Chamberlain 379LMC-10, 379LM-10 User Manual

Model 379LM-10 and 379LMC-10

Fingerprint Keyless Entry

Overview

For use with any 315 MHz SECURITY®® garage door openers having a purple "learn" button (refer to Step 4.)

The system uses biometric technology that enables an authorized user to gain access by scanning their ﬁ ngerprint. The sensor strip on the unit makes a numeric template of the ﬁ ngerprint that is unique to that user. The unit’s memory can store up to ten ﬁ ngerprints.

• The term “enroll” refers to scanning the ﬁ ngerprint so the device will recognize the user.

• The term “swipe” refers to the movement of the ﬁ nger across the sensor strip.

• The term “LED” stands for Light Emitting Diode. There are 6 LEDs located on the Fingerprint Keyless Entry.

When unit is on, it is programmed to shut off after a short period of time. The unit’s sensor strip is sensitive so it is important to read the Tips for Success before attempting to use the Fingerprint Keyless Entry.

Step 1 Install the Unit

1. Remove cover.

2. Fasten bottom screw to mounting surface. Allow 1/8" (3 mm) to protrude above surface. Position unit on screw head and adjust for snug ﬁ t.

3. Fasten top screw. Replace cover.

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• Install Keyless Entry Control within sight of the garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modiﬁ cations of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards for Home or ofﬁ ce use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Tips for Success

CORRECT

1. Make sure ﬁ nger is clean and dry. Place ﬁ nger ﬂ at above the sensor strip with the top knuckle above the sensor.

2. Swipe ﬁ nger straight down keeping ﬁ rm contact with the sensor. The swipe should be a slow, constant speed.

SPECIAL NOTES: Use the same ﬁ nger for every swipe. It is important to swipe ﬁ nger slowly and ﬁ rmly as this is the reason most swipes fail.

Swipe finger straight down

keeping firm contact with Start swipe with the top knuckle above the sensor strip.

Sensor Strip

the sensor.

Sensor Strip

The scan should end at the tip of finger.

INCORRECT

• Do not bend ﬁ nger during swipe as this will only scan the tip of

your ﬁ nger.

• Swipe ﬁ nger straight down, not at an angle.

• Swipe ﬂ at, not tilted or rolled to one side.

Reference

Step 3 Enroll Additional Users

NOTE: The device can store up to ten ﬁ ngerprints at a time. An enrolled user must swipe ﬁ nger ﬁ rst to enroll new user.

Cover

Resend button: When pressed the door will stop if moving up or reverse if moving down.

Send LED (yellow): Lit after a passed fingerprint scan and indicates that the Resend button is active and can be used to stop or reverse door travel.

Pass LED (green): Lit when a scanned fingerprint matches a stored print.

Ready LED (green): Lit when unit is ready to scan fingerprint.

Extra directions are located on the inside of cover.

SEND

PASS

READY

Sensor Strip

ENROLL

RETRY

1. Open cover and wait until Ready

LED is lit.

ENROLL

Enroll button: When pressed the unit will go into Enroll mode.

Enroll LED (yellow): Lit when the unit is in Enroll mode.

2. Press and hold Enroll button until Enroll LED starts to ﬂ ash.

SEND

PASS

READY

ENROLL

FAIL

RETRY

Fail LED (red): Lit when a scanned fingerprint

FAIL

does not match a stored print.

Retry LED (yellow): Lit when another swipe is required.

3. While the Enroll LED is ﬂ ashing an enrolled user must slowly and ﬁ rmly swipe ﬁ nger.

4. The Enroll LED and Ready LED will light when ready for new user to swipe ﬁ nger.

ENROLL

Step 2 Enroll Initial User

NOTE: The unit requires 3 passed swipes to enroll a user.

1. Open cover to turn unit on. Wait until Enroll LED and Ready LED are lit (not ﬂ ashing).

2. Swipe ﬁ nger slowly and ﬁ rmly

down the sensor strip until three passed swipes are made.

NOTE: The Pass LED will light for a passed swipe. The Retry LED will light if another swipe is needed. Swipe slowly and with more pressure if this occurs.

3. After the third passed swipe, the

Enroll and Pass LED will ﬂ ash. Enrollment is complete.

SEND

PASS

READY

SEND

PASS

READY

ENROLL

FAIL

RETRY

ENROLL

FAIL

RETRY

5. New user should swipe ﬁ nger slowly and ﬁ rmly down the sensor

SEND

PASS

READY

ENROLL

FAIL

RETRY

strip until three passed swipes are made.

6. The Enroll LED and Pass LED will ﬂ ash when new user is enrolled. Unit will return to Ready mode.

ENROLL

SEND

PASS

READY

ENROLL

FAIL

RETRY

NOTE: If cover is already open, press either the Resend or the Enroll button to turn unit on. The Pass LED will light for a passed swipe. The Retry LED will light if another swipe is needed.

NOTE: If cover is already open, press either the Resend or the Enroll button to turn unit on. If the Ready LED is lit refer to Factory Reset in the Erase/Reset section.

Step 4 Program to Opener

Step 5 Operation

1. Open cover and wait until Ready LED is lit.

ENROLL

NOTE: The unit must have an enrolled user before it can be programmed to the opener. Due to the 30 second time interval, a second person may be needed to press the “learn” button. If there is no purple “learn” button refer to Troubleshooting.

1. Press and release the purple “learn” button on the motor unit of the garage door opener. See illustration above.

2. Open cover and wait for Ready LED to light.

3. Within 30 seconds of pressing the “learn” button, slowly and ﬁ rmly

ENROLL

SEND

PASS

READY

ENROLL

FAIL

RETRY

swipe enrolled ﬁ nger.

NOTE: The Retry LED will light if another swipe is needed.

2. Swipe ﬁ nger slowly and ﬁ rmly down the sensor strip.

3. The Pass LED will ﬂ ash and garage door will either open or close.

SEND

PASS

READY

SEND

PASS

ENROLL

FAIL

RETRY

ENROLL

FAIL

RETRY

NOTE: If cover is already open, press either the Resend or the Enroll button to turn unit on. The Fail or Retry LED will light if another swipe is needed. If this occurs, swipe slowly and with more pressure. It may require multiple swipes to get a passed swipe.

While the door is traveling the Send LED will be lit. During this time the only way to reverse or stop the door is to press the Resend button.

4. After a passed swipe the Pass LED will light followed by a lit Send LED. The opener lights will ﬂ ash. Programming is complete.

5. If the opener lights don’t ﬂ ash,

ENROLL

SEND

PASS

READY

ENROLL

FAIL

RETRY

press and release the Resend button at 1 second intervals for up to 5 seconds until the opener lights ﬂ ash or the door moves. Programming is complete.

NOTE: If unit will not program to opener repeat the steps above or refer to Troubleshooting.

+ 5 hidden pages