Page 1
FPO Image
OWNER’S MANUAL & OPERATING INSTRUCTIONS
10006 Santa Fe Springs Road
Santa Fe Springs CA 90670
USA / 1-877-338-0999
www.championpowerequipment.com
PORTABLE GENERATOR
SAVE THESE INSTRUCTIONS
Important Safety Instructions
are included in this manual.
MADE IN CHINA
REV B46517-20110721
4000 Starting Watts / 3500 Rated Watts
B46517
MODEL NUMBER
Page 2
Have questions or need assistance?
Do not return this product to the store!
WE ARE HERE TO HELP!
Visit our website:
www.championpowerequipment.com
for more info:
• Product Info & Updates
• Frequently Asked Questions
• Tech Bulletins
• Product Registration
– or –
Call our Customer Care Team Toll-Free at:
1-877-338-0999
24/7 Tech Support: (562) 204-1188
Page 3
B46517
4000 Starting Watts / 3500 Rated Watts
PORTABLE GENERATOR
TABLE OF CONTENTS
Introduction ............................. 1
Introduction ........................... 1
Portable Power Generator .................. 1
Accessories ........................... 1
This Booklet ........................... 1
Manual Conventions. . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Rules ............................. 3
Controls and Features ...................... 5
Generator ............................. 5
Power Panel ........................... 6
Parts Included ......................... 7
Wheel Kit .......................... 7
Other ............................. 7
Assembly ............................... 8
Remove the Generator from the Shipping Carton .. 8
Install the Wheel Kit ..................... 8
Install the Support Leg ................... 8
Add Engine Oil ......................... 8
Add Fuel ............................. 9
Grounding ............................ 9
Operation .............................. 10
Generator Location ..................... 10
Grounding ........................... 10
Surge Protection ....................... 10
Starting the Engine ..................... 10
Connecting Electrical Loads ............... 11
Stopping the Engine .................... 11
Do Not Overload Generator ................ 11
Capacity .......................... 11
Power Management ................... 11
Wattage Reference Chart ................. 12
Maintenance and Storage ................... 13
Engine Maintenance .................... 13
Oil .............................. 13
Spark Plugs ........................ 13
Air Filter .......................... 13
Spark Arrester ...................... 14
Cleaning .......................... 14
Adjustments ........................ 14
Maintenance Schedule ................ 14
Generator Maintenance .................. 15
Storage ............................. 15
Generator Storage .................... 15
Specifications ........................... 16
Engine Specifications ................... 16
Generator Specifications ................. 18
Fuel ............................... 16
Oil ................................ 16
Spark Plugs .......................... 16
Valve Clearance ....................... 16
Parts Diagram ........................ 17
Parts List ............................ 18
Engine Parts Diagram ................... 19
Engine Parts List ...................... 20
Wiring Diagram ........................ 21
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . 22
Warranty .............................. 23
Warranty Qualifications .................. 23
Repair/Replacement Warranty .............. 23
Do Not Return The Unit To
The Place Of Purchase .................. 23
Warranty Exclusions .................... 23
Normal Wear ....................... 23
Installation, Use and Maintenance ........ 23
Other Exclusions ..................... 23
Limits of Implied Warranty
and Consequential Damage ............. 23
Contact Information. . . . . . . . . . . . . . . . . . . . . 23
Address ........................... 23
Customer Service .................... 23
Technical Service .................... 23
Page 4
1 REV B46517-20110721
ENGLISH B46517
Introduction
Congratulations on your purchase of a Champion
Power Equipment generator. CPE designs and builds
generators to strict specifications. With proper use and
maintenance, this generator will bring years of satisfying
service.
Portable Power Generator
This unit is a gasoline engine driven, alternating current
(AC) generator. It is designed to supply electrical power
for lighting, appliances, tools and similar equipment.
Record the model and serial numbers as well as date and place of purchase for future reference. Have this
information available when ordering parts and when making technical or warranty inquiries.
Accessories
Champion Power Equipment manufactures and sells
accessories designed to help you get the most from
your purchase. To find out more about our covers, power
cables and storm kits, please visit our web site at:
www.championpowerequipment.com
This Booklet
Every effort has been made to ensure the accuracy and
completeness of the information in this manual. We reserve
the right to change, alter and/or improve the product and
this document at any time without prior notice.
Champion Power Equipment Support
Model Number
Serial Number
Date of Purchase
Purchase Location
1-877-338-0999
B46517
For Oil Type see ‘Add Engine Oil‘ section. For Fuel Type see ‘Add Fuel‘ section.
INTRODUCTION
Page 5
REV B46517-20110721 2
B46517 ENGLISH
MANUAL CONVENTIONS
This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol
is used with a key word to alert you to potential hazards in operating and owning power equipment.
Follow all safety messages to avoid or reduce the risk of serious injury or death.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
CAUTION
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
CAUTION
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
DANGER
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
WARNING
If you have questions regarding your generator, we can
help. Please call our help line at 1-877-338-0999
NOTE
Page 6
3 REV B46517-20110721
ENGLISH B46517
SAFETY RULES
The engine exhaust from this product contains
chemicals known to the state of California to cause
cancer, birth defects, or other reproductive harm.
Read this manual thoroughly before operating your
generator. Failure to follow instructions could result
in serious injury or death.
Generator exhaust contains carbon monoxide, a
colorless, odorless, poison gas. Breathing carbon
monoxide will cause nausea, dizziness, fainting or
death. If you start to feel dizzy or weak, get to fresh
air immediately.
Operate generator outdoors only in a well ventilated
area.
DO NOT operate the generator inside any building,
including garages, basements, crawlspaces and
sheds, enclosure or compartment, including the
generator compartment of a recreational vehicle.
DO NOT allow exhaust fumes to enter a confined
area through windows, doors, vents or other
openings.
DANGER CARBON MONOXIDE: using a generator
indoors CAN KILL YOU IN MINUTES.
Rotating parts can entangle hands, feet, hair,
clothing and/or accessories.
Traumatic amputation or severe laceration can result.
Keep hands and feet away from rotating parts.
Tie up long hair and remove jewelry.
Operate equipment with guards in place.
DO NOT wear loose-fitting clothing, dangling
drawstrings or items that could become caught.
Generator produces powerful voltage.
DO NOT touch bare wires or receptacles.
DO NOT use electrical cords that are worn, damaged
or frayed.
DO NOT operate generator in wet weather.
DO NOT allow children or unqualified persons to
operate or service the generator
Use a ground fault circuit interrupter (GFCI) in damp
areas and areas containing conductive material such
as metal decking.
Use approved transfer equipment to isolate generator
from your electric utility and Notify your utility
company before connecting your generator to your
power system.
Sparks can result in fire or electrical shock.
When servicing the generator:
Disconnect the spark plug wire and place it where it
cannot contact the plug.
DO NOT check for spark with the plug removed.
Use only approved spark plug testers.
Running engines produce heat. Severe burns can
occur on contact.
Combustible material can catch fire on contact.
DO NOT touch hot surfaces.
Avoid contact with hot exhaust gases.
Allow equipment to cool before touching.
Maintain at least three feet of clearance on all sides
to ensure adequate cooling.
Maintain at least five feet of clearance from
combustible materials.
DANGER
DANGER
DANGER
WARNING
WARNING
WARNING
WARNING
Page 7
REV B46517-20110721 4
B46517 ENGLISH
SAFETY RULES
Fuel and fuel vapors are highly flammable and
extremely explosive.
Fire or explosion can cause severe burns or death.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
When adding or removing fuel:
Turn the generator off and let it cool for at least two
minutes before removing the fuel cap. Loosen the
cap slowly to relieve pressure in the tank.
Only fill or drain fuel outdoors in a well-ventilated area.
DO NOT overfill the fuel tank.
Always keep fuel away from sparks, open flames,
pilot lights, heat and other sources of ignition.
DO NOT light or smoke cigarettes.
When starting the generator:
DO NOT attempt to start a damaged generator.
Make certain that the gas cap, air filter, spark plug,
fuel lines and exhaust system are properly in place.
Allow spilled fuel to evaporate fully before
attempting to start the engine.
Make certain that the generator is resting firmly on
level ground.
When operating the generator:
DO NOT move or tip the generator during operation.
DO NOT tip the generator or allow fuel or oil to spill.
When transporting or servicing the generator:
Make certain that the fuel shutoff valve is in the off
position and the fuel tank is empty.
Disconnect the spark plug wire.
When storing the generator:
Store away from sparks, open flames, pilot lights,
heat and other sources of ignition.
Rapid retraction of the starter cord will pull hand and
arm towards the engine faster than you can let go.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
Broken bones, fractures, bruises or sprains could result.
When starting engine, pull the starter cord slowly
until resistance is felt and then pull rapidly to avoid
kickback.
DO NOT start or stop the engine with electrical
devices plugged in.
Exceeding the generator’s running capacity can
damage the generator and/or electrical devices
connected to it.
DO NOT overload the generator.
Start the generator and allow the engine to stabilize
before connecting electrical loads.
Connect electrical equipment in the off position,
and then turn them on for operation.
Turn electrical equipment off and disconnect before
stopping the generator.
DO NOT tamper with the governed speed.
DO NOT modify the generator in any way.
Improper treatment or use of the generator can
damage it, shorten its life and void your warranty.
Use the generator only for intended uses.
Operate only on level surfaces.
DO NOT expose generator to excessive moisture,
dust, or dirt.
DO NOT allow any material to block the cooling slots.
If connected devices overheat, turn them off and
disconnect them from the generator.
DO NOT use the generator if:
– Electrical output is lost
– Equipment sparks, smokes or emits flames
– Equipment vibrates excessively
Operation of this equipment may create sparks that
can start fires around dry vegetation.
A spark arrestor may be required. The operator
should contact local fire agencies for laws or
regulations relating to fire prevention requirements.
CAUTION
WARNING
WARNING
DANGER
CAUTION
Page 8
5 REV B46517-20110721
ENGLISH B46517
Read this owner’s manual before operating your generator. Familiarize yourself with the location and function of the
controls and features. Save this manual for future reference.
(1) Fuel Tank – 4.0 gallon (15.0 L) capacity fuel tank.
(2) Choke – Used to start the engine.
(3) Fuel Valve – Turn this valve to the “ON” position to
supply fuel to the engine.
(4) Air Cleaner – Protects the engine by filtering dust
and debris from the intake air.
(5) Recoil Starter – Used to start the engine.
(6) Low Oil Sensor – Senses the level of the oil in the
crankcase and shuts the engine down if the level
falls too low.
(7) Oil Filler Cap – Check and fill engine oil level.
(8) Power Panel – See “Power Panel” section.
(9) Fold Away Handle
Generator
CONTROLS AND FEATURES
1
5
3
2
4
8
7
6
9
Page 9
REV B46517-20110721 6
B46517 ENGLISH
Power Panel
CONTROLS AND FEATURES
(1) Engine Switch – Used to turn the generator on and
off.
(2) Circuit Breaker(s) – Protects the generator against
electrical overloads. Push to reset breaker.
(3) Voltmeter – Used to display alternator output
voltage.
(4) 120 Volt AC, 30 Amp Twist-Lock Receptacle
(NEMA L5-30R) –
May be used to supply electrical
power for the operation of 120 Volt AC, 30 Amp,
single phase 60 Hz electrical loads.
(5) 120 Volt AC, 30 Amp Recreational Vehicle (RV)
Receptacle (NEMA TT-30R) – May be used to
supply electrical power for the operation of 120
Volt AC, 30 Amp, single phase 60 Hz electrical
loads
.
(6) 120 Volt AC, 20 Amp Receptacle (NEMA 5-20R)
–
May be used to supply electrical power for the
operation of 120 Volt AC, 20 Amp, single phase
60 Hz electrical loads.
(7) Ground Terminal – Consult an electrician for local
grounding regulations.
2
1 3
4 5 6 7
Page 10
7 REV B46517-20110721
ENGLISH B46517
Parts Included
Your B46517 Gasoline Powered Generator ships with the
following parts:
Wheel Kit
– 8” Wheel ............................. 2
– Flange Bolt (M10x105 for Wheel) ............ 2
– Bushing .............................. 2
– Flat Washer 10 ......................... 2
– Nut (M10) ............................ 2
– Handle .............................. 1
– Flange Bolt (M8x45 for Handle) ............. 2
– Support Leg w/Vibration Mounts ............. 1
– Flange Bolt (M8x16 for Support Leg) .......... 2
– Nut (M8) ............................. 4
Spark Arrester Kit
– Spark Arrester . . . . . . . . . . . . . . . . . . . . . . . . . . 1
– Cover Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
– Screws, Lock Washers . . . . . . . . . . . . . . . . . . . . . 2
Other
– Oil Funnel ............................ . 1
– Spark Plug Socket ....................... 1
CONTROLS AND FEATURES
Page 11
REV B46517-20110721 8
B46517 ENGLISH
ASSEMBLY
Your generator requires some assembly. This unit ships
from our factory without oil. It must be properly serviced
with fuel and oil before operation.
If you have any questions regarding the assembly of your
generator, call our help line at 1-877-338-0999. Please
have your serial number and model number available.
Remove the Generator from the Shipping Carton
1. Set the shipping carton on a solid, flat surface.
2. Remove everything from the carton except the
generator.
3. Carefully cut each corner of the box from top to
bottom. Fold each side flat on the ground to provide a
surface area to install the wheel kit and support leg.
Install the Wheel Kit
You will need the following tools to install the wheels:
• 17 mm wrench OR adjustable wrench (not included)
• Socket wrench with a 16 mm socket (not included)
• Pliers (not included)
1. Before adding fuel and oil, tip the generator on it’s side.
2. Slide the M10x105 wheel bolt through the washer,
sleeve and wheel.
3. Slide the bolt through the mount point on the frame.
4. Fasten securely with the M10 nut.
5. Repeat steps 2-4 to attach the second wheel.
Install the Support Leg
1. Attach the support leg to the generator frame with
cap screws (M8x16) and nuts (M8).
2. Tip the generator slowly so that it rests on the
wheels and support leg.
The wheel kit is not intended for over-the-road use.
CAUTION
1. Place the generator on a flat, level surface.
Add Engine Oil
DO NOT attempt to crank or start the engine before
it has been properly filled with the recommended
type and amount of oil. Damage to the generator as
a result of failure to follow these instructions will
void your warranty.
CAUTION
Install the Handles
1. Place the handle over the mounting channel on the
frame.
2. Secure the handle to the frame using the two handle
bolts (M8x45).
3. Place a lock nut (M8) on the end of each bolt and
fasten securely. DO NOT over tighten the lock nuts.
The recommended oil type is 10W-30 4-cycle automotive oil.
NOTE
Page 12
9 REV B46517-20110721
ENGLISH B46517
ASSEMBLY
4. Check engine oil level daily and add as needed.
The engine is equipped with a low-oil-shutoff and
will stop when the oil level in the crankcase falls
below the threshold level.
CAUTION
Check oil often during the break-in period. Refer to the
Maintenance section for recommended service intervals.
NOTE
The generator rotor has a sealed, pre-lubricated ball
bearing that requires no additional lubrication for
the life of the bearing.
NOTE
Add Engine Oil Cont’d. Add Fuel Cont’d.
2. Remove oil fill cap/dipstick to add oil.
3. Add 0.63 qt (0.6 L) of oil and replace oil fill cap/
dipstick.
Add Fuel
1. Use clean, fresh, regular unleaded fuel with a
minimum octane rating of 85 and an ethanol content
of less than 10% by volume.
2. DO NOT mix oil with fuel.
3. Clean the area around the fuel cap.
4. Remove the fuel cap.
5. Slowly add fuel to the tank. DO NOT overfill. Allow
approximately ¼ inch of space for fuel expansion.
6. Screw on the fuel cap and wipe away any spilled fuel.
Use regular unleaded gasoline with a minimum
octane rating of 85.
DO NOT mix oil and gasoline.
Fill tank to approximately ¼ inch below the top of
the tank to allow for fuel expansion.
DO NOT fill fuel tank indoors.
DO NOT fill fuel tank when the engine is running or hot.
DO NOT overfill the fuel tank.
DO NOT light cigarettes or smoke when filling the
fuel tank.
CAUTION
Grounding
Your generator must be properly connected to an
appropriate ground to help prevent electric shock.
A ground terminal connected to the frame of the generator
has been provided on the power panel. For remote
grounding, connect of a length of heavy gauge (12 AWG
minimum) copper wire between the generator ground
terminal and a copper rod driven into the ground. We
strongly recommend that you consult with a qualified
electrician to ensure compliance with local electrical codes.
Failure to properly ground the generator can result
in electric shock.
WARNING
Page 13
REV B46517-20110721 10
B46517 ENGLISH
Generator Location
Please consult your local authority. In some areas,
generators must be registered with the local utility.
Generators used at construction sites may be subject to
additional rules and regulations.
This generator must have at least five feet of clearance
from combustible material. Leave at least three feet
of clearance on all sides of the generator to allow for
adequate cooling, maintenance and servicing.
Place the generator in a well-ventilated area. DO NOT
place the generator near vents or intakes where exhaust
fumes could be drawn into occupied or confined
spaces. Carefully consider wind and air currents when
positioning generator.
Grounding
The generator system ground connects the frame to the
ground terminals on the power panel.
The generator (stator winding) is isolated from the frame
and from the AC receptacle ground pin. Electrical devices
that require a grounded receptacle pin connection may not
function properly.
Surge Protection
Electronic devices, including computers and many
programmable appliances use components that are
designed to operate within a narrow voltage range and
may be affected by momentary voltage fluctuations.
While there is no way to prevent voltage fluctuations, you
can take steps to protect sensitive electronic equipment.
1. Install UL1449, CSA-listed, plug-in surge suppressors
on the outlets feeding your sensitive equipment.
Surge suppressors come in single- or multi-outlet
styles. They’re designed to protect against virtually
all short-duration voltage fluctuations.
Voltage fluctuation may impair the proper
functioning of sensitive electronic equipment.
CAUTION
OPERATION
Starting the Engine
1. Make certain the generator is on a flat, level surface.
2. Disconnect all electrical loads from the generator.
Never start or stop the generator with electrical
devices plugged in or turned on.
3. Turn the Fuel Valve to the “ON” position.
4. Flip the ignition switch to the “ON” position.
5. Move the choke lever to the “CHOKE” position.
6. RECOIL START: Pull the starter cord slowly until
resistance is felt and then pull rapidly
7. Do not over-choke. As as soon as engine starts, move
the choke lever to the “RUN” position.
If the engine starts but does not run make certain
that the generator is on a flat, level surface. The
engine is equipped with a low oil sensor that will
prevent the engine from running when the oil level
falls below a critical threshold.
NOTE
Keep choke lever in “Choke” position for only 1
pull of the recoil starter. After first pull, move choke
lever to the “Run” position for up to the next 3
pulls of the recoil starter. Too much choke leads to
sparkplug fouling/engine flooding due to the lack of
incoming air. This will cause the engine not to start.
NOTE
Page 14
11 REV B46517-20110721
ENGLISH B46517
Connecting Electrical Loads
1. Let the engine stabilize and warm up for a few
minutes after starting
2. Plug in and turn on the desired 120 Volt AC single
phase, 60 Hz electrical loads.
– DO NOT connect 3-phase loads to the generator.
– DO NOT connect 50 Hz loads to the generator.
– DO NOT overload the generator.
Connecting a generator to your electric utility
company’s power lines or to another power source
may be against the law. In addition this action,
if done incorrectly, could damage your generator
and appliances and could cause serious injury or
even death to you or a utility worker who may be
working on nearby power lines. If you plan to run a
portable electric generator during an outage, please
notify your electric utility company immediately
and remember to plug your appliances directly
into the generator. Do not plug the generator into
any electric outlet in your home. Doing so could
create a connection to the utility company power
lines. You are responsible for ensuring that your
generator’s electricity does not feed back into the
electric utility power lines.
If the generator will be connected to a building
electrical system, consult your local utility company
or a qualified electrician. Connections must isolate
generator power from utility power and must comply
with all applicable laws and codes.
NOTE
OPERATION
Do Not Overload Generator
Capacity
Follow these simple steps to calculate the running and
starting watts necessary for your purposes.
1. Select the electrical devices you plan on running at
the same time.
2. Total the running watts of these items. This is
the amount of power you need to keep your items
running.
3. Identify the highest starting wattage of all devices
identified in step 1. Add this number to the number
calculated in step 2. Surge wattage is the extra
burst of power needed to start some electric driven
equipment. Following the steps listed under “Power
Management” will guarantee that only one device will
be starting at a time.
Power Management
Use the following formula to convert voltage and
amperage to watts:
Volts x Amps = Watts
To prolong the life of your generator and attached
devices, follow these steps to add electrical load:
1. Start the generator with no electrical load attached
2. Allow the engine to run for several minutes to stabilize.
3. Plug in and turn on the first item. It is best to attach
the item with the largest load first.
4. Allow the engine to stabilize.
5. Plug in and turn on the next item.
6. Allow the engine to stabilize.
7. Repeat steps 5-6 for each additional item.
Never exceed the specified capacity when adding
loads to the generator.
NOTE
Stopping the Engine
1. Turn off and unplug all electrical loads. Never start
or stop the generator with electrical devices plugged
in or turned on.
2. Let the generator run at no-load for several minutes
to stabilize internal temperatures of the engine and
generator.
3. Press the ignition switch to the “OFF” position.
4. Turn the Fuel Valve to the “OFF” position.
Important: If the generator will be moved or stored
turn the Fuel Valve to the “OFF“ position and ensure
the Ignition Switch on the Power Panel is in the “OFF“
position.
Page 15
REV B46517-20110721 12
B46517 ENGLISH
OPERATION
Wattage Reference Chart
Use the chart to determine approximate wattage
requirements for your equipment.
Item
Running
Watts (A)
Starting
Watts (B)
Essentials
Light Bulb 100W 100
Refrigerator/ Freezer 1200 2400
Freezer 50 0 500
Sump Pump 600 1800
Well Pump 1 HP 2000 4000
Water Heater 4000
Security System 180
AM/ FM Radio 300
Garage Door Opener 1/2 HP 500 600
Battery Charger 12V D C 110
Heating /Cooling
Air Conditioner 12000 BTU 1700 2500
Fan 300 600
Furnace Fan 1/3 HP 1200 2000
Home Appliances
Microwave 1000W 1000
Electric Range - One Element 1500
Electric Skillet 1250
Coffee Maker 1500
Clothes Washer 1200
Entertainment
CD/ DVD Player / VCR 100
Stereo Receiver 450
Television 27” 500
PC with 15” Monitor 800
Job Site
Belt Sander 3” 1000 1500
Bench Grinder 6” 700 1500
Circular Saw 1500 1500
Compressor 1 1/2 HP 2500 2500
Edge Trimmer 500 500
Hand Drill 1/2” 1000 1000
Lawn Mower 1200 1800
Paint Sprayer 60 0 1200
Table Saw 2000 2000
Exceeding specified load capacity can result in
damage to the generator.
To determine total wattage necessary to power
a device, ADD Running Watts to Starting Watts.
(A+B). Starting watts can exceed three times the
running watts. The values in the following table are
approximate. Refer to your tool or appliance for actual
wattage consumption.
CAUTION
Page 16
13 REV B46517-20110721
ENGLISH B46517
The owner/operator is responsible for all periodic
maintenance.
Complete all scheduled maintenance in a timely manner.
Correct any issue before operating the generator.
Never operate a damaged or defective generator.
Tampering with the factory set governor will void
your warranty.
Engine Maintenance
To prevent accidental starting, remove and ground spark
plug wire before performing any service.
Oil
Change oil when the engine is warm. Refer to the oil
specifi cation to select the proper grade of oil for your
operating environment.
1. Remove the oil drain plug with a 12 mm socket and
extension.
2. Allow the oil to drain completely.
3. Replace the drain plug.
4. Remove oil fi ll cap/dipstick to add oil.
5. Add 0.63 qt (0.6 L) of oil and replace oil fi ll
cap/dipstick.
6. Dispose of used oil at an approved waste
management facility.
Air Filter
1. Remove the snap-on cover holding the air fi lter to
the assembly.
2. Remove the foam element.
3. Wash in liquid detergent and water. Squeeze
thoroughly dry in a clean cloth.
4. Saturate in clean engine oil.
5. Squeeze in a clean, absorbent cloth to remove all
excess oil.
6. Place the fi lter in the assembly.
7. Reattach the air fi lter cover and snap in place.
Spark Plugs
1. Remove the spark plug cable from the spark plug.
2. Use the spark plug tool that shipped with your
generator to remove the plug.
3. Inspect the electrode on the plug. It must be clean and
not worn to produce the spark required for ignition.
4. Make certain the spark plug gap is 0.7 - 0.8mm or
(0.028 - 0.031 in.).
5. Refer to the spark plug recommendation chart when
replacing the plug.
6. Carefully thread the plug into the engine.
7. Use the spark plug tool to fi rmly install the plug.
8. Attach the spark plug wire to the plug.
For service or parts assistance, contact our help
line at 1-877-338-0 999
NOTE
Maintenance, replacement, or repair of emission
control devices and systems may be performed
by any non-road engine repair establishment or
individual.
NOTE
WARNING
WARNING
Improper maintenance will void your warranty.
WARNING
Oil Cont’d.
0.7 - 0.8 mm
0.028 - 0.031 in.
MAINTENANCE AND STORAGE
Once oil has been added, a visual check should show
oil about 1-2 threads from running out of the fi ll hole.
If using the dipstick to check oil level, DO NOT screw
in the dipstick while checking.
NOTE
Page 17
REV B46517-20110721 14
B46517 ENGLISH
Adjustments
The air-fuel mixture is not adjustable. Tampering with
the governor can damage your generator and your
electrical devices and will void your warranty. CPE
recommends that you contact our service line at
1-877-338-0 999 for all other service and/or adjustment
needs.
Maintenance Schedule
Follow the service intervals indicated in the following
maintenance schedule.
Service your generator more frequently when operating
in adverse conditions.
Contact our helpline at 1-877-338-099 9 to locate the
nearest Champion Power Equipment certified service
dealer for your generator or engine maintenance needs.
Use a damp cloth to clean exterior surfaces of the engine.
Use a soft bristle brush to remove dirt and oil.
Use an air compressor (25 PSI) to clear dirt and debris
from the engine.
Cleaning
DO NOT spray engine with water.
CAUTION
Water can contaminate the fuel system.
Spark Arrester
1. Allow the engine to cool completely before servicing
the spark arrester.
2. Remove the two screws holding the cover plate which
retains the end of the spark arrester to the muffler.
3. Remove the spark arrester screen.
4. Carefully remove the carbon deposits from the spark
arrester screen with a wire brush.
5. Replace the spark arrester if it is damaged.
6. Position the spark arrester in the muffler and attach
with the two screws.
Failure to clean the spark arrester will result in
degraded engine performance.
CAUTION
MAINTENANCE AND STORAGE
Federal and local laws and administrative
requirements indicate when and where spark
arresters are required. When ordered, spark
arresters are required for operation of this generator
in National Forest lands. In California, this
generator must not be used on any forest- covered
land, brush-covered land, or grass- covered land
unless the engine is equipped with a spark arrester.
NOTE
*To be performed by knowledgeable, experienced owners or
Champion Power Equipment certified dealers.
Every 8 hours or daily
Check oil level
Clean around air intake and muffler
First 5 Hours
Change oil
Every 50 hours or every season
Clean air filter
Change oil if operating under heavy load or in hot environments
Every 100 hours or every season
Change oil
Clean/Adjust spark plug
Check/Adjust valve clearance *
Clean spark arre ster
Clean fuel tank and filter *
Every 3 years
Replace fuel line
Page 18
15 REV B46517-20110721
ENGLISH B46517
MAINTENANCE AND STORAGE
Generator Maintenance
Make certain that the generator is kept clean and stored
properly. Only operate the unit on a flat, level surface in
a clean, dry operating environment. DO NOT expose the
unit to extreme conditions, excessive dust, dirt, moisture
or corrosive vapors.
Storage
The generator should be started at least once every 14
days and allowed to run for at least 20 minutes. For
longer term storage, please follow these guidelines.
Generator Storage
1. Allow the engine to cool completely before storage.
2. Clean the generator according to the instructions in
the Maintenance section.
3. Turn the Fuel Valve to the “OFF” position.
4. Be sure all appliances are disconnected from the
generator. Start the engine and let it run until the
fuel in the line and the carburator is consumed and
the engine dies.
5. Add a fuel stabilizer into the fuel tank.
6. Change the oil.
7. Remove the spark plug and pour about ½ ounce
of oil into the cylinder. Crank the engine slowly to
distribute the oil and lubricate the cylinder.
8. Reattach the spark plug.
9. Store the unit in a clean, dry place out of direct
sunlight.
Use a damp cloth to clean exterior surfaces of the generator.
Use a soft bristle brush to remove dirt and oil.
Use an air compressor (25 PSI) to clear dirt and debris
from the generator.
Inspect all air vents and cooling slots to ensure that they
are clean and unobstructed.
DO NOT use a garden hose to clean the generator.
Water can enter the generator through the cooling
slots and damage the generator windings.
CAUTION
Page 19
REV B46517-20110721 16
B46517 ENGLISH
Engine Specifications
– Engine .................... 196 cc OHV CPE
Valve Clearance
– Intake: 0.13 – 0.17 mm (0.005 – 0.007 in.)
– Exhaust: 0.18 – 0.22 mm (0.007 – 0.009 in.)
Oil
Use 4-Cycle automotive oil.
Oil capacity is 0.63 qt (0.6 L).
Please reference the following chart for recommended
oil types for use in the generator.
Fuel
Fuel capacity is 4 gallons (15 L). Use regular unleaded
gasoline with a minimum octane rating of 85 and an
ethanol content of less than 10% by volume.
Generator Specifications
– Rated Wattage ................. . 3500 Watts
– Starting Wattage ................ . 4000 Watts
– AC Load ......................... . 120 V
– Phase ........................... . Single
– Frequency ........................ . 60 Hz
– Fuel Capacity ................ 4 gallons (15 L)
– Gross Weight ............. .115.7 lbs (52.5 kg)
– Net Weight ............... 106.9 lbs (48.6 kg)
– Height ................ 20.4 inches (51.8 cm)
– Width ................ 23.0 inches (58.5 cm)
– Length. . . . . . . . . . . . . . . . .24.7 inches (62.7 cm)
Spark Plugs
Recommended replacement spark plug:
– NGK BR6ES or equivalent
Make certain the spark plug gap is 0.7 – 0.8 mm or
(0.028 – 0.031 in.).
SPECIFICATIONS
Page 20
17 REV B46517-20110721
ENGLISH B46517
SPECIFICATIONS
Parts Diagram
Page 21
REV B46517-20110721 18
B46517 ENGLISH
Parts List
# Part Number Description Qty
1 GB819 M5×10 Screw M5 ×10 2
2 ST02FD-0414000 0 Fuel Meter A ssembly 1
3 ST02FD-04120000-A Fuel Tank Cap 1
4 ST02FD- 04130000 Fuel Filter 1
5 GB5789 M6× 20 Flange Bolt M6×20 4
6 ST02FD- 04100014 Washer 6.5 4
7 ST02FD- 04100010 Vibration mount 4
8 ST02FD- 04110000(Y) Fuel Tank 1
9 ST02FD- 04160000 Fuel Cock 1
10 ST168FD -1160002 Fuel Tube 1
11 ST188FD-1070006A Clip 2
12 GB5789 M6×12 Flange Bolt M6×12 8
13 GB5789 M8×20 Flange Bolt M8 ×20 3
14 ST02FD-1150100 Muffler Stay（II（ 1
15 ST02FD-1150200 Muffler Stay（I（ 1
16 ST02FD-02100010 Wiring teminal 1
17 ST02FD-021000 08 Plate Pinch 1
18 GB16674 M5×12 Flange Bolt M5 ×12 2
19 ST02FD-02100004(Y) Generator End C over 1
20 GB16674 M5×16 Flange Bolt M5×16 2
21 ST02FD-02100007-CPE AVR 1
22 GB5783 M5×16 Bolt M5×16 4
23 GB93 5 Spring Washer 5 3
24 GB97.1 5 Washer（5 3
25 ST02FD-02100009 Brush Assembly 1
26 ST02FD-02100001-2.5 Flange Bolt M6×158 4
27 GB93 6 Locking Washer 6 4
28 GB97.1 6 Washer（6 4
29 ST02FD-02100003 End Cover 1
30 ST02FD-02100002-2.5 Stator Cover 1
31 ST02FD-02120000-2.5 Stator Assembly 1
32 ST02FD-02100005-2.5 Flange Bolt M8×233 1
33 GB7244 8 Spring Washer 8 1
34 GB96 8 Washer（8 1
35 ST02FD-02110000-2.5 Rotor Assembly 1
36 ST02FD-02100012 Choke plug（A（ 1
37 ST02FD-02100011 Choke plug（B（ 1
38 ST168FD-2-01000 000 -G Engine 1
39 ST168FD-1090006 Air Cleaner stay 1
40 GB5789 M6× 8 Flange Bolt M6×8 1
41 ST168F-1100200- G Muf fler Gasket 1
42 GB848 8 Washer （8 2
43 GB7244 8 Locking Washer （8 2
44 GB6175 M8 Nut M8 2
45 ST168FD-1100000-G Muffler 1
46 ST188FD-1180121 Spark Arrester Assembly 1
47 ST188FD-1100010-88 Spark Arrester Cover 1
# Part Number Description Qty
48 GB93 5 Locking Washer （5 2
49 GB818 M5×15 Screw M5×15 2
50 GB6177 M6 Nut M6 1
51 ST02FD-02100013-2.5 Earth Wire 1
52 GB5789 M8×25 Flange boltM8 ×25 2
53 ST188FD-1743002-C Vibration mount 2
54 ST05FD- 03020301-60 Support leg (2.36in) 1
55 GB5789 M8×16 Flange Bolt M8×16 2
56 GB6177 M8 Nut M8 14
57 ST02FD-1151300C-1 Bottom rubber II 2
58 GB6182 M10 Nut M10 2
59 ST177FD-1152300 8in Wheel 2
60 ST02FD-03621001 Bush （10.5×58.5 2
61 GB96 10 Flat washer （10 2
62 GB5782 M10×105 Bolt M10×105 2
63 ST02FD-1151300D-1 Motor mount I 2
64 ST02FD-0172(F) Frame 1
65 ST02FD-03030400 (F) Muffler Cover 1
66 GB5789 M8× 45 Flange boltM8×45 2
67 ST182FD-1151110-B Handle 1
68 ST02FD-05212002 Choke plug 1
69 ST02FD-05202003 Sleeving 1
70 ST02FD-05212001 Choke plug 1
71 GB823 M5×38 Screw M5 ×38 3
72 GB848 5 Washer 5 3
73 ST02FD-05202002 Control panel cover 1
74 GB5783 M6×22 Bolt M6×22 1
75 GB97.1 6 Washer（6 2
76 GB93 6 Locking Washer（6 2
77 GB6175 M6 Nut M6 2
78 ST02FD-05010703 Flange Bolt M5×13 4
79 ST02FD-05502024 5-20R Receptacle 1
80 ST02FD-05502029 RV Receptacle 1
81 GB818 M4×14 Screw M4×14 6
82 ST02FD-05502020 L5 -30R Receptacle 1
83 ST02FD- 05602010-D Volt Meter 1
84 ST02FD- 05302001-L20
AC.20A CIRCUIT
BREAKERS
1
85 ST02FD-053020 01-L25
AC.25A CIRCUIT
BREAKERS
1
86 2A56 Control Panel 1
87 ST02FD-05702002 Ignition Switch 1
88 OV01-00000000 Voltage protector 1
89 GB6177 M4 Nut M4 5
90 GB818 M4×14 Screw M4×14 1
91 ST188FD-1020001 Rubbler sleeve 1
Page 22
19 REV B46517-20110721
ENGLISH B46517
SPECIFICATIONS
Engine Parts Diagram
Page 23
REV B46517-20110721 20
B46517 ENGLISH
# Part Number Description
Qty
1
GB5789-86-FB6- 8 Flange Bolt M6×8 5
2
ST160F-1061200 Recoil Starter Knob 1
3
ST160F-1061100 -Q Recoil Starter C over 1
4
ST160F-1061005 Recoil Starter Spring 1
5
ST160F-1061009 Recoil Starter Rope 1
6
ST160F-1061001-A Recoil Starter Reel 1
7
ST188F-1060006 Return Spring 2
8
ST188F-1060005 Starter Ratchet 2
9
GB5789-FB6-12 Flange Bolt M6×12 9
10
ST188F-1060003 Ratchet Guide 1
11
ST188F-1060004 Ratchet Guide Spring 1
12
ST188F-1060002 Ratchet Guide Bolt 1
13
ST168F-1080100-G Fan Cover 1
14
ST160F-1050010 Nut M14 1
15
ST160F-1060001 Start Hub 1
16
ST168F-1080001 Cooling Fan 1
17
ST168F-1120100 Flywheel 1
18
ST168F-1080200 Side Place II 1
19
ST168F-1030100 Oil Seal 2
20
GB5789-FB6-15 Flange Bolt M6×15 4
21
ST160F-1030003 Drain Plug Bolt 2
22
ST160F-1030004 Drain Bolt Washer 2
23
ST168F-2-1030012-G Crankcase 1
24
GB276-BB-6205-UU
Radial Ball Bearing 6205
Unsealed
2
25
ST160F-1127000 -A Oil Level Switch 1
26
ST160F-1110108 Governor Washer 1
27
ST160F-1110101 Governor Weight Holder 1
28
ST160F-1110102 Governor Weight Pin 2
29
ST160F-1110104 Governor Shaft 1
30
ST160F-1110103 Governor Holder Clip 1
31
ST160F-1110107 Governor Weight 2
32
ST160F-1110108 Governor Washer 1
33
ST160F-1110105-A Governor Cover 1
34
ST168F-2-1050001-A Crankshaft 1
35
ST168F-1030008-G Case C over Packing 1
36
ST160F-1030001-B Oil Filler Cap 1
37
ST160F-1030002 Oil Filler Cap Packing 1
38
GB5789-FB8-32 Flange Bolt M8×32 6
39
ST168F-1110005 Throttle Return Spring 1
40
ST168F-1110007 Governor Spring 1
41
ST160F-1110003 Governor Arm 1
42
GB41-N-6 Nut M6 3
43
ST160F-1110008 Lock Pin 1
44
ST160F-1110001 Governor Arm Shaft 1
45
ST168F-1110006 Governor Rod 1
46
ST160F-1110004 Governor Arm Bolt 1
47
GB5789-FB6-25 Flange Bolt M6×25 2
48
ST160F-1123000-G Ignition Coil 1
49
152FMD-1001007 Dowel Pin 10x16 2
50
GB5789-FB8-55 Flange Bolt M8×55 4
# Part Number Description
Qty
51
ST168FD-1090200-G Air Cleaner Cover 1
52
ST168FD-10900 04 Element 1
53
ST168FD-10900 03 Separator 1
54
ST168FD-10900 02 Air Cleaner Seal 1
55
ST168FD-1090100 Air Cleaner Case 1
56
ST160F-1130003-CPE Carburetor Packing 1
57
ST168F-1130001 Carburetor Insulator 1
58
ST168F-1130002-CPE Insulator Packing 1
59
ST160F-1010001 Stud Bolt M6×113 2
60
ST168F-2-1010100-G Cylinder Head 1
61
ST168F-2-1030009-G Cylinder Head Gasket 1
62
ST168F-1040002 Intake Valve 1
63
ST168F-1040006 Exhaust Valve 1
64
ST168F-2-1040013 Valve Lifter 2
65
ST168F-2-1041000 Camshaft Comp 1
66
ST168F-1030015-G D owel Pin 9×14 2
67
ST168FD-1111100 Control Assembly 1
68
GB1099-79 Key 4 ×7.5×19 1
69
ST168FD-1030007-G Crankcase Cover 1
70
ST168F-1050100 Connecting Rod Comp 1
71
ST168F-1050003 Piston Pin 1
72
ST168F-1050004 Piston Pin Clip 2
73
ST168F-2-1050005 Piston 1
74
ST168F-1050007 First Piston Ring, Chrome 1
ST168F-1050006 Second Ring Set 1
ST168F-1050200 Oil Ring Set 1
75
ST168F-1080002- G Shroud I 1
76
GB900 -SB8 -32 Stud Bolt M8×32 2
77
ST168F-1040005 Push Rod 2
78
ST168F-1040014-A Valve Oil Seal 2
79
ST168F-1040027 Pivot Bolt 2
80
ST168F-1040026 Rocker Arm Block 1
81
GB41-N-6 Nut M6 2
82
ST168F-1040023 Exhaust Rocker 1
83
ST160F-1020001 Breather Tube 1
84
ST168F-1020100-C Cylinder Head Cover 1
85
ST160F-1020002-A Head Cover Gasket 1
86
ST168F-1040024 Tappet Adjusting Bolt 2
87
ST168F-1040025 Lock Nut 2
88
ST168F-1040022 Intake Rocker 1
89
ST168F-1040021 Rocker A xis 1
90
ST160F-1040008 Valve Rotator 1
91
ST160F-1040001 Intake Valve Spring Retainer 1
92
ST160F-1040007 Exhaust Valve Spring Retainer 1
93
ST160F-1040003 Valve Spring 2
94
ST160F-1124000 Spark Plug 1
95
ST168FD-2-11310 00 Carburetor 1
96
ST168FD-1130005- CPE Packing 1
97
ST02FD-1151201A Choke Lever 1
Page 24
21 REV B46517-20110721
ENGLISH B46517
Wiring Diagram
SPECIFICATIONS
Page 25
REV B46517-20110721 22
B46517 ENGLISH
TROUBLESHOOTING
For further technical support :
Technical Service
Mon – Fri 8:30 AM – 5: 00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
Problem Cause Solution
Generator will not start No fuel Add fuel
Faulty spark plug Replace spark plug
Unit loaded during start up Remove load from unit
Generator will not start; Low oil level Fill crankcase to the proper level
Place generator on a flat, level surface
Generator starts but runs roughly Choke in the wrong position. Adjust choke.
Spark plug wire loose Attach wire to spark plug
Generator shuts down during operation Out of fuel Fill fuel tank
Low oil level Fill crankcase to the proper level. Place
generator on a flat, level surface
Generator cannot supply enough power or
overheating
Generator is overloaded Review load and adjust. See “Power
Management”
Insufficient ventilation Check for air restriction. Move to a well
ventilated area
No AC output Cable not properly connected Check all connections
Connected device is defective Replace defective device
Circuit breaker is open Reset circuit breaker
Faulty brush assembly Replace brush assembly (Service Center)
Faulty AVR (auto voltage regulator) Replace AVR (Ser vice Center)
Loose wiring Inspect and tighten wiring connections
Other Contact the help line.
Generator gallops Engine governor defective Contact the help line
Repeated circuit breaker tripping O verload Review load and adjust. See “Power
Management”
Faulty cords or device Check for damaged, bare or frayed wires.
Replace defective device
Page 26
23 REV B46517-20110721
ENGLISH B46517
WARRANTY
WARRANTY
CHAMPION POWER EQUIPMENT
2 YEAR LIMITED WARRANTY
Warranty Qualifications
Champion Power Equipment (CPE) will register this
warranty upon receipt of your Warranty Registration Card
and a copy of your sales receipt from one of CPE’s retail
locations as proof of purchase.
Please submit your warranty registration and your proof
of purchase within ten (10) days of the date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the
mechanical and electrical components will be free of
defects in material and workmanship for a period of
one year (parts and labor) and two years (parts) from
the original date of purchase (90 days (parts and
labor) and 180 days (parts) for commercial & industrial
use). Transportation charges on product submitted
for repair or replacement under this warranty are the
sole responsibility of the purchaser. This warranty only
applies to the original purchaser and is not transferable.
Do Not Return The Unit To The Place Of Purchase
Contact CPE’s Technical Service and CPE will
troubleshoot any issue via phone or e-mail. If the
problem is not corrected by this method, CPE will, at its
option, authorize evaluation, repair or replacement of the
defective part or component at a CPE Service Center.
CPE will provide you with a case number for warranty
service. Please keep it for future reference. Repairs
or replacements without prior authorization, or at an
unauthorized repair facility, will not be covered by this
warranty.
Warranty Exclusions
This warranty does not cover the following repairs and
equipment:
Normal Wear
Generators need periodic parts and service to perform well.
This warranty does not cover repair when normal use has
exhausted the life of a part or the equipment as a whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labor if this
generator is deemed to have been misused, neglected,
involved in an accident, abused, loaded beyond the
generator’s limits, modified, installed improperly or
connected incorrectly to any electrical component.
Installation, Use and Maintenance Cont’d.
Normal maintenance such as spark plugs, air filters,
adjustments, fuel system cleaning and obstruction due
to buildup is not covered by this warranty.
Other Exclusions
This warranty excludes:
– Cosmetic defects such as paint, decals, etc.
– Wear items such as filter elements, o-rings, etc.
– Accessory parts such as starting batteries, and
storage covers.
– Failures due to acts of God and other force majeure
events beyond the manufacturer’s control.
– Problems caused by parts that are not original
Champion Power Equipment parts.
This warranty does not apply to generators used for
prime power in place of a utility.
Limits of Implied Warranty and Consequential Damage
Champion Power Equipment disclaims any obligation to
cover any loss of time, use of this product, freight, or
any incidental or consequential claim by anyone from
using this generator. THIS WARRANTY IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
A unit provided as an exchange will be subject to the
warranty of the original unit. The length of the warranty
governing the exchanged unit will remain calculated by
reference to the purchase date of the original unit.
This warranty gives you certain legal rights which may
change from state to state. Your state may also have
other rights you may be entitled to that are not listed
within this warranty.
Contact Information
Address
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Rd.
Santa Fe Springs, CA 90670
www.championpowerequipment.com
Customer Service
Mon – Fri 8:30 AM – 5: 00 PM (PST/PDT)
Toll Free:1-877-338-0999
info@championpowerequipment.com
Fax no.: 1 (562) 236-9429
Technical Service
Mon – Fri 8:30 AM – 5: 00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
24/7 Tech Support: (562) 204-1188
Page 27
Champion Power Equipment, Inc (CPE),
and the United States Environment Protection Agency (U.S. EPA.)
Emission Control System Warranty
Your Champion Power Equipment (CPE) engine complies with U.S. EPA emission regulations.
YOUR WARRANTY RIGHTS AND OBLIGATIONS:
The US EPA AND CPE are pleased to explain the Federal Emission Control Systems Warranty
on your 1997 and later small off-road engine. New engines must be designed, built and equipped,
at the time of sale, to meet U.S. EPA regulations for small non-road engines. CPE must warrant
the emission control system on your small off-road engine for the period of time listed below,
provided there has been no abuse, neglect, unapproved modification, or improper maintenance of
your small off-road engine.
Your emission control system may include parts such as the carburetor, fuel-injection system, the
ignition system, catalytic converter and fuel lines. Also included may be hoses, belts, connectors
and other emission related assemblies. Where a warrantable condition exits, CPE will repair your
small off-road engine at no cost to you including diagnosis, parts and labor.
MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:
This emission control system is warranted for two years, subject to provisions set forth below. If,
during the warranty period, emission related part on your engine is defective in materials or
workmanship, the part will be repaired or replaced by CPE.
OWNER WARRANTY RESPONSIBILITIES:
As the small off-road engine owner, you are responsible for the performance of the required
maintenance listed in your Owner’s Manual. CPE recommends that you retain all your receipts
covering maintenance on your small off-road engine, but CPE cannot deny warranty solely for the
lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
As the small off-road engine owner, you should however be aware that CPE may deny you
warranty coverage if your small, off-road engine or a part has failed due to abuse, neglect,
improper maintenance or unapproved modifications.
You are responsible for presenting your small off-road engine to an Authorized CPE service outlet,
CPE dealer or CPE, Santa Fe Springs, Ca. as soon as a problem exists. The warranty repairs
should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact:
Champion Power Equipment, Inc.
Customer Service
10006 Santa Fe Springs Road
Santa Fe Springs, CA 90670
Tel: 1-877-338-0999
he emission warranty is a defects warranty. Defects are judged on normal engine performance.
T
The warranty is not related to an in-use emission test.
Page 28
EMISSION CONTROL SYSTEM WARRANTY
The following are specific provisions relative to your Emission Control System Warranty
Coverage.
Emission Control System Warranty (ECS Warranty) for 1997 and later model year engines):
1. APPLICABILITY: This warranty shall apply to 1997 and later model year engines). The ECS
Warranty Period shall begin on the date the new engine or equipment is delivered to its original,
end-use purchaser, and shall continue for 24 consecutive months thereafter.
2. GENERAL EMISSIONS WARRANTY COVERAGE
CPE warrants to the original, end-use purchaser of the new engine or equipment and to each
subsequent purchaser that each of its small off-road engines is:
a. Designed, built and equipped so as to conform at the time of sale with applicable
regulations under section 213 of the Clean Air Ac, as amended, 42 U.S.C. 7401 et seq.
b. Free from defects in materials and workmanship that cause the failure of a warranted
part to be identical in all material respects to the part as described in the engine manufacturer’s
application for certification for a period of two years.
3. THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS
FOLLOWS:
a. Any warranted part that is not scheduled for replacement as required maintenance in
the Owners Manual shall be warranted for the ECS Warranty Period. If any such part fails during
the ECS Warranty Period, it shall be repaired or replaced by CPE according to Subsection “d”
below. Any such part repaired or replaced under the ECS Warranty shall be warranted for any
remainder of the ECS Warranty Period.
b. Any warranted, emissions-related part which is scheduled only for regular inspection
as specified in the Owners Manual shall be warranted for the ECS Warranty Period. A statement
in such written instructions to the effect of “repair or replace as necessary”, shall not reduce the
ECS Warranty Period. Any such part repaired or replaced under the ECS Warranty shall be
warranted for the remainder of the ECS Warranty Period.
c. Any warranted, emissions-related part which is scheduled for replacement as required
maintenance in the Owner’s Manual shall be warranted for the period of time prior to the first
scheduled replacement point for that part. If the part fails prior to the first scheduled replacement,
the part shall be repaired or replaced by CPE according to Subsection “d” below. Any such
emissions-related part repaired or replaced under the ECS Warranty, shall be warranted for the
remainder of the ECS Warranty Period prior to the first scheduled replacement point for such
emissions-related part.
d. Repair or replacement of any warranted, emissions-related part under this ECS
Warranty shall be performed at no charge to the owner at a CPE Authorized Service Outlet.
e. The owner shall not be charged for diagnostic labor which leads to the determination
that a part covered by the ECS Warranty is in fact defective, provided that such diagnostic work is
performed at a CPE Authorized Service Outlet.
f. CPE shall be liable for damages to other original engine components or approved
modifications proximately caused by a failure under warranty of an emission-related part covered
by the ECS Warranty.
g. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted
emission-related parts sufficient to meet the expected demand for such emission-related parts.
h. Any CPE Authorized and approved emission-related replacement part may be used in
the performance of any ECS Warranty maintenance or repair and will be provided without charge
to the owner. Such use shall not reduce CPE’s warranty obligation.
Page 29
i. Unapproved add-on or modified parts may not be used to modify or repair a CPE
engine. Such use voids this ECS Warranty and shall be sufficient grounds for disallowing an ECS
Warranty claim. CPE shall not be liable hereunder for failures of any warranted parts of a
CPE engine caused by the use of such an unapproved add-on or modified part.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list
applicable to the engine)
Systems covered by this warranty Parts Description
Fuel Metering System Fuel regulator, Carburetor and internal parts
Air Induction System Air cleaner, Intake manifold
Ignition System Spark plug and parts, Magneto ignition system
Exhaust System Exhaust manifold, catalytic converter
Miscellaneous Parts Tubing, Fittings, Seals, Gaskets, and Clamps
associated with these listed systems.
TO OBTAIN WARRANTY SERVICE:
You must take your CPE engine or the product on which it is installed, along with your warranty
registration card or other proof of original purchase date, at your expense, to any Champion
Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and
service that CPE product during his normal business hours. Claims for repair or adjustment found
to be caused solely by defects in material or workmanship will not be denied because the engine
was not properly maintained and used.
If you have any questions regarding your warranty rights and responsibilities, or to obtain
warranty service, please write or call the Customer service of Champion Power
Equipment, Inc.
Champion Power Equipment, Inc.
10006 Santa Fe Springs Road
Santa Fe Springs, CA 90670
1-877-338-0999
Attn: Customer Service
Loading...