10006 Santa Fe Springs Road
Santa Fe Springs, CA 90670 USA
Made in China
80000
Rev 80000-20080214
Owner’s Manual and Operating Instructions
120Volt 60-70A
ARC WELDER
Table of Contents
Introduction ..................................... 1
Portable Welder ........................................ 1
This Booklet .............................................. 1
Manual Conventions ......................... 2
Safety Rules ...................................... 3
Controls and Features ....................... 4
ARC Welder .............................................. 4
Parts Included .......................................... 5
Operation ......................................... 6
Welder Location ....................................... 6
Starting the Welder .................................. 6
Striking an ARC ........................................ 6
Maintenance ..................................... 7
Welder Maintenance ................................ 7
Storage ............................................. 7
Specifications ................................... 8
Duty Cycle and Overheating ................. 8
Parts Diagram ........................................... 9
Parts List ................................................. 10
Troubleshooting .............................. 11
Warranty ........................................ 12
Warranty Qualifications ......................... 12
Repair/Replacement Warranty .............. 12
Do not return the unit to the place of
purchase .................................................. 12
Warranty Exclusions ............................... 12
Normal Wear ....................................... 12
Installation, Use and Maintenance ..... 12
Other Exclusions ................................. 12
Limits of Implied Warranty and
Consequential Damage ........................... 12
Contact Information ............................... 12
Address ................................................ 12
Customer Service ................................ 12
Technical Service ................................. 12
Notes .............................................. 13
Introduction
Introduction
Congratulations on your purchase of a
Champion Power Equipment portable
welder. CPE designs and builds welders to
strict specifications. With proper use and
maintenance, this welder will bring years of
satisfying service.
This Booklet
Every effort has been made to ensure the
accuracy and completeness of the
information in this manual. We reserve the
right to change, alter and/or improve the
product and this document at any time
without prior notice.
Portable Welder
This unit is an AC (alternating current) ARC
Welding machine. It is designed for light
duty welding (up to 3/16”).
Record the model and serial numbers as well as date and place of purchase for future reference.
Have this information available when ordering parts and when making technical or warranty
inquiries.
Champion Power Equipment Support
1-877-338-0999
Model Number
80000
Serial Number
Date of Purchase
Purchase Location
Rev 80000-20080227 1
Manual Conventions
Manual Conventions
This manual uses the following symbols to
help differentiate between different kinds of
information. The safety symbol is used with
a key word to alert you to potential hazards
in operating and owning power equipment.
Follow all safety messages to avoid or reduce
the risk of serious injury or death.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided,
minor or moderate injury.
may
result in
CAUTION
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided,
or serious injury.
will
result in death
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided,
death or serious injury.
could
result in
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided,
may
result in property damage.
NOTE
If you have questions regarding your welder, we
can help. Please call our help line at 1-877-338-
0999.
2 Rev 80000-20080227
Safety Rules
It is suggested that you have a fire extinguisher
Safety Rules
WARNING
nearby.
Do not weld on drums, tanks, or other closed
containers
Do not use welder in thermal overload condition
– prevent overheating
Read this manual thoroughly before operating
your welder. Failure to follow instructions could
result in serious injury or death.
DANGER
Breathing welding fumes can be hazardous to
your health
Keep head and face away from welding fumes.
Use enough ventilation to avoid the buildup of
gas and fumes in the immediate area. Do not
breathe in fumes.
Use of a ventilating fan may be necessary.
DANGER
Electric Shock can kill
Electric Shock can occur from wiring or welding
electrode
Do not touch electrode with bare hand.
Wear dry insulating gloves.
Do not touch live electrical parts.
Protect yourself from electric shock by insulating
yourself from work or ground.
Properly install and ground all equipment.
DANGER
Welding can cause fire or explosion.
Do not weld near flammable material.
Welding sparks can cause fires.
DANGER
ARC rays can burn eyes and skin.
Use welding helmet with correct shade of filter
lens.
Wear welders cap and safety glasses underneath
helmet. Use ear protection if welding in an area
with heavy sound reverberation.
Button shirt collar all the way up.
Wear oil-free protective clothing: leather gloves,
heavy shirt, cuff less pants, and high boots
WARNING
Hot parts
Do not touch hot parts bare handed.
Allow cooling period before adjusting gun or
torch
Use proper tools and/or wear heavy, insulated
gloves and clothing to prevent burns
WARNING
Magnetic fields can affect pacemakers.
Pacemaker wearers keep away
WARNING
Noise can damage hearing.
Wear appropriate ear protection if noise level is
high
Rev 80000-20080227 3
Controls and Features
Controls and Features
Read this owner’s manual before operating your ARC welder. Familiarize yourself with the
location and function of the controls and features. Save this manual for future reference.
ARC Welder
Carrying Handle (1)
Amperage Control (2) – Adjust to
operate with either 60 or 70 amps
Thermal Overload Indicator (3) –
Lights when duty user exceeds duty cycle.
Allow unit to cool, and reduce duty cycle
Insulated Electrode holder (4) – Holds
stick electrode
Ground clamp (5) – “work clamp” Place
clamp as close to the weld as possible
On/Off switch (6) – Power On, Power Off
4 Rev 80000-20080227
Controls and Features
Parts Included
Your 80000 ARC Welding unit ships with the following parts:
Handheld Welding Mask
Wire Brush/Slag Hammer
Rev 80000-20080227 5
Operation
Operation
Welder Location
Place on a flat surface free of vibration.
This unit may be placed on a certified
welding cart (not included) and can be set at
an angle of 10 degrees.
Place the welder in a well-ventilated area.
DO NOT place the welder near vents or
intakes where exhaust fumes could be drawn
into occupied or confined spaces. Carefully
consider wind and air currents when
positioning welder. Place the welder in a
clean, dry place.
Starting the Welder
1. Check your environment. Make sure
there are no flammable materials in
close range.
2. Plug unit into power source
3. Turn on power switch of welder.
4. Adjust welding current – use current
adjust switch.
5. Attach electrode (welding rod) to
electrode clamp.
6. Attach ground clamp to work surface (as
close to the weld as possible).
7. Welding current starts as soon as
electrode touches the workpiece.
Striking an ARC
There are two basic techniques for striking
an ARC.
1. Drag start - Drag electrode across
workpiece like striking a match; lift
electrode slightly after touching work. If
electrode sticks to workpiece, use a quick
twist to free it. If ARC goes out, electrode
was lifted to high.
2. Tap start – Bring electrode straight down
on top of workpiece; then lift slightly to start
ARC. If electrode sticks to workpiece, use a
quick twist to free it. If ARC goes out,
electrode was lifted to high.
6 Rev 80000-20080227
Maintenance
The owner/operator is responsible for all
periodic maintenance.
WARNING
Never operate a damaged or defective welder.
WARNING
Improper maintenance will void your warranty.
Maintenance and Storage
Use a soft bristle brush to remove dirt.
Use an air compressor (25 PSI) to clear dirt
and debris from the welder.
Inspect all air vents and cooling slots to
ensure that they are clean and unobstructed.
Every 3 months
Repair or replace cracked cables
Every 6 months
Vacuum or blow out inside. During heavy
service, clean out inside monthly
Welder Maintenance
Make certain that the welder is kept clean
and stored properly. Only operate the unit in
a clean, dry operating environment. DO
NOT expose the unit to extreme conditions,
excessive dust, dirt, moisture or corrosive
vapors.
CAUTION
DO NOT use a garden hose to clean the welder.
Water will enter the welder through the cooling
slots and damage the electrical connections.
Storage
1. Allow the welder to cool completely
before storage.
2. Store in a clean, dry place out of direct
sunlight.
Rev 80000-20080227 7
Specifications
Specifications
RatedInput
Voltage 120V
Phase 1
Frequency 60Hz
Current 20A
Duty Cycle and Overheating
Duty Cycle is a percentage of 10 minutes that the unit can weld at a given rated load withou t
overheating. For example a 20% duty cycle means 2 minutes welding, 8 minutes resting. If the
unit overheats, wait 15 minutes for unit to cool, reduce amperage or duty cycle when welding
resumes.
Max.Output RatedOutput
Current
DutyCycle
Voltage
MaxOutputVoltage
70A 60A
15% 20%
22.8V 22.8V
41VAC 41VAC
8 Rev 80000-20080227
Specifications
Parts Diagram
Rev 80000-20080227 9
Specifications
Parts List
No. Description Qty
1 Ground Clamp, KDC-1200 1
2 Welding Holder, KDH-1250 1
3 Welding Cable H01N2-D1 x 10mm2 1
4 Bolt M5 x 20 1
5 Nut M5 1
6 Indicator, AD-16Y-1, 230VAC, 2mA, 50/60Hz 1
7 Rubber 2
8 Screw M4 2
9 Power Switch, KCD-25, 250VAC, 25A, 50/60Hz 1
10 Rubber Mount 4
11 Bolt M5 x 18 4
12 Nut M5 4
13 Spring Washer Φ5 4
14 Steel shelf 1
15 Bolt M5 x 2 2
16 Nut M5 2
17 Fan, KDF-120 1
18 Plug, 16A 1
19 Bolt M5 x 4 4
20 Flat-Washer Φ5 8
21 Lock washer Φ5 4
22 Nut M5 4
23 Fan, Steel 1
24 Bolt M5 x 4 4
25 Flat - Washer Φ5 8
26 Spring Washer Φ5 4
27 Nut M5 4
28 Fastener, Steel 2
29 Thermal Cutout, Metal 1
30
31 Screw M4 x 10 10
32 Cover, steel 2
33 Clasp, Metal 2
34 Handle I 1
35 Handle II 1
36 Bolt M4 x 2 2
37 Flat-Washer Φ4 2
38 Flat-Washer Φ5 2
39 Nut M5 2
Transformer Included Primary Windings:
Bobbing Coil Secondary Windings
Bobbing Coil Outer Insulation Paper
Silicon-Steel Piece Core, Aluminum
1
10 Rev 80000-20080227
Troubleshooting
Troubleshooting
Problem Cause Solution
No weld output and fan is not running Power switch is OFF Switch ON
Fuse overload Reset breakers if necessary
Weld output but fan does not run Blocked fan movement Remove item that is blocking fan or
Erratic weld current Loose cable connections Clean and tighten cable connections
Erratic arc with excessive spatter Poor, damaged electrodes Use dry, properly stored electrodes
Long arc length Shorten arc length
High amperage setting Reduce amperage setting
Electrode continually sticking to work Low amperage Increase amperage
Arc length too short Increase arc length
Defective electrode Use dry, properly stored electrodes
replace fan motor
Rev 80000-20080227 11
Warranty
Warranty
CHAMPION POWER EQUIPMENT
Effective September 1, 2006. Replaces all undated
warranties and all warranties dated before September 1,
2006.
Warranty Qualifications
Champion Power Equipment (CPE) will register
this warranty upon receipt of your Warranty
Registration Card and a copy of your sales receipt
from one of CPE's retail locations as proof of
purchase.
Please submit your warranty registration and
your proof of purchase within ten (10) days of the
date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the
mechanical and electrical components will be free
of defects in material and workmanship for a
period of one (1) year from the original date of
purchase (90 days for commercial & industrial
use). Transportation charges on product
submitted for repair or replacement under this
warranty are the sole responsibility of the
purchaser. This warranty only applies to the
original purchaser and is not transferable.
Do not return the unit to the place
of purchase
Contact CPE's Technical Service and CPE will
troubleshoot any issue via phone or e-mail. If the
problem is not corrected by this method, CPE
will, at its option, authorize evaluation, repair or
replacement of the defective part or component
at a CPE Service Center. CPE will provide you
with a case number for warranty service. Please
keep it for future reference. Repairs or
replacements without prior authorization, or at
an unauthorized repair facility, will not be
covered by this warranty.
Warranty Exclusions
This warranty does not cover the following
repairs and equipment
Normal Wear
This warranty does not cover repair when normal
use has exhausted the life of a part or the
equipment as a whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labor
if this product is deemed to have been misused,
1 YEAR LIMITED WARRANTY
:
neglected, involved in an accident, abused, loaded
beyond the specifications, modified, or installed
improperly. Normal maintenance is not covered
by this warranty.
Other Exclusions
This warranty excludes:
• Cosmetic defects such as paint, decals, etc.
• Wear items.
• Accessory parts.
• Failures due to acts of God and other force
majeure events beyond the manufacturer’s
control.
• Problems caused by parts that are not original
Champion Power Equipment parts.
Limits of Implied Warranty and
Consequential Damage
Champion Power Equipment disclaims any
obligation to cover any loss of time, use of this
product, freight, or any incidental or
consequential claim by anyone from using this
product. THIS WARRANTY IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE
A unit provided as an exchange will be subject to
the warranty of the original unit. The length of
the warranty governing the exchanged unit will
remain calculated by reference to the purchase
date of the original unit.
This warranty gives you certain legal rights which
may change from state to state. Your state may
also have other rights you may be entitled to that
are not listed within this warranty.
Contact Information
Address
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Rd.
Santa Fe Springs, CA 90670
Customer Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
Fax no.: 1-562-236-9429
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
12 Rev 80000-20080227
Notes
Notes
Rev 80000-20080227 13
Loading...