; no additional components or refrigerant charging
required; most models come with a 26" power cord ready
to plug-in
Controls preset for typical applications: +35° F for coolers, -10° F, for
•
freezers and are easy to adjust (019L6 set for 0° F)
ENERGY EFFICIENT | ENVIRONMENTALLY FRIENDLY
Energy Solutions® energy-ecient motors from InterLink™
•
Commercial Refrigeration Parts:
PSC motors optional in both condensing unit and
•
evaporator section
EC motors optional in evaporator section only
•
Reduced refrigerant charge: system uses approximately
•
10 percent* of refrigerant required for a comparable
split system
Most indoor PRO3 Top Mount
systems come standard with a 26"
power cord and 3-prong electrical
plug for quick installation and
start-up which may eliminate
the need for a eld installed
disconnect. See the data tables
in this brochure for electrical
receptacle specications.
The PRO3 Top Mount
evaporator grill sits
ush in a standard 4"
thick ceiling panel.
RELIABLE | DURABLE
System is fully-assembled and quality-tested at the factory
•
Electronic control provides accurate temperature control
•
Liquid-line lter drier (medium and large cabinet only)
•
Two-year parts warranty
•
* Results may vary. Estimate based on a typical 25-foot refrigerant line length.
MEA Accepted
PRO3 Top Mount systems
are UL-listed in the United
States and Canada
3
Page 4
NEW EC MOTORS FOR PRO3 PACKAGED REFRIGERATION SYSTEMS
Introducing the most-energy ecient motor available for packaged refrigeration systems. Choosing energyecient motors for your packaged systems can provide signicant energy savings and lower operational costs.
Additionally, because these motors can help reduce heat load (and system run-time), they can improve the
reliability and longevity of refrigeration equipment.
Electronically Commutated (EC) motors
even further improve energy eciency and equipment reliability. EC
motors by InterLink™ are up to 75% ecient – that’s a 51-59% increase over shaded pole motors and a 30-35%
increase over PSC motors. As with PSC motors, you save money both directly from a decrease in motor watts and
also from a reduction of heat gain into the refrigerated space.
Permanent Split Capacitor (PSC) motors can signicantly lower your energy costs. PSC motors average 30-35%
higher eciency than shaded pole motors and oer dual energy savings by reducing motor watts and heat gain
into the refrigerated space.
*T For Outdoor, N for Indoor. Plug Supplied on Indoor models only. See dimensions page 6.
Plug
Supplied
Matching
NEMA
Receptacle
Dimensions
Figure
Approximate Net
Weight
lbs.kg
5
Page 6
DIMENSIONS
Figure A Small Cabinet Design (indoor only)
Figure B Medium Cabinet Design
*
- 21.5" (54.61 cm) on outdoor models with weatherhood
*
Figure C Large Cabinet Design
*
- 23.5" (59.69 cm) on outdoor models with weatherhood
*
6
Page 7
Evaporator Box Top
Commercial Refrigeration Parts
Evaporator Fan Motor
Condensing Unit Wrapper
Condenser Fan Motor
Right source. Right parts. Right now.
InterLink is your link to a complete line of dependable and certied commercial refrigeration parts,
accessories and innovative electronic controls for all Chandler equipment. At InterLink, we provide our
wholesalers with a comprehensive selection of product solutions and innovative technologies for the
installed customer base. And every product is built to ensure the same high performance standards
with which all Chandler brands are built — backed by a dedicated team to serve every customer need,
delivering at the best lead times in the industry.
Dependable. Versatile. Courteous.
Finally, one simple source for all your replacement needs
from a name you can trust.
*Kits include control, sensors, mounting hardware and instructions.
**PSC motor option (H designation on end of model name): part 25307801=25308601, part 25307701=25308501, part 25303201=25399201, part 25300101=25308501. Contact InterLink Parts at 800-686-7278.
213004011 1 1 1 1 1 1 1
289165011
289162011 1 1 1 1 1 1
289163011 1 1 1
898147011 1 1 1 1 1 1
898146011 1 1 1 1 1 1
PTT069L6C
7
Page 8
For more information on Chandler products, contact
your Chandler Sales Representative or visit us at
www.chandlerref.com.
A Brand of Heatcraft Refrigeration Products LLC
2175 West Park Place Blvd. • Stone Mountain, GA 30087
800.321.1881 • FAX 770.465.5990
www.chandlerref.com
Since product improvement is a continuing ef for t, we reserve the right to make changes in specifications without notice.
CH- PTM TB 0108 | version 0 00
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.