Chamberlain 41A7305-1 User Manual

SMART CONTROL PANEL

Model 41A7305-1

Botón "LEARN" (APRENDIZAJE) amarillo

Safety Reversing Sensors

Détecteurs inverseurs de sécurité

Sensores de inversión de seguridad

FEATURE OVERVIEW

Yellow LEARN Button

Touche jaune LEARN

Smart Control Panel

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is NOT connected BEFORE installing door control.

• Connect ONLY to 12 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

• Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.

• NEVER permit children to operate or play with door control push buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

WARNING: This product can expose you to chemicals including lead, which are known to the State of

California to cause cancer or birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov

For use with MyQ® Garage Door Openers. The features are adjustable and may be turned off or on as desired. Refer to the Feature Settings section.

SCREEN

The screen will display the time and temperature until the menu button is pressed, and then it will display the menu options. If there is a problem with the garage door opener the screen will display the Diagnostic Code.

LIGHT BUTTON

Press the LIGHT button to turn the garage door opener lights on or off. When the lights are turned on they will stay on until the LIGHT button is pressed again, or until the garage door opener is activated. Once the garage door opener is activated the lights will turn off after the specified period of time (the factory setting is 4-1/2 minutes). The LIGHT button will not control the lights when the door is in motion. The duration of the light timing can be adjusted by accessing the menu using the navigation buttons.

MOTION SENSOR

The motion sensor will automatically turn on the garage door opener lights when motion is detected. The lights will come on for the set period of time, then shut off. The factory setting is on and set at 4-1/2 minutes.

LOCK

The LOCK feature is designed to prevent activation of the garage door opener from remote controls while still allowing activation from the door control and keyless entry. This feature is useful for added peace of mind when the home is empty (i.e. vacation).

TIMER-TO-CLOSE (TTC)

DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY with sectional doors. Factory default is set to off. TTC can be set to automatically close your garage door from the fully open position after a specified period of time (1, 5, 10 minute intervals or a custom setting up to 99 minutes). The garage door opener will beep and the lights will flash before closing the door. The screen on the door control can display the status of the TTC. TTC WILL NOT work if the garage door opener is operating by battery power or if the safety reversing sensors are misaligned. This feature is NOT intended to be the primary method of closing the door. A keyless entry should be installed in the event of an

accidental lock out when using this feature.

C D

HARDWARE

7/16" (11 mm) 7/16 de po. (11 mm) 11 mm (7/16 de pulg.)

DRYWALL

6ABx1-1/4" 6AB x 1-1/4 po. 6ABx1-1/4 de pulg.

Drywall Anchors Chevilles pour mur sec Tarugos para panel de pared

GANG BOX

6-32x1" 6-32 x 1 po 6-32x1 de pulg.

7/16" (11 mm) 7/16 de po. (11 mm) 11 mm (7/16 de pulg.)

WHITE BLANC BLANCO

RED

ROUGE

ROJO

GREY GRIS

INSTALLATION

WIRE THE DOOR CONTROL

Install the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from the moving parts of the door. For gang box installations it is not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang box.

NOTE: Pre-wiring means that your garage already has wires installed for the door control.

1 Unplug the garage door opener to prevent the garage door

opener from activating during wiring.

2 Strip 7/16 inch (11 mm) of insulation from one end of the wire

and separate the wires.

3 Connect one wire to each of the two screws on the back of the

door control. The wires can be connected to either screw.

PRE-WIRED INSTALLATIONS: Choose any two wires to connect, but make note of which wires are used.

MOUNT THE DOOR CONTROL

1 Mark the location of the bottom mounting hole and drill a 5/32

inch (4 mm) hole.

2 Install the bottom screw, allowing 1/8 inch (3 mm) to protrude

from the wall.

3 Position the bottom hole of the door control over the screw and

slide down into place. 4 Lift the push bar up and mark the top hole. 5 Remove the door control from the wall and drill a 5/32 inch

(4 mm) hole for the top screw. 6 Position the bottom hole of the door control over the screw and

slide down into place. Attach the top screw. 7 Close the push bar.

WIRE TO GARAGE DOOR OPENER

1 Strip 7/16 inch (11 mm) of insulation from the end of the wire

near the garage door opener.

2 Connect the wire to the red and white terminals on the garage

door opener. The wires can be connected to either terminal. To insert or release wire, push in tab with screwdriver tip.

3 Reconnect power to the garage door opener. If the door control

has been installed and wired correctly, a message will display on the screen. To synchronize the garage door opener and the door control, press the push bar up to 3 times, until the garage door opener activates. The time and temperature will display on the door control when the door control and the garage door opener are synchronized.

PRE-WIRED INSTALLATIONS: Connect the same wires to the garage door opener that were previously connected to the door control.

Navigation Buttons

Touches de navigation

Botones de navegación

Touche LIGHT (éclairage)

OPERATION

Push Bar

Barre de poussée

Pulsador de barra

LIGHT Button

Botón de luz

Screen Écran Pantalla

Motion Sensor Détecteur de mouvement

Detector de movimiento

PUSH BAR

Press the push bar to open or close the door.

NAVIGATION BUTTONS

Use the navigation buttons to make selections and program features.

GARAGE DOOR OPENER LIGHTS

MOTION SENSOR

This feature will automatically turn on the garage door opener lights when motion is sensed. The lights will come on for the set period of time, then shut off.

LIGHT FEATURE

The lights will turn on when someone enters through the open garage door and the safety reversing sensor infrared beam is broken.

If using the garage door opener light as a work light, turn the light on using the light button on the wall control or the light will turn off if you are beyond the range of the sensor.

TIMER-TO-CLOSE (TTC)

DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY with sectional doors. Once the TTC has been set and the door is open, the selected close interval will be displayed on the screen and toggle between the time and TTC message. The garage door opener will beep and the lights will flash before closing the door. When the TTC is on the following message will display on the door control:

To temporarily suspend the TTC feature press and release the HOLD button. Press REL button to resume normal TTC operation.

The TTC feature will deactivate if the garage door encounters two sequential obstructions; or the safety reversing sensors are incorrectly installed. The garage door will reverse open and WILL NOT close until the obstructions are removed or the safety reversing sensors are correctly installed. When the obstruction has been cleared or the safety reversing sensors have been aligned, the door will close when the garage door opener is activated.

LOCK

When the Lock feature is on, your remote controls have been disabled and the following message will display on the door control:

BATTERY BACKUP ONLY

If your garage door opener has a battery backup one of the following messages will display on the door control if there is a problem with the battery:

+ 5 hidden pages