Champsolution BL5302, BL7302, BL7305 Quick Installation Manual

Outdoor Motorized Bullet Camera

Quick Installation Guide

8608586340020

Quick Installation Guide

Please follow the installation steps below to set up your Motorized Bullet IP Camera.
Check the package contents against the list below. See P.1
Physical overview. See P.2
I/O Terminal Block Circuit. See P.3
I/O Terminal Block Pin Definition. See P.3
LED Indicator Definition. See P.4
Power mode. See P.4
Install the hardware and connect all cables. See P.5
Microsoft OS: Use the software CD to install Camera Installation Tool. See P.8
Access the IP Camera using Camera Installation Tool. See P.8
Mac OS using Safari Broswer. See P.11
Lighting environment. See P.11
Change the Web Interface into your preferred language. See P.12

Package Contents

Camera Outdoor Motorized Bullet Camera
Quick Installation Guide Brief product information and quick installation
Accessory Sun shield and screws

Wall mount bracket
Metal plate for wall mount bracket
Screw pack for wall and ceiling mounting
Alignment sticker
Body adapter
Wrench for front & back cover
Waterproof Connector
Moisture Absorber
Foam tape
2 pin terminal blocks for power
Cat 5e Female Coupler

Software

The following software and information are available online:

- Camera Bundle Software

- Camera Installation Tool

- User manuals
Please go download fromhttp://www.champsolution.com/DownloadMainpage.php

Physical overview

－

Front －

Warning:
The IR LED is classified as class 3B laser IR. It’s hazardous and harmful if the eye is
exposed directly. Please don’t look straight at the LEDs during operation.

－

Rear －

Light Sensor

Lens

IR LED

SD card/ Network Link

status indicator

Video out

Reset

I/O Terminal Block:
1: Ground,

2: +12VDC,
3: Audio in,

4: Audio out,
5: Digital Output 1,

6: Digital Output 2,
7: Digital Input 1,

8: Digital Input 2,
9: RS-485+,

10: RS-485­Power status indicator

NTSC/ PAL switch

SD card slot

DC 12V Power

Smart Focus control

2

I/O Terminal Block Circuit

I/O Terminal Block Pin Definition

PIN Definition Description Max. V/A

1 Ground ­2 + 12VDC

12V DC

1.2 W
3 Audio In Unbalanced, 1.4Vp-p, 1Vrms, terminal block ­4 Audio Out Unbalanced, 1.4Vp-p, 1Vrms, terminal block -

5 Digital Output 1

Uses an NPN transistor with the emitter
connected to the GND pin. If used with an
external relay, a diode must be connected in
parallel with the load for protection against

voltage transients.

100 mA

24V

6 Digital Output 2

Uses an NPN transistor with the emitter
connected to the GND pin. If used with an
external relay, a diode must be connected in
parallel with the load for protection against

voltage transients.

100 mA

24V

7 Digital Input 1

Connected to GND to activate, or leave
floating (or unconnected) to deactivate.

30V DC

8 Digital Input 2

Connected to GND to activate, or leave
floating (or unconnected) to deactivate.

30V DC

9 RS-485 + -

10 RS-485 - -

3

LED Indicator

LED Color Indication

Network

Blue

Steady blue for Network link

Flash blue while Network activity

Power

Red Steady red for booting up process

Blue Steady blue for booting up completion

Unlit

when reset button pressed for at least 5 sec.

to factory default

SD Card Yellow

Steady yellow means SD card ready

Flashes yellow while accessing SD card

Power Mode

PoE

Mode

at

Power

Requirement

PoE (IEEE802.3at) with Class 4

Power

Consumption

3.3 W, without IR/ Heater/ Fan

11.4 W, with max . I R on

12.8 W, wit h ma x. IR and Fan on

7.9 W, with max. Heater and Fan on

4.7 W, with max. Fan on

15.9 W, with max. IR/ Heater/ Fan

af

Power

Requirement

PoE (IEEE802.3af) with Class 3
Note: While IR on, Heater and Fan will be disabled.

Power

Consumption

3.6 W, without IR/ Heater/ Fan

11.7 W, with max. IR on

Adaptor

Mode

Power

Requirement

12V/1.5A Adaptor

Power

Consumption

3.5 W, without IR/ Heater/ Fan

11.9 W, with max . I R on

13.2 W, wit h ma x. IR and Fan on

7.8 W, with max. Heater and Fan on

4.9 W, with max. Fan on

15.9 W, with max. IR/ Heater/ Fan
Note: Heater and Fan will be activated while the inner tempara ture drops under 5℃ and
will be inactived while it above 10℃. F an will be actived while the inner temparature above
50℃ and will be inactived while it drops unde r 45℃.

4

Install the hardware and connect all cables

A. Hardware installation

a. Assembling sun shield and camera with two supplied screws (M5*6L).
Note: Please mov e the sun shield to secure the first screw on the fourth scale. (See f igure

1)

b. Use T25 wrench to loosen the back cover.
c. Take out the screw plug and change to M12 waterproof connector. Insert all cables

(power cord/ DIDO/ video out) into the connector.

d. Feed all cables to the back manual plate and connect them to the specific sockets then

secure waterproof connector tightly.

e. Attach the foam tape and moisture absorber on the back cover then secure the back

cover back. (Please change a new moisture absorber if open the front/ back covers
afterwards.)

f. Feed all cables through adapter and wall mount brack et if you use the supplied bracket,

or let the cable through out the hole on right side of adapter if you use standard br acket.
(Please see B. Two way bracket installing.) Then secure the screws (M3*12L) by

2.5mm Allen wrench.

Figure 1

5

B. Two ways bracket installation

a. Use the supplied bracke RJ45, power, DIDO, video out cables can be fed through the

supplied adapter and bracket with cable management protected installation. (See figure

1)

b. Use standard bracket

Through our supplied adapter, there’s alternatived to use your selected standard
bracket. Cables will be passed thr ough the right side hole of adapter. (See figure 2)

C. Connect Ground wire

Connect the ground wire to the IP camera’s adapter and secure with supplied ground
screw.

Figure 1

Figure 2

6

D. Wall mounting and Ceiling mounting

a. Attached the alignment sticker to the wall. Drill five holes into the wall, which four for screws and one

for cable. Then hammer the supplied plastic anchors into the screw holes and secure the mounting

plate by 5mm Allen wrench with supplied screws (T1/4”*32).

b. Hang the wall mount bracket on the mounting plate and fix it with the supplied screws.
c. Adjust the angle of the wall mount bracket by 6mm Allen wrench to aim the shooting area.

E. Connect all cables

a. Without Power over Ethernet (Po E ) c onnection

1. Connect the power adaptor to the IP Camera.

2. Using a standard RJ-45 network cable,
connect the
IP Camera to a normal Hub/ Switch/ R outer.

b. Power over Ethernet (PoE)

Using a standard RJ-45 network cable, connect the
IP Camera to a PoE-enabled Hub/ Switch/ Router.

7

Microsoft OS: Go Website download Camera Installation Tool

Please go http://www.champsolution.com/DownloadMainpage.php download “Camera
Installation Tool”. Andfollow the installation process to complete the installation.

Access the IP Camera using Camera Installation Tool

1. Please check two settings before using Camera Installation Tool

2. Click the Camera Installation Tool Icon on your desktop. The main page will show up
listing all active camera and video server devices. Select the relevant IP camera from
the list and double click to link to IE.

8

a. Browser’s Internet Properties → Security

→

Default Level

b. Browser’s Internet Properties → Privacy

→ Uncheck

Pop-up Blocker

4. When accessing the IP Camera for the first time, an information bar pops on the screen:

This website wants to install the following add-on: ‘AxvideoView.cab’.

9

3. Enter your Username and Password
to login to the IP Camera.

(Default is admin / admin)

5. Click the information bar, and select Install ActiveX control.

6. Click Install.

7. Live video displays in the centre of your web browser.

10

Mac OS using Safari Browser

Lighting environment setting

The default setting of lighting environment is Auto. However, you may also select 50 or 60
Hz upon the lighting environment o f your country.
Go to “Setting > Live View > Camera Setting > Image Se tting”, select the environment
setting you wish.

2. Click

Bonjour function

and select the camera

you wish to access.

1. Select

Safari icon

,

3. Enter name and password to login to the

IP camera. (

Default is admin / admin)

4. The monitor image will be displayed in your

br ow ser.

11

Change the Web Interface into your preferred language

Use the settings screen to set the language of the Web Interface.
Go to “Setting > System > Maintenance ”.

1. Go website

http://www.champsolution.com/DownloadMainpage.php download

language pack.

2. Browse and select the preferred language and then click OK.

3. The web interface will change into your preferred language.

12

Memo

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

Memo

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..

…………………………………………………………………………………..