Chamberlain Elite CSW200501UL, Elite Series, Elite CSW200UL, Elite CSW200101UL Installation Manual

Download

ELITE SERIES COMMERCIAL HIGH-TRAFFIC

AC SWING GATE OPERATOR

INSTALLATION MANUAL

• THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY.

Model CSW200UL

CSW200101UL

1 HP Single Phase

CSW200501UL

1/2 HP Single Phase

• This model is for use on vehicular passage gates ONLY and not intended for use on pedestrian passage gates.

• This model is intended for use in Class I, II, III and IV vehicular swing gate applications.

• Visit LiftMaster.com to locate a professional installing dealer in your area.

• This gate operator is compatible with MyQ® and Security+ 2.0® accessories.

Access installation and technical support guides or register this product

Take a photo of the camera

icon including the points ( ).

Send it in by texting the

photo to 71403.

CSW200ULTECH

LiftMaster 300 Windsor Drive Oak Brook, IL 60523

SAFETY 2

Safety Symbol and Signal Word Review ................................................. 2

Usage Class ............................................................................................ 3

UL325 Entrapment Protection Requirements .........................................3

Safety Installation Information ................................................................ 4

Gate Construction Information ................................................................ 5

INTRODUCTION 6

Carton Inventory ..................................................................................... 6

Operator Specifications ........................................................................... 7

Site Preparation ...................................................................................... 9

Check your gate ...................................................................................... 9

INSTALLATION 10

Types of Installations ............................................................................ 10

Step 1 Determine Location for Operator ............................................... 11

Step 2 Install the Operator .................................................................... 13

Step 3 Position Gate Bracket ................................................................ 14

Step 4 Adjust the Operator Arm Length ................................................ 14

Step 5 Secure the Operator Arm ........................................................... 15

Step 6 Install Entrapment Protection .................................................... 16

Step 7 Earth Ground Rod ...................................................................... 18

Step 8 Power Wiring ............................................................................. 18

Step 9 Dual gate setup .......................................................................... 20

Step 10 Install the Cover ...................................................................... 22

ADJUSTMENT 23

Adjust the Handing and Limits .............................................................. 23

Fine Tune the Force .............................................................................. 24

Obstruction Test ................................................................................... 24

OPERATOR OVERVIEW 25 CONTROL BOARD OVERVIEW 26

Learn Button ......................................................................................... 27

Diagnostic Display ................................................................................ 27

Handing Buttons ................................................................................... 27

Bipart Delay ..........................................................................................27

Timer-to-Close (TTC) ........................................................................... 27

Force Dial .............................................................................................. 28

Test Buttons .......................................................................................... 28

Status LEDs .......................................................................................... 28

WIRE ACCESSORIES TO CONTROL BOARD 29

Three Button Control Station ................................................................ 29

Fire Department .................................................................................... 29

External Control Devices ....................................................................... 29

Photoelectric Sensors and Edge Sensors ............................................. 30

Locks .................................................................................................... 30

EXPANSION BOARD OVERVIEW 31

EXIT FAIL Switch .................................................................................. 31

AC FAIL Switch ..................................................................................... 31

ANTI TAIL Switch .................................................................................. 31

QUICK CLOSE Switch ........................................................................... 31

Auxiliary Relay 1 and 2 ......................................................................... 32

WIRE ACCESSORIES TO EXPANSION BOARD 33

Photoelectric Sensors and Edge Sensors ............................................. 33

Control Station ...................................................................................... 33

Loops .................................................................................................... 34

ADDITIONAL WIRING 34

SAMS Wiring with Relays Not Energized .............................................. 34

Field Wiring ........................................................................................... 35

PROGRAMMING 36

Remote Controls (Not Provided) .......................................................... 36

LiftMaster Internet Gateway (not provided) .......................................... 37

Constant Pressure Override (CPO) .......................................................37

Gate Hold Open Feature ........................................................................ 37

Erase All Codes ..................................................................................... 37

To Remove and Erase Monitored

Entrapment Protection Devices ............................................................. 37

SETTINGS 38

Gate Operator Setup Examples ............................................................. 38

Dual Gate Settings ................................................................................ 39

MAINTENANCE 40

Important Safety Instructions ............................................................... 40

Maintenance Chart ................................................................................ 40

TROUBLESHOOTING 41

Diagnostic Codes .................................................................................. 41

Diagnostic Codes Table ........................................................................ 42

Operator Alarm ..................................................................................... 44

Troubleshooting Chart .......................................................................... 45

ACCESSORIES 47 REPAIR PARTS 49

CSW200501UL 1/2 HP ......................................................................... 49

CSW200101UL 1 HP ............................................................................50

WARRANTY 51

SAFETY

Safety Symbol and Signal Word Review

When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of Serious Injury or Death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your gate and/or the gate operator if you do not comply with the cautionary statements that accompany it. Read them carefully.

IMPORTANT NOTE:

• BEFORE attempting to install, operate or maintain the operator, you must read and fully

understand this manual and follow all safety instructions.

• DO NOT attempt repair or service of your gate operator unless you are an Authorized Service Technician.

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

MECHANICAL

ELECTRICAL

SAFETY

Usage Class

Class I - Residential Vehicular Gate Operator

A vehicular gate operator (or system) intended for use in garages or parking areas associated with a residence of one-to four single families.

Class II - Commercial/General Access Vehicular Gate

A vehicular gate operator (or system) intended for use in a commercial location or building such as a multi-family housing unit (five or more single family units), hotel, garages, retail store, or other buildings accessible by or servicing the general public.

Class III - Industrial/Limited Access Vehicular Gate

A vehicular gate operator (or system) intended for use in an industrial location or building such as a factory or loading dock area or other locations not accessible by or intended to service the general public.

Class IV - Restricted Access Vehicular Gate Operator

A vehicular gate operator (or system) intended for use in a guarded industrial location or building such as an airport security area or other restricted access locations not servicing the general public, in which unauthorized access is prevented via supervision by security personnel.

UL325 Entrapment Protection Requirements

A minimum of two independent* monitored entrapment protection devices are required to be installed at each entrapment zone

l Every installation is unique. It is the responsibility of the installer to

install external monitored entrapment protection devices in each entrapment zone

l This vehicular swing gate operator will operate only after installation

of a minimum of two independent* monitored entrapment protection devices in either the open or close direction. If no entrapment zone exists in the other direction of gate travel, then the inherent (built into the operator) is all that is required in that direction.

l Entrapment protection device types include inherent (built into the

operator), monitored external photoelectric sensors or monitored external edge sensors

l This operator is provided with an inherent entrapment protection

device built into the operator that serves as one of the two independent devices

* Independent - the same type of device shall NOT be used for both entrapment protection devices.

IMPORTANT SAFETY

To reduce the risk of INJURY or DEATH:

l READ AND FOLLOW ALL INSTRUCTIONS. l NEVER let children operate or play with gate controls. Keep the

remote control away from children.

l ALWAYS keep people and objects away from the gate. NO ONE

SHOULD CROSS THE PATH OF THE MOVING GATE.

l Test the gate operator monthly. The gate MUST reverse on contact

with an object or reverse when an object activates the noncontact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust and retest the gate operator properly can increase the risk of INJURY or DEATH.

l Use the emergency release ONLY when the gate is not moving. l KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual.

Have a qualified service person make repairs to gate hardware.

l The entrance is for vehicles ONLY. Pedestrians MUST use separate

entrance.

INSTRUCTIONS

l SAVE THESE

INSTRUCTIONS.

Safety Installation Information

SAFETY

1. Vehicular gate systems provide convenience and security. Gate systems are comprised of many component parts. The gate operator is only one component. Each gate system is specifically designed for an individual application.

2. Gate operating system designers, installers and users must take into account the possible hazards associated with each individual application. Improperly designed, installed or maintained systems can create risks for the user as well as the bystander. Gate systems design and installation must reduce public exposure to potential hazards.

3. A gate operator can create high levels of force in its function as a component part of a gate system. Therefore, safety features must be incorporated into every design. Specific safety features include:

l Edges Sensors (contact) l Photoelectric Sensors l Vertical Posts l Instructional and Precautionary Signage

4. Install the gate operator only when:

a. The operator is appropriate for the construction and the usage

class of the gate.

b. All exposed pinch points are eliminated or guarded, and guarding

is supplied for exposed rollers.

5. The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate access opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.

6. The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures when opening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access areas.

7. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator.

8. Permanently mounted access controls intended for users to activate, must be located at least 6 feet (1.8m) away from any moving part of the gate and where the user is prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or easily accessible controls shall have a security feature to prevent unauthorized use. Exception: Emergency access controls only accessible by authorized personnel (e.g. fire, police) may be placed at any location in the line-of-sight of the gate.

9. The Stop and/or Reset (if provided separately) must be located in the line-of-sight of the gate. Activation of the reset control shall not cause the operator to start.

10. A minimum of two (2) WARNING SIGNS shall be installed in the area of the gate. Each placard is to be visible by persons located on the side of the gate on which the placard is installed.

11. For a gate operator utilizing a non-contact sensor:

a. Reference owner’s manual regarding placement of non-contact

sensor for each type of application. See Install Entrapment Protection section.

b. Care shall be exercised to reduce the risk of nuisance tripping,

such as when a vehicle trips the sensor while the gate is still moving.

c. One or more non-contact sensors shall be located where the risk of

entrapment or obstruction exists, such as the perimeter reachable by a moving gate or barrier.

12. For a gate operator utilizing a contact sensor such as an edge sensor:

a. One or more contact sensors shall be located where the risk of

entrapment or obstruction exists.

b. A hard wired contact sensor shall be located and its wiring

arranged so the communication between the sensor and the gate operator is not subject to mechanical damage.

c. A wireless device such as one that transmits radio frequency (RF)

signals to the gate operator for entrapment protection functions shall be located where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or similar obstruction. A wireless device shall function under the intended end-use conditions.

d. One or more contact sensors shall be located on the inside and

outside leading edge of a swing gate. Additionally, if the bottom edge of a swing gate is greater than 4 inches (10.1 cm) but less than 16 inches (406 mm) above the ground at any point in its arc of travel, one or more contact sensors shall be located on the bottom edge.

SAFETY

Gate Construction Information

Vehicular gates should be installed in accordance with ASTM F2200: Standard Specification for Automated Vehicular Gate Construction. For a copy, contact ASTM directly at 610-832-9585 or www.astm.org.

1. General Requirements

1.1 Gates shall be constructed in accordance with the provisions given for the appropriate gate type listed, refer to ASTM F2200 for additional gate types.

1.2 Gates shall be designed, constructed and installed to not fall over more than 45 degrees from the vertical plane, when a gate is detached from the supporting hardware.

1.3 Gates shall have smooth bottom edges, with vertical bottom edged protrusions not exceeding 0.50inches (12.7 mm) when other than the exceptions listed in ASTM F2200.

1.4 The minimum height for barbed tape shall not be less than 8 feet (2.44m) above grade and for barbed wire shall not be less than 6 feet (1.83m) above grade.

1.5 An existing gate latch shall be disabled when a manually operated gate is retrofitted with a powered gate operator.

1.6 A gate latch shall not be installed on an automatically operated gate.

1.7 Protrusions shall not be permitted on any gate, refer to ASTM F2200 for Exceptions.

1.8 Gates shall be designed, constructed and installed such that their movement shall not be initiated by gravity when an automatic operator is disconnected, in accordance with the following.

1.8.1 Vehicular horizontal swing gate. Shall not result in continuous, unimpeded movement in either direction along the arc of its path of travel.

1.9 For pedestrian access in the vicinity of an automated vehicular gate, a separate pedestrian gate shall be provided. The pedestrian gate shall be installed in a location such that a pedestrian shall not come in contact with a moving vehicular access gate. A pedestrian gate shall not be incorporated into an automated vehicular gate panel.

3. Vehicular Horizontal Swing Gate

3.1 The following provisions shall apply to Class I, Class II and Class III vehicular horizontal swing gates:

3.1.1 Gates shall be designed, constructed and installed so as not to create an entrapment area between the gate and the supporting structure or other fixed object when the gate moves toward the fully open position, subject to the provisions in 3.1.1.1 and 3.1.1.2

3.1.1.1 The width of an object (such as a wall, pillar or column) covered by a swing gate when in the open position shall not exceed 4inches (102mm), measured from the center line of the pivot point of the gate. Exception: For a gate not in compliance with this provision, the defined area must be provided with entrapment protection per UL325.

3.1.1.2 Except for the zone specified in Section 3.1.1.1, the distance between a fixed object such as a wall, pillar or column, and a swing gate when in the open position shall not be less than 16inches (406mm). Exception: For a gate not in compliance with this provision, the defined area must be provided with entrapment protection per UL325.

3.2 Class IV vehicular horizontal swing gates shall be designed, constructed and installed in accordance with security related parameters specific to the application in question.

2. Specific Applications

2.1 Any non-automated gate that is to be automated shall be upgraded to conform to the provisions of this specification.

2.2 This specification shall not apply to gates generally used for pedestrian access and to vehicular gates not to be automated.

2.3 When the gate operator requires replacement, the existing gate shall be upgraded to conform to the provisions of this specification.

2.4 When the gate of an automated gate system requires replacement, the new gate shall conform to the provisions of this specification.

INTRODUCTION

Carton Inventory

NOT SHOWN: Documentation packet and hardware bag

Tools Needed

1/2" wrench for cover screw 5/16", 3/4" wrench for 1/2" concrete anchors, Screwdrivers (phillips head and flat head), Cable cutters and strippers

Operator Specifications

INTRODUCTION

Usage Classification

Main AC Supply Model CSW200501UL 1/2 HP: 120 Vac, 6 Amps (12 Amps including accessory outlets)

Accessory Power

Maximum Gate Weight/Length Model CSW200501UL 1/2 HP: 600 lbs. (272.2 kg), 20 feet (6.1 m)

90 Degree Travel Time*

Maximum Travel Range*

Maximum Daily Cycle Rate

Maximum Duty Cycle

Operating Temperature

Expansion Board

External Entrapment Protection Device Inputs (non-contact and/or contact)

*Travel time and range are affected by A and B mounting dimensions, see INSTALLATION.

Class I, II, III, & IV

Model CSW200101UL 1 HP: 120 Vac, 12 Amps (18 Amps including accessory outlets) When Optional Transformer Kit Model 3PHCONV is installed in the field, operator is rated

208/240/480/575 VAC, 4.8/4.2/2.1/1.7 A, 60 Hz, 1 PH

24 Vdc, 500 mA maximum

Model CSW200101UL 1 HP: 1000 lbs. (453.6 kg), 22 feet (6.7 m)

20 seconds

115 degrees

Continuous

Without Heater: -20°C to 60°C (-4°F to 140°F) With Optional Heater: -40°C to 60°C (-40°F to 140°F)

Provided

Main board - up to 2 close entrapment protection devices and 1 open entrapment protection device.

Expansion board - up to 3 entrapment protection devices configurable to either close or open and up to 4 edge sensors using wireless edge sensor kit model LMWEKITU .

CSW200501UL 1/2 HP

CSW200101UL 1 HP

INTRODUCTION

Site Preparation

Check the national and local building codes BEFORE installation.

Gate

Gate must be constructed and installed according to ASTM F2200 standards (refer to page 4). Gate must fit specifications of operator (refer to specifications).

Safety

Entrapment protection devices are required to protect against any entrapment or safety conditions encountered in your gate application. Install a warning sign (two provided) on the inside and outside of the property, where easily visible.

Conduit and Concrete Pad

Trench and install conduit. Before trenching, contact underground utility locating companies. Conduit must be UL approved for low and high voltage. Consider the operator placement BEFORE installing the pad or post.

Additional Accessories

The vehicle loops allow the gate to stay open when vehicles are obstructing the gate path. Suggested for vehicles 14 feet (4.27 m) or longer. Vehicle loops are not required but are recommended. Before installing your Access Control Device(s) be sure to complete a site survey and determine the best device for your site needs.

Check your gate

Gate MUST be level. Gate and gate post MUST be plumb. Gate MUST have a smooth bottom edge, no protrusions should exist.

Remove ANY/ALL wheels from the bottom of gate.

Gate MUST NOT hit or drag across ground

Gate MUST swing freely and be supported entirely by its hinges.

INSTALLATION

Types of Installations

Standard Installation

The illustration is an example of a standard installation.

Compact Installation

The illustration is an example of a compact installation. If the operator arm will hit an obstruction when the gate is in the open position, refer to LiftMaster.com for compact installation instructions. Entrapment protection devices must be employed in this area.

INSTALLATION

l To AVOID damaging gas, power or other underground utility lines,

contact underground utility locating companies BEFORE digging more than 18 inches (46 cm) deep.

l DO NOT touch the heater when switch is on, heater may be hot.

Step 1 Determine Location for Operator

DO NOT run the operator until instructed.

The illustration below shows the recommended dimensions for a standard installation. If these dimensions are not applicable for your installation refer to the chart on the following page for alternate dimensions.

Standard Installation

Refer to the illustration to determine the measurements and location of the concrete pad.

NOTE: There should only be a maximum of 4" (10.2 cm) from the center of the hinge to the edge of the post or column. If the distance is greater than 4" (10.2 cm) entrapment protection for this area is required.

INSTALLATION

Chart Installation

Refer to the illustration to determine the measurements and location of the concrete pad.

Dimension (A) thru (E) are from the center of one pivot point to the center of another pivot point.

Caution: If the gate is longer than 18 feet (5.5 m), follow CHART A: A-2. Suggestion: The dimensions between the gate and the concrete pad is always 10 inches (25.4 cm) less than the dimension D. Example: D = 42" (106.7 cm), if the dimensions between the gate and the concrete pad is 32" (81.3 cm).

Chart A

A B C D E DISTANCE

(120 cm)

(108 cm)

46"

(116.8

cm)

46.8"

(118.8

cm)

46.8"

(118.8

cm)

47.3"

47"

(119.4

cm)

42.5"

35.5"

(90.2 cm)

35.5"

(90.2 cm)

37"

(94 cm)

37.3"

(94.6 cm)

35"

(90.2 cm)

33"

(116.8

cm)

29.5" (74.9

cm)

33.5" (85.1

cm)

31.5"

(80 cm)

30"

(76.2

cm)

29.5"

(74.9

cm)

26.5"

(67.3

cm)

35"

(90.2 cm)

42"

(106.7

cm)

40"

(101.6

cm)

37"

(94 cm)

32"

(81.3 cm)

28.5"

(72.4 cm)

(27.9

11"

cm) 11"

cm)

11"

cm)

11"

cm)

11"

cm)

11"

cm)

45"

(114.3

cm)

37"

(94 cm)

41"

(104.1

cm)

45"

(114.3

cm)

45"

(114.3

cm)

41"

(104.1

cm)

Chart B

34.5"

(87.6 cm)

44"

(111.8

cm)

44"

(111.8

cm)

45"

(114.3

cm)

44.8"

(113.7

cm)

41"

(104.1

cm)

A B C D E DISTANCE

34.8"

(88.3

cm)

36.5"

(92.7

cm)

37"

(94 cm)

37"

(94 cm)

35.8"

(90.8

cm)

39"

(99.1

cm)

29.5"

(74.9

cm)

32.5"

(82.6

cm)

30.5"

(77.5

cm)

30.5"

(77.5

cm)

29.5"

(74.9

cm)

27.5"

(69.9

cm)

35"

(90.2 cm)

42"

(106.7

cm)

40"

(101.6

cm)

37"

(94 cm)

32"

(81.3 cm)

28.5"

(72.4 cm)

14"

(35.6

cm)

14"

(35.6

cm)

14"

(35.6

cm)

14"

(35.6

cm)

14"

(35.6

cm)

14"

(35.6

cm)

43"

(109.2 cm)

32"

(81.3 cm)

40"

(101.6 cm)

43"

(109.2 cm)

44"

(111.8 cm)

41"

(104.1 cm)

INSTALLATION

Step 2 Install the Operator

CHECK the national and local building codes before installation.

1. Install the electrical conduit.

2. Pour a concrete pad (reinforced concrete is recommended). The concrete pad should be 6 inches (15.2 cm) above the ground and deeper than the frost line. Ensure the pad is tall enough to avoid possible flooding.

3. Secure the operator to the concrete pad with appropriate fasteners.

NOTE: An alternative to a concrete pad is to post mount the operator, see Accessories.

INSTALLATION

Step 3 Position Gate Bracket

NOTE: It may be necessary to attach horizontal reinforcement to the gate before attaching the gate bracket.

1. Position the operator arm onto the output shaft so that the pin slides into the slot.

2. Measure 46" (116.8 cm) along the gate length from the gate hinge center.

3. Measure 27.5" (69.9 cm) up from the concrete pad to the gate hinge position on the gate as shown.

4. Make sure the operator arm is level and tack weld the gate bracket in this position. Use the set screws on the arm to temporarily hold the arm in place while determining the correct measurements.

Step 4 Adjust the Operator Arm Length

NOTE: The length of the arm can be adjusted if necessary. If adjusting the length, ensure that both sections of the arm are adjusted proportionally. Use the set screws on the arm to temporarily hold the arm in place while determining the correct measurements.

1. Close the gate and measure the distance of the operator arm from the gate bracket to the output shaft center. This distance is E.

2. Open the gate 90° (do not allow arms to scissor when open). Measure both sections of the arm (D and C). The arm lengths are correct as long as C+D=E (arm should be perpendicular to the gate in the open position as shown).

INSTALLATION

Step 5 Secure the Operator Arm

Once the operator arm measurements are verified:

1. Weld the gate bracket to the gate.

2. Weld the short arm section.

3. Weld the long arm section.

Remove the set screws from the arm. NOTE: Completely weld around

the outer tubing and bracket.

5. Adjust the nuts on the operator arm so the operator arm fits snug on the output shaft yet still allows enough room to swivel (the handle must be in a 90° position).

6. Tighten the handle by pushing it down. Test to make sure the operator arm does not slip on the output shaft.

INSTALLATION

To prevent SERIOUS INJURY or DEATH from a moving gate:

l ALL gate operator systems REQUIRE two independent entrapment

protection systems for each entrapment zone.

l Entrapment protection devices MUST be installed to protect anyone

who may come near a moving gate.

Step 6 Install Entrapment Protection

Entrapment protection MUST be installed according to the following UL 325 requirements:

l Swing gate operators require the installation of the first external

monitored entrapment protection device to function.

l Every installation is unique. It is the responsibility of the installer to

ensure that ALL entrapment zones are protected with an external monitored entrapment protection device, protecting both the open and close gate cycles.

l LiftMaster monitored external entrapment protection devices MUST

be used with LiftMaster operators to meet UL325 requirements, see Accessories.

l Test ALL entrapment protection devices after completing installation

of the operator. For testing instructions, refer to the manual provided with your entrapment protection device.

l Locate entrapment protection devices to protect in BOTH the open and

close gate cycles.

l Locate entrapment protection devices to protect between moving gate

and RIGID objects, such as posts, walls, pillars, columns, or operator itself.

Definitions

ENTRAPMENT: The condition when a person is caught or held in a position that increases the risk of injury.

SWING GATE ENTRAPMENT ZONE: Locations between a moving gate or moving, exposed operator components and a counter opposing edge or surface where entrapment is possible up to 1.8 m (6 ft) above grade. Such locations occur if during any point in travel:

a. The gap between the bottom of a moving gate and the ground is

greater than 101.6 mm (4 in) and less than 406 mm (16 in); or

b. The distance between the center line of the pivot and the end of the

wall, pillar, or column to which it is mounted when in the open or closed position exceeds 101.6 mm (4 in). Any other gap between a moving gate and fixed counter opposing edges or surfaces or other fixed objects is less than 406 mm (16 in) (examples are walls, curbs, berms or other immovable objects).

Illustrations provided by DASMAGate Systems Safety Guide

INSTALLATION

Wire Entrapment Protection Devices

There are three options for wiring the entrapment protection devices depending on the specific device and how the device will function. Refer to the specific entrapment protection device manual for more information. These entrapment protection device inputs are for monitored devices, which include pulsed photoelectric sensors, resistive edge sensors, and pulsed edge sensors. Only one monitored entrapment protection device may be wired to each input. Additional entrapment protection devices may be wired to the expansion board.

Control Board

CLOSES EYES/INTERRUPT

(2 Terminals) The CLOSE EYES/INTERRUPT input is for photoelectric sensor entrapment protection for the close direction. When an obstruction is sensed during gate closing the gate will open to the full open position and resets the Timer-to-Close. This input will be disregarded during gate opening.

CLOSE EDGE

(2 Terminals) The CLOSE EDGE input is for edge sensor entrapment protection for the close direction. When an obstruction is sensed during gate closing the gate will reverse to the full open position, disengaging the Timer-to-Close. This input will be disregarded during gate opening.

OPEN EYES/EDGE

(2 Terminals) The OPEN EYES/EDGE input is for photoelectric sensor or edge sensor entrapment protection for the open direction. When an obstruction is sensed during gate opening the gate will reverse for 4 seconds then stop. This input will be disregarded during gate closing.

Expansion Board

EYE ONLY and COM

Open or Close Direction Photoelectric Sensors, the functionality is based on the switch settings (located next to the terminals)

Switch set to CLOSE: gate reverses fully when an obstruction is sensed Switch set to OPEN: gate reverses 4 seconds when an obstruction is

sensed

EYE/EDGE and COM

Open or Close Direction Photoelectric Sensors or Edge Sensor, the functionality is based on the switch settings (located next to the terminals)

Switch set to CLOSE: gate reverses fully when an obstruction is sensed Switch set to OPEN: gate reverses 4 seconds when an obstruction is

sensed

INSTALLATION

Step 7 Earth Ground Rod

Use the proper earth ground rod for your local area. The ground wire must be a single, whole piece of wire. Never splice two wires for the ground wire. If you should cut the ground wire too short, break it, or destroy its integrity, replace it with a single wire length.

1. Install the earth ground rod within 3 feet (.9 m) of the operator.

2. Run wire from the earth ground rod to the operator.

NOTE: If the operator is not grounded properly the range of the remote controls will be reduced and the operator will be more susceptible to lightning and surge damage.

Step 8 Power Wiring

To reduce the risk of SEVERE INJURY or DEATH:

l ANY maintenance to the operator or in the area near the operator

MUST NOT be performed until disconnecting the electrical power (AC or solar and battery) and locking-out the power via the operator power switch. Upon completion of maintenance the area MUST be cleared and secured, at that time the unit may be returned to service.

l Disconnect power at the fuse box BEFORE proceeding. Operator

MUST be properly grounded and connected in accordance with national and local electrical codes. NOTE: The operator should be on a

l ALL electrical connections MUST be made by a qualified individual. l DO NOT install ANY wiring or attempt to run the operator without

consulting the wiring diagram.

l ALL power wiring should be on a dedicated circuit and well protected.

The location of the power disconnect should be visible and clearly labeled.

l ALL power and control wiring MUST be run in separate conduit.

separate fused line of adequate capacity.

For dual gate applications, power will have to be connected to each operator. Main power supply and control wiring MUST be run in separate conduits. An optional Transformer Kit (Model 3PHCONV) can be used to change the input voltage (208/240/480/575 Vac) to an output voltage of 120 Vac (refer to Accessories).

NOTE: If using an external receiver use shielded wire for the connections and mount the receiver away from the operator to avoid interference from the operator.

MAXIMUM WIRE LENGTH (FEET)

AMERICAN

WIRE

GAUGE

(AWG)

1/2 HP STANDARD

OPERATOR

120 VAC,

12A (includes

fully loaded

120 VAC, 6A

(operator

only)

outlets)

85 (25.9 m) 165 (50.3 m) 55 (16.8 m) 85 (25.9 m) 360(109.7 m) 480(146.3 m) 1,900(579.1 m) 2,800(853.4 m)

130(39.6 m) 260(79.2 m) 90 (27.4 m) 130(39.6 m) 570 (173.7m) 750 (228.6 m) 3,000 (914.4 m) 4,500(1,371.6 m)

210(64 m) 420(128 m) 140 (42.7 m) 210(64 m) 900 (274.3 m) 1,200(365.8 m) 4,800 (1,463m) 7,100(2,164.1 m)

330(100.6 m) 670(204.2 m) 220 (67.1 m) 330 (100.6m) 1,400(462.7 m) 1,900 (579.1m) 7,600 (2,316.5m) 11,300(3,444.2 m)

530(161.5 m) 1,060(323.1m) 350(106.7 m) 530(161.5 m) 2,300(701 m) 3,000(914.4 m) 12,100 (3,688.1 m) 18,000 (5,486.4 m)

850(259.1 m) 1,700(518.2m) 560(170.7 m) 850(259.1 m) 3,700 (1,127.8m) 4,800 (1,463m) 19,300(5,882.6 m) 28,500(8,686.8 m)

1.0 HP STANDARD OPERATOR

120 VAC,

18A (includes

fully loaded

outlets)

120 VAC,

12A (operator

only)

TRANSFORMER KIT POWERING OPERATOR AND PARTIAL LOAD OF 120

VAC ACCESSORIES

208 VAC, 4.8A 240 VAC, 4.2A 480 VAC, 2.1A 575 VAC, 1.7A

Chart assumes: copper wire, 65°C, 5% drop

INSTALLATION

All control wiring used to connect external devices to Class 2 circuits of the operator must be (QPTZ) Power-Limited Circuit Cables, Type CL2, CL2P, CL2R, or CL2X or other cable with equivalent or better electrical, mechanical, and flammability ratings.

Power wiring

1. Make sure the AC power switch on the operator is OFF (the AC power switch will turn the incoming 120 Vac power ON or OFF).

2. Turn off the AC power from the main power source circuit breaker.

3. Run the AC power wires to the junction box on the operator.

4. Remove the junction box cover.

Connect the green wire to the earth ground rod and AC ground using a wire nut. NOTE: The earth ground rod can be grounded to the chassis.

6. Connect the white wire to NEUTRAL using a wire nut.

7. Connect the black wire to HOT using a wire nut.

8. Replace the junction box cover. Ensure the wires are not pinched.

9. Turn on the AC power from the main power source circuit breaker.

10. Turn on the AC power switch.

INSTALLATION

Step 9 Dual Gate Setup

There are two options for dual gate communication: wired or wireless. Follow the directions according to your application. Do not use wired and wireless communication simultaneously.

Wireless setup

To activate the wireless feature:

Choose an operator to be the network primary operator. All wireless accessories will need to be programmed to the primary operator. NOTE: We

recommend that all accessories and board configurations are set on the primary operator.

Press and release the LEARN button on the primary operator. The green XMITTER LED will light. NOTE: The operator will time out of programming

mode after 180 seconds.

3. Press and release the LEARN button again on the primary operator. The yellow NETWORK LED will light.

4. Press and release the OPEN test button to assign this operator as network primary.

5. Press and release the LEARN button on the second operator. The green XMITTER LED will light.

6. Press and release the LEARN button again on the second operator. The yellow NETWORK LED will light.

7. Press and release the CLOSE test button to assign this operator as network second.

Both operators will beep and the yellow NETWORK LEDs will turn off indicating programming is successful.

To deactivate the wireless feature:

1. Press and release the LEARN button on either operator. The green XMITTER LED will light.

2. Press and release the LEARN button again on the same operator. The yellow NETWORK LED will light.

3. Press and hold the LEARN button for 5 seconds. The yellow NETWORK LED will blink (operator will beep) then turn off indicating successful deactivation.

4. Repeat the steps for the other operator.

INSTALLATION

Wired setup

Before digging, contact local underground utility locating companies. Use PVC conduit to prevent damage to cables.

1. Disconnect ALL power to the operator.

2. Trench across driveway to bury the shielded twisted pair cable.

Connect the wires from the shielded twisted pair cable to the Com Link terminals on the primary gate operator control board. NOTE: We recommend

that all accessories and board configurations are set on the primary operator.

4. Route the shielded twisted pair cable to the secondary gate operator's control board.

5. Connect the wires from the shielded twisted pair cable to the Com Link terminals on the secondary control board (Com Link A to Com Link A and Com Link B to Com Link B). Ground the shield of the cable to the chassis ground of one operator.

6. Connect ALL power to the operator.

DUAL GATE WIRE TYPE (SHIELDED TWISTED PAIR CABLE)

22AWG up to 200feet (61m) 18AWG - 200-1000feet (61-305m)

Wire must be rated at 30 Volt minimum

Bipart delay/synchronized close

The LOCK/BIPART DELAY switch is used only with dual gate applications and serves two functions:

BIPART DELAY

SWING GATE APPLICATIONS: The BIPART DELAY is used in applications where a mag-lock, solenoid lock, or decorative overlay would require one gate to close before the other. The operator with the LOCK/BIPART DELAY switch ON will delay from the close limit when opening and be the first to close from the open limit. SLIDE GATE APPLICATIONS: Not applicable, set to OFF.

SYNCHRONIZED CLOSE

The BIPART DELAY is also used in applications where one gate travels a longer distance than the other. To synchronize the closing of the gates, set the LOCK/BIPART DELAY switch to ON for both operators.

INSTALLATION

Step 10 Install the Cover

Before installing the cover, follow the instructions in the Adjustment section to set the handing and limits.

The operator cover consists of two pieces: a rear cover and a front cover. The front cover can easily be removed to access the electrical box. To access the reset switch slide the access door up. The front cover and access door can be locked with the key.

1/2 HP

1. Remove the operator arm from the output shaft by releasing the handle.

2. Place the rear cover over the operator.

3. Secure both sides of the rear cover to the chassis with the provided screws.

4. Reattach the operator arm to the output shaft (making sure the pin fits into the slot) and secure by pushing the handle down.

5. Place the operator arm cover over the operator arm and secure.

6. Align the front cover with the back cover and fit the front cover into the grooves of the back cover.

7. Secure both sides of the front cover to the chassis with the provided screws.

TO LOCK THE ACCESS DOOR

From the factory the access door for the reset switch will not be locked. To lock the access door follow the steps below:

1. Locate the lock tab on the back of the front cover and remove the screw securing the tab to the cover.

2. Turn the tab 180 degrees, then secure with the screw. The access door can now be locked.

1 HP

1. Remove the operator arm from the output shaft by releasing the handle.

2. Place the rear cover over the operator.

3. Secure both sides of the rear cover to the chassis with the provided screws.

4. Reattach the operator arm to the output shaft (making sure the pin fits into the slot) and secure by pushing the handle down.

5. Place the operator arm cover over the operator arm and secure.

6. Secure the front cover to the back cover.

ADJUSTMENT

Adjust the Handing and Limits

To reduce the risk of SEVERE INJURY or DEATH:

l Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or KILLED by a moving gate.

l Too much force on gate will interfere with proper operation of safety

reversal system.

l NEVER increase force beyond minimum amount required to move

gate.

l NEVER use force adjustments to compensate for a binding or sticking

gate.

l If one control (force or travel limits) is adjusted, the other control

may also need adjustment.

l After ANY adjustments are made, the safety reversal system MUST be

tested. Gate MUST reverse on contact with an object.

The adjustments allow you to set where the gate will stop in the open and close position. The force is adjusted automatically when you set the limits but should be fine tuned using the FORCE dial on the control board (refer to Force Dial section). The Test Buttons on the control board will not work until the handing is set. For dual gate applications the limits will have to be set for each operator. The gate MUST be attached to the operator before setting the limits and force.

OPEN RIGHT: If the operator is installed on the right side of the driveway when looking out of the property, the gate should be set to open right.

OPEN LEFT: If the operator is mounted on the left side of the driveway when looking out of the property, the gate should be set to open left.

Set the handing

1. To set the initial handing of the operator, make sure that both OPEN LEFT and OPEN RIGHT LEDs are flashing. If they are not flashing, press and hold both the OPEN LEFT and OPEN RIGHT handing buttons until both handing LEDs start to flash and the operator beeps.

2. Press and release either the OPEN RIGHT or OPEN LEFT button depending on which direction the gate should open. The corresponding handing LED will turn solid.

To relearn the handing, repeat the steps above.

Set the limits

1. Make sure the gate is closed.

2. Press and release the OPEN test button to open the gate.

3. Press the STOP test button when the desired OPEN limit is reached. Adjust the limit nut or cam so it makes contact with the OPEN limit switch at this position. If the gate stops early, move the limit nut or cam to allow for additional travel.

4. Press and release the CLOSE test button to close the gate.

5. Press the STOP test button when the desired CLOSE limit is reached. Adjust the limit nut or cam so it makes contact with the CLOSE limit switch at this position. If the gate stops early, move the limit nut to allow for additional travel.

HANDING LEDS

OPEN

LEFT LED

OPEN RIGHT

LED

OPERATOR

MODE

EXPLANATION

OFF OFF NORMAL MODE Control board not

powered

BLINKING BLINKING HANDING SETUP

Handing not set

MODE

BLINKING ON HANDING SETUP

MODE

ON BLINKING HANDING SETUP

MODE

Handing set to the

direction of the solid LED

Handing set to the

direction of the solid LED

ON OFF NORMAL MODE Open left handing is set

OFF ON NORMAL MODE Open right handing is set

Set the Force and Run Distance

1. Press the OPEN test button to open the gate.

2. Press and release both the OPEN LEFT and OPEN RIGHT handing buttons.

3. Press the handing button below the solid LED.

4. Run the operator one full cycle using the test buttons. The initial forces and run distance will be set during this cycle.

ADJUSTMENT

Readjust the Limits

To readjust the limits, follow the “Set the Limits” and “Set the Force and Run Distance” instructions above. It is important that the force and run distance are set after every limit readjustment.

Fine Tune the Force

Once the initial limits have been set, the REVERSAL FORCE DIAL on the control board is used for fine tuning the force where wind or environmental changes may affect the gate travel. The REVERSAL FORCE DIAL is set to minimum at the factory.

Based on the length and weight of the gate it may be necessary to make additional force adjustments. The force setting should be high enough that the gate will not reverse by itself nor cause nuisance interruptions, but low enough to prevent serious injury to a person. The force setting is the same for both the open and close gate directions.

Settings 1-3: Fixed force settings (the force will not adjust due to gate wear or temperature changes)

Settings 4-10: Automatically increase the force due to gate wear or temperature changes

1. Open and close the gate with the TEST BUTTONS.

2. If the gate stops or reverses before reaching the fully open or closed position, increase the force by turning the force control slightly clockwise.

3. Perform the “Obstruction Test” after every limit and force setting adjustment (see below).

Obstruction Test

The operator is equipped with an inherent (built in to the operator) obstruction sensing device. If the gate encounters an obstruction during motion, the operator will reverse direction of the gate and then stop. The following procedure will test ONLY the inherent (built in to the operator) obstruction sensing device:

1. Open and close the gate with the TEST BUTTONS, ensuring that the gate is stopping at the proper open and close limit positions.

2. Place an object between the open gate and a rigid structure. Make sure that any external entrapment protection devices will NOT be activated by the object.

3. Run the gate in the close direction. The gate should stop and reverse upon contact with the object. If the gate does not reverse off the object, reduce the force setting by turning the force control slightly counter-clockwise. The gate should have enough force to reach both the open and close limits, but MUST reverse after contact with an object.

4. Repeat the test for the open direction.

Test the operator after any adjustments are made.

OPERATOR OVERVIEW

CONTROL BOARD OVERVIEW

Learn Button

The LEARN button is used for programming (refer to Programming).

Diagnostic Display

The diagnostic display will show the operator type, firmware version, and codes. The operator type will display as “SG” followed by a “20” which indicates the operator type as CSW200UL. The firmware version will show after the operator type, example “1.2”. For more information about the codes refer to the Troubleshooting section.

Handing Buttons

The handing buttons are used to determine which direction the gate will open and they are also used to set the limits (refer to the Adjustment section).

OPEN RIGHT: If the operator is installed on the right side of the drive when looking out of the property, a swing gate will swing to the right (turn counter clockwise) when opening and a slide gate will slide to the right when opening.

OPEN LEFT If the operator is mounted on the left side of the drive when looking out of the property, a swing gate will swing to the left (turn clockwise) when opening and a slide gate will slide to the left when opening.

NOTE: For gates installed on the outside of the property, the setting will be opposite. Determine the direction by looking towards the property from the outside.

Bipart Delay

Used in dual gate applications where a maglock, solenoid lock, or decorative overlay would require one gate to close before the other. The BIPART DELAY is also used in applications where one gate travels a longer distance than the other.

ON/OFF: The operator with the BIPART DELAY dial ON will delay from the close limit when opening and be the first to close from the open limit.

BOTH OFF: No affect. BOTH ON: No affect.

Timer-to-Close (TTC)

The TTC is factory set to OFF (0). Rotate the TIMER-TO-CLOSE dial to the desired setting (0 to 180 seconds). Any radio command, single button control, or CLOSE command on the control board prior to the TTC expiring will close the gate. The TTC is reset by any signals from the open controls, loops, close edges, and close photoelectric sensors.

0 seconds (OFF): The gate will remain open until the operator receives another command from a control. 1-180 seconds (ON): The gate will automatically close after the specified time period.

CONTROL BOARD OVERVIEW

Reversal Force Dial

The REVERSAL FORCE dial adjusts the force. See the Adjustment section. Settings 1-3: Fixed force settings (the force will not adjust due to gate wear or temperature

changes) Settings 4-10: Automatically increase the force due to gate wear or temperature changes

Test Buttons

Used to operate the gate (OPEN, STOP and CLOSE). Also used to view the code history (refer to the Troubleshooting section).

Status LEDs

LED STATE DEFINITION

INPUT POWER

TIMER

GATE MOVING

ACC PWR OVLD

OFF OFF state ON AC power available OFF The timer is disabled ON The timer is enabled 1 blink/second The timer is running 2 blinks/second The timer is paused 8 blinks/second The timer is cancelled OFF The gate is stopped ON The gate is opening or closing 1 blink/second E1 (single entrapment) 8 blinks/second E2 (double entrapment) OFF Accessory power is okay ON Accessory overload protector opened

WIRE ACCESSORIES TO CONTROL BOARD

Three Button Control Station

TERMINALS FUNCTION WIRING EXAMPLE

OPEN and COMM Opens a closed gate. Hard open (maintained switch overrides

external safeties and resets alarm condition). If maintained, pauses Timer-to-Close at OPEN limit. Opens a closing gate and holds open an open gate (within line-of-sight).

CLOSE and COMM Closes an open gate. Hard close (maintained switch overrides

external safeties and resets alarm condition within line-of-sight)

STOP and COMM Stops a moving gate. Hard stop (maintained switch overrides Open

and Close commands and resets alarm condition). If maintained, cancels Timer-to-Close at OPEN limit. Overrides Open and Close commands (within line-of-sight).

Fire Department

TERMINALS FUNCTION WIRING EXAMPLE

FIRE DEPT (-) and OPEN (+)

FIRE DEPT and OPEN terminals act as a hard open. Maintained input overrides (ignores) external safeties (photoelectric sensor and edge), pauses Timer-to-Close. Momentary input logic as single button control and safeties remain active, re-enables Timer-toClose.

External Control Devices

These terminals are used for connecting loops and various control devices such as telephone entry keypads, vehicle probes, etc. Connect the accessory to the terminals based on how the accessory should function.

TERMINALS FUNCTION WIRING EXAMPLE

EXIT and COM This input is a soft open command (maintained switch does not

override external safeties and does not reset alarm condition). Used for exit probe, telephone entry, external exit loop detector, or any device that would command the gate to open.

l Opens a closing gate and holds open an open gate, if

maintained, pauses Timer-to-Close at OPEN limit.

SHADOW and COM This input is used for external shadow loop detector when loop is

positioned under the swing of the gate.

l Holds open gate at open limit l Only active when the gate is at the OPEN limit, disregarded at all

other times

l Pauses Timer-to-Close at OPEN limit

INTERRUPT and COM

This input is used for photoelectric sensors and external interrupt loop detector when loop is on the outside of the gate.

l Holds open gate at open limit l Stops and reverses a closing gate to open limit l Pauses Timer-to-Close at OPEN limit, activates quick close and

anti-tailgate features when enabled on the expansion board

Access Control Device Wiring

Loop Wiring

WIRE ACCESSORIES TO CONTROL BOARD

Photoelectric Sensors and Edge Sensors

The EYES/EDGE terminals are used for connecting entrapment protection devices. At least one external monitored entrapment protection devices are required prior to gate movement. Monitored entrapment protection devices should have been installed with the operator at the time of installation. Only

ONE monitored device may be connected to each input. A monitored device sends a pulsed signal to the operator so the operator is aware of the device. If the operator does not receive the signal from the device indicating it is working properly, it will not run in that direction.

TERMINALS FUNCTION WIRING EXAMPLE

CLOSE EYES/INTERRUPT

CLOSE EDGE The CLOSE EDGE input is for the

OPEN EYES/EDGE The OPEN EYES/EDGE input is for

The CLOSE EYES/INTERRUPT input is for close direction photoelectric sensors. When an obstruction is sensed during gate closing the gate will open to the full open position. This input will be disregarded during gate opening and resets the Timer-to-Close.

close direction edge sensors. When an obstruction is sensed during gate closing the gate will reverse to the full open position, disengaging the Timer-to-Close. This input will be disregarded during gate opening.

open direction photoelectric sensors or edge sensors. When an obstruction is sensed during gate opening the gate will reverse for 4 seconds then stop. This input will be disregarded during gate closing.

Locks

TERMINALS FUNCTION WIRING EXAMPLE

NC and COM Normally Closed (N.C.) output for maglocks. Relay

activates prior to motor activation and during motor run. Relay is off when motor is off.

Maglock Wiring

EXPANSION BOARD OVERVIEW

l To AVOID damaging the circuit board, relays or accessories, DO NOT connect more than 42 Vdc (32 Vac) to the AUX relay contact terminal blocks.

EXIT FAIL Switch

OPEN: If the EXIT plug-in loop detector (model LOOPDETLM) detects a fault, then the gate will open and remain open until fault is cleared. CLOSE: If the EXIT plug-in loop detector (model LOOPDETLM) detects a fault, faults are ignored (EXIT loop is faulted and inoperative).

AC FAIL Switch

NOT USED

ANTI TAIL Switch

OFF: When CLOSE EYES/Interrupt loop is activated it causes a closing gate to stop and reverse. ON: When CLOSE EYES/Interrupt loop is activated it causes a closing gate to pause. Once the vehicle is clear the gate will continue to close.

QUICK CLOSE Switch

OFF: No change to the gate’s normal operation. ON: When CLOSE EYES/Interrupt loop is deactivated it causes an opening or a stopped gate to close (ignores the Timer-to-Close).

EXPANSION BOARD OVERVIEW

Auxiliary Relay 1 and 2

Normally Open (N.O.) and Normally Closed (N.C.) relay contacts to control external devices, for connection of Class 2, low voltage (42 Vdc [34 Vac] max 5 Amps) power sources only. Function of relay contact activation determined by switch settings.

AUX RELAY

SETTING

Off (no feature

selected)

Open Limit Switch

Close Limit Switch

Gate Motion

Pre-Motion Delay

Power

Tamper

Cycle Quantity

Feedback*

SWITCH SETTINGS

1 2 3

OFF OFF OFF Relay always off.

OFF OFF ON

OFF ON OFF

OFF ON ON

ON OFF OFF

ON ON OFF Not used.

ON OFF ON

ON ON ON

Energizes at open limit. Use with SAMS (Sequenced Access Management System, jointly with barrier gate).

Energizes when not at close limit. For an additional audible or visual display, connect an external light (low voltage).

Energizes when motor is on (gate in motion). For an additional audible or visual display, connect an external buzzer or light (low voltage).

Energizes 3 seconds before gate motion and remains energized during gate motion. The onboard alarm will sound. For an additional audible or visual display, connect an external buzzer or light (low voltage).

Energizes if gate is manually tampered with by being pushed off of close limit. For an additional audible or visual display, connect an external buzzer or light (low voltage).

The 1, 2, and 3 LEDs will blink out the cycle count (cycle count is stored on the control board). See below.

AUX RELAY 1 AUX RELAY 2

Energizes 3 seconds before gate motion and remains energized during gate motion. For an additional audible or visual display, connect an external buzzer or light (low voltage).

Red/green light functionality, see below.

* Cycle count

First, note the current Aux Relay switch positions. To determine the actual cycles that the gate operator has run (in thousands), set all three Aux Relay switches to the ON setting for Aux Relay 1. The Expansion Board’s 1, 2, and 3 LEDs will blink out the cycle count, with 1 LED blinking 1000’s, 2 LED blinking 10,000’s, 3 LED blinking 100,000’s, and simultaneously all three LED’s blink 1,000,000’s (e.g. 1 LED blinks 3 times, 2 LED blinks 6 times, and 3 LED blinks once. Cycle count is 163,000.). Cycle count displayed is between 1,000 and 9,999,000 cycles. After servicing, set Aux Relay switches back to their appropriate positions. Cycle count cannot be reset or changed. If under 1,000 cycles the 1, 2, and 3 LEDs will turn on for 10 seconds, then turn off.

NOTE: The expansion board will flash the cycle count 3 times then all the LEDs will turn on solid for 10 seconds then turn off.

Auxiliary relay wiring example

RED/GREEN LIGHT FUNCTIONALITY

Red light wired to AUX RELAY 1. Green light wired to AUX RELAY 2.

GATE STATE

Closed

Opening

Open

Closing

Defined Mid Stop

Undefined Mid Stop

Timer more than 5

seconds

Timer less than 5

seconds

* For red light ON when gate is closed, set switch 1 on AUX RELAY 1 to ON

AUX RELAY 1 SWITCHES

1 OFF 2 OFF 3 OFF 1 ON 2 ON 3 ON

Red light OFF* Green light OFF

Red light ON/Flash Green light OFF

Red light OFF Green light ON

Red light ON/Flash Green light OFF

n/a n/a

Red light ON Green light OFF

Red light OFF Green light ON

Red light ON/Flash Green light OFF

AUX RELAY 2

SWITCHES

WIRE ACCESSORIES TO EXPANSION BOARD

Photoelectric Sensors and Edge Sensors

TERMINALS FUNCTION WIRING EXAMPLE

EYE ONLY and COM Open or Close Direction Photoelectric Sensors, the functionality is

based on the switch settings (located next to the terminals) Switch set to CLOSE: gate reverses fully when an obstruction is

sensed Switch set to OPEN: gate reverses 4 seconds when an obstruction

is sensed

EYE/EDGE and COM Open or Close Direction Photoelectric Sensors or Edge Sensor, the

functionality is based on the switch settings (located next to the terminals)

Switch set to CLOSE: gate reverses fully when an obstruction is sensed

Switch set to OPEN: gate reverses 4 seconds when an obstruction is sensed

EYE/EDGE and COM Open or Close Direction Photoelectric Sensors or Edge Sensor, the

functionality is based on the switch settings (located next to the terminals)

Switch set to CLOSE: gate reverses fully when an obstruction is sensed

Switch set to OPEN: gate reverses 4 seconds when an obstruction is sensed

Control Station

TERMINALS FUNCTION WIRING EXAMPLE

SBC and COM l Gate command sequence - Open, Stop, Close, Stop, ...

l Soft Open, Soft Close, Soft Stop (maintained switch does not

override external safeties and does not reset alarm condition)

OPEN and COM l Open command - opens a closed gate

l Soft open (maintained switch does not override external safeties

and does not reset alarm condition)

l If maintained, pauses Timer-to-Close at OPEN limit l Opens a closing gate and holds open an open gate

CLOSE and COM l Close command - closes an open gate

l Soft close (maintained switch does not override external safeties

and does not reset alarm condition)

STOP and COM l Stop command - stops a moving gate

l If maintained, pauses Timer-to-Close at OPEN limit l Overrides an Open or Close command

WIRE ACCESSORIES TO EXPANSION BOARD

Loops

TERMINALS FUNCTION WIRING EXAMPLE

EXIT Loop wire connection for plug-in loop detector when loop is inside

secured area near gate.

l Open command - opens a closed gate l Soft open (maintained switch does not override external safeties

and does not reset alarm condition)

l If maintained, pauses Timer-to-Close at OPEN limit l Opens a closing gate and holds open an open gate

SHADOW Loop wire connection for plug-in loop detector when loop is

positioned under the gate.

l Holds open gate at open limit l Disregarded during gate motion l Pauses Timer-to-Close at Open Limit

INTERRUPT Loop wire connection for plug-in loop detector when loop is on the

outside of the gate.

l Holds open gate at open limit l Stops and reverses a closing gate l Pauses Timer-to-Close at Open Limit

ADDITIONAL WIRING

SAMS Wiring With Relays Not Energized

ADDITIONAL WIRING

To protect against fire and electrocution:

l DISCONNECT power (AC or solar and battery) BEFORE installing or

servicing operator.

Field Wiring

For continued protection against fire:

l Replace ONLY with fuse of same type and rating.

PROGRAMMING

Remote Controls (Not Provided)

A total of 50 Security+ 2.0®remote controls or KPW250 keypads and 2 keyless entries (1 PIN for each keyless entry) can be programmed to the operator. When programming a third keyless entry to the operator, the first keyless entry will be erased to allow the third keyless entry to be programmed. When the operator’s memory is full it will exit the programming mode and the remote control will not be programmed. The memory will need to be erased before programming any additional remote controls. NOTE: If installing an 86LM to extend the range of the

remote controls DO NOT straighten the antenna.

There are 3 different options for programming the remote control depending on how you would like the remote control to function. Choose a programming option:

OPTION DESCRIPTION PROGRAMMING STEPS

Single button as OPEN only

Single button (SBC) as OPEN, CLOSE, and STOP

Three separate buttons as OPEN, CLOSE, and STOP

Program a single button on the remote control for open only. The Timer-to-Close can be set to close the gate.

Program one remote control button as an open, close, and stop.

Program each remote control button as an open, close, and stop.

1. Press and release the LEARN button (operator will beep and green

XMITTER LED will light). NOTE: The operator will time out of

programming mode after 30 seconds.

2. Press the OPEN button.

3. Press the remote control button that you would like to program.

1. Press and release the LEARN button (operator will beep and green

XMITTER LED will light). NOTE: The operator will time out of

programming mode after 30 seconds.

2. Press the remote control button that you would like to program.

1. Press and release the LEARN button (operator will beep and green

XMITTER LED will light). NOTE: The operator will time out of

programming mode after 30 seconds.

2. Press the OPEN, CLOSE, or STOP button, depending on the desired function.

3. Press the remote control button that you would like to program.

The operator will automatically exit learn mode (operator will beep and green XMITTER LED will go out) if programming is successful. To program additional Security+ 2.0®remote controls or remote control buttons, repeat the programming steps above.

NOTICE: This device complies with Part 15 of the FCC rules and I ndu stry Canada’s license-exempt RSSs. Operation is subject to th e following two conditions: (1) this device may not cause harmful int erference, and (2) th is device must accept any interference received, in cluding interference t hat may cause undesired operation . Any changes or modifications not expressly approved by the party responsible for compliance could void the u ser’s aut hority to o perate th e equipment . This device must be installed to ensure a minimum 20 cm (8 in.) distance is maintained between users/bystanders and device. This device has been tested and f ound to comply with the limits fo r a Class B digital device, pursuant to part 15 of the FCC rules and Ind ustry Canada ICES standard. These limits are designed to provide reasonable protection against h armful interference in a residential installation. This equipment generates, uses and can radiate radio f requency energy and , if not installed and used in accordance with t he instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a p articular installation. If t his equipment does cause harmful interference to radio or t elevision reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase t he separation between the equipment and receiver.

- Connect t he equipment into an o utlet on a circuit diff erent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV t echnician for help.

PROGRAMMING

LiftMaster Internet Gateway (not provided)

To program the operator to the LiftMaster Internet Gateway:

Using the learn button on the opertaor's control board

1. Connect the ethernet cable to the LiftMaster Internet Gateway and the router.

2. Connect power to the LiftMaster Internet Gateway.

3. Create an online account by visiting www.myliftmaster.com.

4. Register the LiftMaster Internet Gateway.

5. Use an internet enabled computer or smartphone to add devices. The LiftMaster Internet Gateway will stay in learn mode for three minutes.

6. Press the Learn button twice on the primary operator (the operator will beep as it enters learn mode). The LiftMaster Internet Gateway will pair to the operator if it is within range and the operator will beep if programming is successful.

Using the reset button on the operator

1. Connect the ethernet cable to the LiftMaster Internet Gateway and the router.

2. Connect power to the LiftMaster Internet Gateway.

3. Create an online account by visiting www.myliftmaster.com.

4. Register the LiftMaster Internet Gateway.

5. Use an internet enabled computer or smartphone to add devices. The LiftMaster Internet Gateway will stay in learn mode for three minutes.

6. Ensure gate is closed.

7. Give the operator an OPEN command.

8. Within 30 seconds, when the gate is at the open limit press and release the reset button 3 times (on primary gate) to put primary operator into High Band Learn Mode (the operator will beep as it enters learn mode). The LiftMaster Internet Gateway will pair to the operator if it is within range and the operator will beep if programming is successful.

The status as shown by the LiftMaster Internet Gateway app will be either “open” or “closed”. The gate operator can then be controlled through the LiftMaster Internet Gateway app.

Constant Pressure Override (CPO)

Constant Pressure Override is for use with KPW5 and KPW250 keypads (not provided). The KPW5/KPW250 wireless commercial keypads are security keypads and can only be programmed to ONE gate operator (see the KPW5/KPW250 manual for complete programming instructions).

The Constant Pressure Override feature is intended to temporarily override a fault in the entrapment protection system, in order to operate the gate until the external entrapment protection device is realigned or repaired. Use the feature only in line of sight of the gate when no obstructions to travel are present. External entrapment protection devices include LiftMaster monitored photoelectric sensors and LiftMaster monitored wired and wireless edge sensors. Be sure to repair or replace these devices promptly if they are not working properly.

To use Constant Pressure Override:

1. Enter a valid 4-digit PIN.

2. Press and hold # for 5 seconds to enter CPO. Continue to hold # to keep the operator in motion. A continuous tone will sound until limit is met and/or # is released.

3. The operator will stop when either the operator reaches a limit or the user releases #.

Gate Hold Open Feature

The gate hold open feature will disable the timer and keep the gate at the open limit. The gate hold open feature can be activated through the Reset Button as described on page 25 or through the KPW5 and KPW250 keypads (not provided).

To use the gate hold open feature:

1. Enter a valid 4-digit PIN when the gate is at the Open Limit and the timer is running

2. The Operator will chirp indicating the timer is canceled.

To restart the gate:

1. Re-enter the 4-digit PIN

2. Activate a Hard input or a programmed remote

Erase All Codes

1. Press and release the LEARN button (operator will beep and green XMITTER LED will light).

2. Press and hold the LEARN button again until the green XMITTER LED flashes and then release the button (approximately 6 seconds). All remote control codes are now erased.

To Remove and Erase Monitored Entrapment Protection Devices

1. Remove the entrapment protection device wires from the terminal block.

2. Press and release the OPEN LEFT and OPEN RIGHT buttons simultaneously. The handing direction LED will remain solid. The other direction LED will begin flashing (entering setup mode).

3. Press the OPEN LEFT and OPEN RIGHT buttons simultaneously to exit.

SETTINGS

Gate operator setup examples

The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site requirements, including all necessary entrapment protection devices.

RESIDENTIAL: One to four residential homes sharing a gated entrance/exit, allowing vehicle access trumps security concerns COMMERCIAL/GENERAL ACCESS: A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle access

trumps security concerns

COMMERCIAL: Business site where security (gate closed) is important INDUSTRIAL: Large business site where security is required

SETTING RESIDENTIAL

Quick Close switch setting

Anti-Tail switch setting

Bipart Delay switch setting

Aux Relay Out – Open Limit Switch

Aux Relay Out – Close Limit Switch

Aux Relay Out – Gate Motion

Aux Relay Out – PreMotion Delay

Cycle Quantity Feedback

Fire D ept Open Input

Heater Accessory (Models HTRNB and HTR460)

Normally set to OFF. Normal gate close (timer or control).

Normally set to OFF. CLOSE EYES/Interrupt loop reverses a closinggate.

For DU AL-GATE site, set to ON for gate that delays uponopening.

Typically not required. Use with SAMS (Sequence Access

Typically not required. Typically not required. Connect “Gate Close/Secure”

Attach alert signal(audible or visual alert system).

Use duringservicingonly to determine operator cycles.

Typically not required. Connect emergency access

The heater keeps the gearbox and batteries at a suitable temperature when the outside temperature is below-4°F. The thermostat MUST be set between 45°F and 60°F to ensure proper gate operation.

COMMERCIAL/GENERAL ACCESS

Normally set to OFF. Normal gate close (timer or control).

Normally set to OFF. CLOSE EYES/Interrupt loop reverses a closinggate.

For DU AL-GATE site, set to ON for gate that delays uponopening.

Management System).

Attach alert signal(audible or visual alert system).

Use duringservicingonly to determine operator cycles.

system (Knox box switch, SO S system, etc.).

The heater keeps the gearbox and batteries at a suitable temperature when the outside temperature is below-4°F. The thermostat MUST be set between 45°F and 60°F to ensure proper gate operation.

COMMERCIAL INDUSTRIAL

Normally set to OFF. Normal gate close (timer or control).

Set to ON. In attempt to prevent vehicle tail-gating, CLOSE EYES/ Interruptlooppauses a closing gate.

For DU AL-GATE site, set to ON for gate that delays uponopening.

1. Use with SAMS (Sequence Access Management System).

2. Connect “Gate Open” indicator (e.g. light).

indicator (e.g. light). Attach alert signal(audible or

visual alert system).

Attach alert signal(audible or visual alert system).

Use duringservicingonly to determine operator cycles.

Typically not required. Typically not required.

The heater keeps the gearbox and batteries at a suitable temperature when the outside temperature is below-4°F. The thermostat MUST be set between 45°F and 60°F to ensure proper gate operation.

Set to ON, so that gate closes immediately after vehicle passes CLOSE EYES/Interrupt loop.

Set to ON. In attempt to prevent vehicle tail-gating, CLOSE EYES/ Interruptlooppauses a closing gate.

For DU AL-GATE site, set to ON for gate that delays uponopening.

1. Use with SAMS (Sequence Access Management System).

2. Connect “Gate Open” indicator (e.g. light).

Connect “Gate Close/Secure” indicator (e.g. light).

Attach alert signal(audible or visual alert system).

Use duringservicingonly to determine operator cycles.

The heater keeps the gearbox and batteries at a suitable temperature when the outside temperature is below-4°F. The thermostat MUST be set between 45°F and 60°F to ensure proper gate operation.

SETTINGS

Dual Gate Settings

NOTE: We recommend that all accessories and board configurations are set on the primary operator.

Main Control Board

FEATURE PRIMARY OPERATOR SECONDARY OPERATOR

Timer-to-Close Set the TTC dial to desired setting OFF

Bi-Part Delay Switch Bi-Part Delay: ON (will open last and close first)

Tandem Mode: OFF

ACCESSORY PRIMARY OPERATOR SECONDARY OPERATOR

Remote Controls Program remote controls 1 to 50 to the primary

operator.

LiftMaster Internet Gateway Program to primary operator.

Garage and Gate Monitor Program to primary operator.

Expansion Board

FEATURE PRIMARY OPERATOR SECONDARY OPERATOR

QUICK CLOSE Switch ON OFF

ANTI-TAIL Switch ON OFF

Bi-Part Delay: OFF (will open first and close last) Tandem Mode: OFF

Program remote controls 51 to 100 to the secondary operator

MAINTENANCE

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

l READ AND FOLLOW ALL INSTRUCTIONS. l ANY maintenance to the operator or in the area near the operator

l Disconnect power at the fuse box BEFORE proceeding. Operator

MUST be properly grounded and connected in accordance with national and local electrical codes. NOTE: The operator should be on

a separate fused line of adequate capacity.

l NEVER let children operate or play with gate controls. Keep the

remote control away from children.

l ALWAYS keep people and objects away from the gate. NO ONE

SHOULD CROSS THE PATH OF THE MOVING GATE.

l The entrance is for vehicles ONLY. Pedestrians MUST use separate

entrance.

l Test the gate operator monthly. The gate MUST reverse on contact

l Use the manual disconnect release ONLY when the gate is NOT

moving.

l KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual.

Have a qualified service person make repairs to gate hardware.

l ALL maintenance MUST be performed by a LiftMaster professional. l Activate gate ONLY when it can be seen clearly, is properly adjusted

and there are no obstructions to gate travel.

l SAVE THESE INSTRUCTIONS.

To protect against fire and electrocution:

l DISCONNECT power (AC or solar and battery) BEFORE installing or

For continued protection against fire:

l Replace ONLY with fuse of same type and rating.

servicing operator.

Maintenance Chart

Disconnect all power to the operator before servicing.

DESCRIPTION TASK CHECK AT LEAST ONCE

EVERY

MONTH 6 MONTHS

Entrapment Protection Devices Check and test inherent (built into the operator) and external devices for proper operation X Warning Signs Make sure they are present and replace if worn or broken, see Accessories X Manual Disconnect Check and test for proper operation X Belt and Pulley Check for excessive slack, wear or damage X Gate Inspect for wear or damage; ensure it still complies with ASTM F2200, see page 5 X Accessories Check all for proper operation X Electrical Inspect all wire connections X Chassis Mounting Bolts Check for tightness X Operator Inspect for wear or damage X

NOTES:

l Severe or high cycle usage will require more frequent maintenance checks. l It is suggested that while at the site voltage readings be taken at the operator. Using a digital voltmeter, verify that the incoming voltage to the operator

is within ten percent of the operator’s rating.

TROUBLESHOOTING

To protect against fire and electrocution:

l DISCONNECT power (AC or solar and battery) BEFORE installing or

servicing operator.

Diagnostic Codes

To View the Codes

The codes will show on the diagnostic display.

The operator will show the code sequence number followed by the code number:

For continued protection against fire:

l Replace ONLY with fuse of same type and rating.

To Scroll Through the Saved Codes

The operator will only keep track of up to 20 codes, then will start saving over the oldest codes as new codes occur.

To Exit

Press and release the STOP button to exit. The display will also time out after two minutes of inactivity.

To Reset the Code History

1. Press and hold the STOP button for six seconds. The display will show "Er" then "CL" alternately for six seconds.

2. Release the STOP button. The code history has now been reset and the display will show "- -" until a new code occurs.

3. Press and release the STOP button to exit.

TROUBLESHOOTING

Diagnostic Codes Table

Some codes are saved in the code history and some are not. If a code is not saved it will briefly appear on the display as it occurs, then disappear.

LiftMaster System Installed System Informational

Code Meaning Solution Saved

Main control board has experienced an internal failure.

Max-Run-Time Exceeded Error Check for an obstruction, then reprogram the limits. YES

Product ID Error Was the control board just replaced? If so, erase limits, enter limit setup

Product ID Failure Unplug product ID harness then plug back in. Disconnect all power, wait

Exit Loop Error Failure or missing loop (SHORT or OPEN - LiftMaster Plug-in Loop

Shadow Loop Error

Interrupt Loop Error

Wireless edge battery low Replace batteries in wireless edge. YES

Power board fault Relay fault detected in the power board. Replace the power board. YES

Run-Distance Error The limits are less than the minimum requirement or longer than what

Brownout occurred

Wireless Second Operator Communication Error

System AC Overvoltage Call utility. YES

System AC Undervoltage Check wiring and wire gauge to operator. YES

Limit Error - Stuck Switch

Limit Error - Wrong Switch Check motor wiring. YES

Missing Power Board Check harness for shorts. Check for presence of power board. YES

Minimum number of monitored entrapment protection devices not installed.

CLOSE EYE/INTERRUPT held more than 3 minutes

CLOSE EDGE held more than 3 minutes

OPEN EYE/EDGE held more than 3 minutes

CLOSE EYE/INTERRUPT held more than 3 minutes

CLOSE EYE/EDGE held more than 3 minutes

OPEN EYE/EDGE held more than 3 minutes

Wireless edge triggered more than 3 minutes Check wired input for wiring issue or obstruction. YES

Wireless edge loss of monitoring Check wireless edge inputs. YES

Wireless edge triggered

Disconnect all power, wait 15 seconds, then reconnect power (reboot). If issue continues, replace main control board.

mode and set limits. If not, disconnect all power, wait 15 seconds, then reconnect power before changing product ID harness.

15 seconds, then reconnect power before replacing product ID harness.

Detector only) Check loop wiring throughout connection. May be a short in the loop, or an open connection in the loop.

was learned. Check limit positions and proper switch function. Rundistance can be re-learned by setting the handing again.

AC/DC board supply dipped below allowable level. Review power supply and wiring. If rebooting, ensure enough time for discharge of power to force a fresh boot.

Check the second operator for power. If OFF, restore power and try to run the system. If powered, deactivate the wireless feature and then re-learn the second operator.

Check switch for proper operation. Check harness for shorts. Replace if defective.

Review monitored entrapment protection device connections. This swing gate operator will operate only after installation of a minimum of one external safety device in either the open or close direction.

Check wired input on main control board; check for alignment or obstruction.

Check wired input on expansion board; check for alignment or obstruction. The photoelectric sensors may be installed too far apart.

IF an obstruction occurred, no action required. If an obstruction did NOT occur, check inputs and wiring.

External Entrapment Protection

Inherent Entrapment Protection

YES

TROUBLESHOOTING

Code Meaning Solution Saved

CLOSE EYE/INTERRUPT triggered, causing

reversal, preventing close, or resetting TTC

CLOSE EDGE triggered, causing reversal, NO

preventing close, or canceling TTC

OPEN EYE/EDGE triggered, causing reversal or

preventing opening

CLOSE EYE/INTERRUPT triggered, causing

reversal, preventing close, or resetting TTC

CLOSE EYE/EDGE triggered, causing reversal and

preventing close or canceling TTC

OPEN EYE/EDGE triggered, causing reversal or

preventing opening

Close input (EYE/EDGE) communication fault from

other operator

Open input (EYE/EDGE) communication fault from

other operator

Close input (EYE/EDGE) communication fault

(expansion board)

Open input (EYE/EDGE) communication fault

(expansion board)

Non-monitored device detected on the wireless

safety system

Force Reversal (Operator 1)

RPM / STALL Reversal (Operator 1)

AC motor no start condition

Current Sensor Fault

99 Normal Operation No action required YES

IF an obstruction occurred, no action required. If an obstruction did NOT occur, check alignment, inputs, and wiring on main control board

IF an obstruction occurred, no action required. If an obstruction did NOT occur, check alignment, inputs, and wiring on expansion board.

Check inputs and communication method between operators, either wired bus or radio. Ensure operator is powered. May have to erase the wireless communication and reprogram the two operators.

Check the connections between the main board and the expansion board. YES

Non-monitored contact closure devices are not supported. Make sure connected devices are monitored. Check edges for proper orientation and resistive end cap connection.

Check for obstruction. If no obstruction, check that the mechanical assembly is engaged and free to move. See section on Limit and Force Adjustment, and Obstruction Test.

Check for obstruction. If no obstruction, check the operator wiring and that the mechanical assembly is engaged and free to move. Replace APE assembly.

Motor start sequence failed. If the gate and motor are NOT moving, or moving too slow, check for an obstructed gate, binding in the mechanism, and relay board and start capacitor connections. If the gate and motor ARE moving, failure is due to loss of the encoder signal. Check the encoder cup and sensor on the limit shaft, and wiring.

A fault was detected on the current sensor. Make sure the current sensor is connected to the main control board. Check the current sensor harness for an open or short. The operator will need a power cycle to resume operation after correcting the fault. If the fault continues, replace the power board.

YES

TROUBLESHOOTING

Operator Alarm

If a contact sensor detects an obstruction twice consecutively the alarm will sound (up to 5 minutes) and the operator will need to be reset.

When the inherent force of the operator (RPM/current sensor) detects the following (twice consecutively) the alarm will sound (up to 5 minutes) and the operator will need to be reset.

A. The operator arm or gate is incorrectly installed. B. The gate does not meet specifications. C. Gate hinges are too tight or broken and the gate is not moving freely. D. The gate is moving and a car pushes the gate.

E. A foreign object is on the gate frame while the gate is moving.

F. The gate hits the driveway or curb and gets stuck or bent in an

awkward position.

Remove any obstructions. Press the reset button to shut off the alarm and reset the operator. After the operator is reset, normal functions will resume.

TROUBLESHOOTING

Troubleshooting Chart

SYMPTOM POSSIBLE CAUSES SOLUTIONS

Operator does not run and diagnostic display not on.

Control board powers up, but motor does not run.

Gate moves, but cannot set correct limits.

Gate does not fully open or fully close when setting limits.

Operator does not respond to a wired control/command (example: Open, Close, SBC, etc.)

Operator does not respond to a wireless control or transmitter

Gate stops during travel and reverses immediately.

Gate opens, but will not close with transmitter or Timer-to-Close.

Gate closes, but will not open.

Exit loop activation does not cause gate to open.

Interrupt loop does not cause gate to stop and reverse.

Shadow loop does not keep gate at open limit.

a. No power to control board

b. Open fuse

c. Defective control board

a. Reset switch is stuck

b. Stop button active or jumper not in place

for stop circuit

c. Open or Close input active

d. Entrapment Protection Device active

e. Vehicle loop detector or probe active

f. Defective control board

a. Gate does not move to a limit position

b. Gate is too difficult to move

a. Gate does not move to a limit position

b. Gate is too difficult to move

a. Check Open and Close command input

LEDs

b. Stop button is active

c. Reset button is stuck

d. Entrapment Protection Device active

e. Vehicle loop detector or vehicle probe

active

a. Check XMITTER LED when wireless

control is active

b. Stop button is active

c. Reset button is stuck

d. Poor radio reception

a. Control (Open, Close) becoming active

b. Vehicle loop detector active

a. Open control active

b. Vehicle loop detector active

c. Fire Dept input active

d. Timer-to-Close not set

e. Close Entrapment Protection Device active

a. Vehicle loop detector active a. Check all vehicle detector inputs for an active detector

a. Exit vehicle detector setup incorrectly

b. Defective Exit loop detector

a. Vehicle detector setup incorrectly

b. Defective vehicle loop detector

a. Vehicle detector setup incorrectly

b. Defective vehicle loop detector

a. Check AC power

b. Check fuses

c. Replace defective control board

a. Check reset switch

b. Check Stop button is not “stuck on”, or verify that the stop button is a

normally closed circuit, or put a jumper on the stop circuit.

c. Check all Open and Close inputs for a “stuck on” input

d. Check all Entrapment Protection Device inputs for a “stuck on” sensor

e. Check all vehicle detector inputs for a “stuck on” detector

f. Replace defective control board

a. Use manual disconnect, manually move gate, and ensure gate moves

easily limit to limit. Repair gate as needed.

b. Gate must move easily and freely through its entire range, limit to limit.

Repair gate as needed.

a. Use manual disconnect, manually move gate, and ensure gate moves

easily limit to limit. Repair gate as needed.

b. Gate must move easily and freely through its entire range, limit to limit.

Repair gate as needed.

a. Check all Open and Close inputs for a “stuck on” input

b. Check Stop button is not “stuck on”

c. Check Reset button

d. Check all Entrapment Protection Device inputs for a “stuck on” sensor

e. Check all vehicle detector inputs for a “stuck on” detector

a. Activate wireless control and check XMITTER LED is on. Re-learn

wireless control/transmitter to control board. Replace wireless control as needed.

b. Check Stop button is not “stuck on”

c. Check Reset button

d. Check if similar wired control operates correctly. Check if wireless

controls works properly when within a few feet of operator. Check operator’s antenna and antenna wire. Check other wireless controls or devices.

a. Check all Open and Close inputs for an active input

b. Check all vehicle detector inputs for an active detector

a. Check all Open inputs for an active input

b. Check all vehicle detector inputs for an active detector

c. Check Fire Dept input

d. Check Timer-to-Close (TTC) setting

e. Check all Entrapment Protection Device inputs for an active sensor

a. Review Exit loop detector settings. Adjust settings as needed.

b. Replace defective Exit loop detector.

a. Review Interrupt loop detector settings. Adjust settings as needed.

b. Replace defective Interrupt loop detector.

a. Review Shadow loop detector settings. Adjust settings as needed.

b. Replace defective Shadow loop detector.

TROUBLESHOOTING

SYMPTOM POSSIBLE CAUSES SOLUTIONS

Obstruction in gate's path does not cause gate to stop and reverse.

Photoelectric sensor does not stop or reverse gate.

Edge Sensor does not stop or reverse gate.

Alarm sounds for 5 minutes or alarm sounds with a command.

On dual-gate system, incorrect gate opens first or closes first.

Alarm beeps when running.

Expansion board function not controlling gate.

Maglock not working correctly.

Solenoid lock not working correctly.

Quick Close not working correctly.

Anti-Tailgating not working correctly.

AUX Relay not working correctly.

a. Force adjustment needed a. Refer to the Adjustment section to conduct the obstruction test and

a. Incorrect photoelectric sensor wiring

b. Defective photoelectric sensor

c. Photoelectric sensors installed too far apart

a. Incorrect edge sensor wiring

b. Defective edge sensor

a. Double entrapment occurred (two

obstructions within a single activation)

a. Incorrect Bipart switch setting a. Change setting of both operator’s Bipart switch settings. One operator

a. Expansion board setting

b. Constant pressure to open or close is given

a. Defective main board to expansionboard

wiring

b. Incorrect input wiring to expansion board

c. Defective expansion board or defective

main board

a. Maglock wired incorrectly a. Check that Maglock is wired to N.C. and COM terminals. Check that

a. Solenoid wired incorrectly a. Check that Solenoid is wired to N.O. and COM terminals. Check that

a. Quick Close setting incorrect

b. Interrupt loop detector

c. Defective Expansion board

a. Anti-Tail setting incorrect

b. Interrupt loop detector

c. Defective Expansion board

a. AUX Relay setting incorrect

b. AUX Relay wiring incorrect

c. Defective Expansion board

perform the proper force adjustment that is needed.

a. Check photoelectric sensor wiring. Retest that obstructing photoelectric

sensor causes moving gate to stop, and may reverse direction.

b. Replace defective photoelectric sensor. Retest that obstructing

photoelectric sensor causes moving gate to stop, and may reverse direction.

c. Move the photoelectric sensors closer together or use edge sensors

instead.

a. Check edge sensor wiring. Retest that activating edge sensor causes

moving gate to stop and reverse direction.

b. Replace defective edge sensor. Retest that activating edge sensor causes

moving gate to stop and reverse direction.

a. Check for cause of entrapment (obstruction) detection and correct. Press

the reset button to shut off alarm and reset the operator.

should have Bipart switch ON (operator that opens second) and the other operator should have Bipart switch OFF (operator that opens first).

a. Pre-warning is set to "ON"

b. Constant pressure to open or closed is given

a. Check main board to expansion board wiring. If required, replace wire

cable.

b. Check wiring to all inputs on expansion board.

c. Replace defective expansion board or defective main board

Maglock has power (do not power maglock from control board accessory power terminals). If shorting lock’s NO and COM wires does not activate Maglock, then replace Maglock or Maglock wiring (refer to Wiring Diagrams).

Solenoid has power (do not power solenoid from control board accessory power terminals). If shorting lock’s NC and COM wires does not activate Solenoid, then replace Solenoid lock or Solenoid wiring (refer to Wiring Diagrams).

a. Check that Quick Close setting is ON

b. Check operation of Interrupt Loop detector

c. Replace defective Expansion board

a. Check that Anti-Tail setting is ON

b. Check operation of Interrupt Loop detector

c. Replace defective Expansion board

a. Check AUX Relay switches settings

b. Check that wiring is connected to either N.O. and COM or to N.C. and

COM.

c. Set AUX Relay to another setting and test. Replace defective expansion

board.

ACCESSORIES

Universal single and 3-button remote controls

Ideal for applications requiring a large number of remote controls.

Models 811LM and 813LM

Security+ 2.0®learning remote controls

One button can control a gate operator and the other(s) can control garage door(s). It can also be programmed to Security+®or Security+ 2.0®code format.

Models 892LT and 894LT

LiftMaster®internet gateway

Internet enabled accessory which connects to the computer and allows you to monitor and control gate operators and lighting accessories enabled by MyQ®technology.

Model 828LM

LiftMaster Cloud™ connected access protocol high capacity

Model CAPXL

Plug-in loop detector

Low power. Conveniently plugs into existing control board.

Model LOOPDETLM

LiftMaster elite series maglock package

Model MG1300RLYPKG

Heater kit accessory

Model HTRNB Model HTR460 for 460V applications

Post-mounting plate

For post-mounting models CSL24UL and SL3000 commercial slide gate operators. Posts not included.

Model MPEL

Steel stand for mounting to concrete pad

Model MSEL

Uphill swivel arm

Model K75-50292

LiftMaster door and gate monitor

Model 829LM

3-button control station

Model 02-103

Stop Button

Model AEXITP

Power Hinges

Warning sign

Model 40-3505

Transformer kit

Changes input voltage (208/240/480/575 Vac) to an output voltage of 120 Vac. Rated 208/240/480/575 Vac, 4.8/4.2/2.1/1.7 A, 60 Hz, 1 PH

Model 3PHCONV

ACCESSORIES

Entrapment protection

If the gate opening distance is greater than the maximum separation distance of the photoelectric sensors, then edge sensors MUST BE USED. Refer to the photoelectric sensor instructions for maximum separation distance.

LiftMaster monitored through beam photoelectric sensor

Model LMTBUL

LiftMaster monitored retro-reflective photoelectric sensor

Model LMRRUL

LiftMaster monitored wireless edge kit (transmitter and receiver)

Model LMWEKITU

LiftMaster monitored wireless edge transmitter

Model LMWETXU

Large profile monitored edge (82 ft. roll)

Model L50

Large profile ends kit (10 pair)

Model L50E

Small profile monitored edge (82 ft. roll)

Model S50

Small profile ends kit (10 pair)

Model S50E

Plastic channel

8 ft. (2.4 m) for both small and large profile edges (pack of 10). Model L50CHP

Aluminum channel for edge (pack of 8)

10 ft. (3.1 m) for small and large profile edges. Model L50CHAL

LiftMaster large profile monitored edges (4ft.,5ft., 6ft.)

Model L504AL, L505AL, L506AL

LiftMaster small profile monitored edges (4ft.,5ft., 6ft.)

Model S504AL, S505AL, S506AL

Edge cutting tool

Model ETOOL

CSW200501UL 1/2 HP

NOT SHOWN

Plastic Standoffs for main control board (10 per bag)

Reset Button with ID Hall Effect Sensor Board Wire Harnesses (main board to power board, main

board to ground, main board to transformer, and power board to transformer)

Wire Harness (main board to expansion board)

REPAIR PARTS

K77-37683

K94-37449 K1D8247 K77-37693

K94-34778

CSW200101UL 1 HP

NOT SHOWN

Plastic Standoffs for main control board (10 per bag)

Reset Button with ID Hall Effect Sensor Board Wire Harnesses (main board to power board, main

board to ground, main board to transformer, and power board to transformer)

Wire Harness (main board to expansion board)

REPAIR PARTS

K77-37683

K94-37449 K1D8247 K77-37693

K94-34778

WARRANTY

LiftMaster 7 Year residential / 5 Year Commercial Limited Warranty

LiftMaster (“Seller”) warrants to the first purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of 7 Year residential / 5 Year Commercial from the date of purchase [and that the CSW200UL is free from defect in materials and/or workmanship for a period of 7 Year residential / 5 Year Commercial from the date of purchase]. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety.

If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-2806, toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair. You will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-of-purchase receipt with any product returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and covered by this limited warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid. Defective parts will be repaired or replaced with new or factoryrebuilt parts at Seller’s sole option.

ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE 7 YEAR RESIDENTIAL / 5 YEAR COMMERCIAL LIMITED WARRANTY PERIOD SET FORTH ABOVE [EXCEPT THE IMPLIED WARRANTIES WITH RESPECT TO THE CSW200UL, WHICH ARE LIMITED IN DURATION TO THE 7 YEAR RESIDENTIAL / 5 YEAR COMMERCIAL LIMITED WARRANTY PERIOD FOR THE CSW200UL, AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, OR REPLACEMENT OF BATTERIES.

THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GATE OR GATE HARDWARE, INCLUDING BUT NOT LIMITED TO THE GATE SPRINGS, GATE ROLLERS, GATE ALIGNMENT OR HINGES. THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU.

UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

300 Windsor Drive

Oak Brook, IL 60523

LiftMaster.com

01-39374B

Chamberlain Elite CSW200501UL, Elite Series, Elite CSW200UL, Elite CSW200101UL Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TABLE OF CONTENTS

SAFETY

Safety Symbol and Signal Word Review

Usage Class

UL325 Entrapment Protection Requirements

Safety Installation Information

Gate Construction Information

INTRODUCTION

Carton Inventory

Operator Specifications

Site Preparation

Check your gate

INSTALLATION

Types of Installations

Step 1 Determine Location for Operator

Step 2 Install the Operator

Step 3 Position Gate Bracket

Step 4 Adjust the Operator Arm Length

Step 5 Secure the Operator Arm

Step 6 Install Entrapment Protection

Step 7 Earth Ground Rod

Step 8 Power Wiring

Step 9 Dual Gate Setup

Step 10 Install the Cover

ADJUSTMENT

Adjust the Handing and Limits

Fine Tune the Force

Obstruction Test

OPERATOR OVERVIEW

CONTROL BOARD OVERVIEW

Learn Button

Diagnostic Display

Handing Buttons

Bipart Delay

Timer-to-Close (TTC)

Reversal Force Dial

Test Buttons

Status LEDs

WIRE ACCESSORIES TO CONTROL BOARD

Three Button Control Station

Fire Department

External Control Devices

Photoelectric Sensors and Edge Sensors

Locks

EXPANSION BOARD OVERVIEW

EXIT FAIL Switch

AC FAIL Switch

ANTI TAIL Switch

QUICK CLOSE Switch

Auxiliary Relay 1 and 2

WIRE ACCESSORIES TO EXPANSION BOARD

Photoelectric Sensors and Edge Sensors

Control Station

Loops

ADDITIONAL WIRING

SAMS Wiring With Relays Not Energized

Field Wiring

PROGRAMMING

Remote Controls (Not Provided)

LiftMaster Internet Gateway (not provided)

Constant Pressure Override (CPO)

Gate Hold Open Feature

Erase All Codes

To Remove and Erase Monitored Entrapment Protection Devices

SETTINGS

Gate operator setup examples

Dual Gate Settings

MAINTENANCE

Maintenance Chart

TROUBLESHOOTING

Diagnostic Codes

Diagnostic Codes Table

Operator Alarm

Troubleshooting Chart

ACCESSORIES

CSW200501UL 1/2 HP