Page 1
Page 2
Contents
Safety alert symbol review ...........................................2
Safety information and precautions..............................3
Testing your garage door for binding & balance..........3
Hardware supplied........................................................3
Carton inventory ...........................................................4
Illustration of sectional door installation .....................5
Illustration of one-piece door installation.....................5
Assembly section - pages 6 – 7
Fasten rail to power unit .............................................6
Install the trolley.........................................................6
Attach the rail brackets ...............................................7
Installation safety instructions ....................................7
Installation section - pages 8 – 23
Determine the header bracket location
Sectional door ...........................................................8
One-piece door..........................................................9
Install the header bracket..........................................10
Attach the rail to the header bracket .........................11
The Protector System
®
.............................................12
Install the safety reversing sensor.............................13
Position the opener....................................................15
Hang the opener........................................................16
Install the door control and connect all wires...........17
Electrical requirements .............................................18
Complete the safety reversing sensor installation.....18
Install the lights and lens ..........................................19
Attach the manual release rope and handle...............19
Fasten the door bracket (sectional door)...................20
Fasten the door bracket (one-piece door)..................21
Connect door arm to trolley (sectional door)............22
Connect door arm to trolley (one-piece door)...........23
Adjustment section - pages 24 – 26
Travel limit adjustments............................................24
Force adjustments .....................................................25
Test the Protector System
®
........................................26
Test the safety reverse system ..................................26
Operation safety instructions ......................................27
Care of your opener ....................................................27
Maintenance schedule.................................................27
Operation of your opener............................................28
Receiver & remote control programming...................29
Having a problem?......................................................30
Repair parts, rail assembly..........................................32
Repair parts, installation .............................................32
Repair parts, power unit..............................................33
Accessories .................................................................34
Index ...........................................................................35
How to order repair parts............................................36
Warranty......................................................................36
Start by reviewing these important safety alert symbols:
When you see these Safety Symbols on the following pages, they will alert you to the possibility of
or death if you do not comply with the corresponding instructions. The hazard may come from something
mechanical or from electric shock. Read the instructions carefully.
serious injury
Mechanical Electrical
When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage to your
garage door and/or the garage door opener if you do not comply with the corresponding instructions. Read the
instructions carefully.
This garage door opener is designed and tested to offer safe service provided it is installed, operated, maintained
and tested in strict accordance with the safety instructions contained in this manual.
2
Page 3
To avoid damage to the garage door and opener, disable
locks before installing and operating the opener . Use a
wood screw or nail to hold locks in the "open" (unlocked)
position.
Operation at other than 120V 60 Hz will cause opener
malfunction and damage.
Safety Reversing Sensor
Installation
Lag Screw 1/4 x 1-1/2" (4)
Hex Screw 1/4-20 x 1-1/2" (2)
Carriage Bolts 1/4" - 20 x 1/2" (4)
Screw #10 - 32 x 3/8" (4)
Lock Nut 1/4" - 20 (4)
Lock Nut #10 x 32 (4)
Wing Nut (2)
Insulated Staples (20)
Rail Assembly
Coupling Sleeve (1)
Hex Screw 1/4"-20 x 5/8" (4)
Nut 1/4" - 20 (4)
Identify the type and height of your door, any special
conditions that exist, and any additional materials that
may be required.
Test Your Door for Balance
Before you begin, complete the following test to make
sure your door is balanced, and is not sticking or
binding:
• Lift the door about halfway as shown. Release the door.
It should stay in place, supported entirely by its springs.
• Raise and lower the door to see if there is any binding
or sticking.
Hardware Supplied
Sectional
Door
One-Piece
Door
Safety Information and Precautions
Opener Installation
Hex Screw 5/16"-18 x 7/8" (4)
Lag Screw 5/16"-9 x 1-5/8" (2)
Lag Screw 5/16"-18 x 1-7/8" (2)
Carriage Bolt 5/16"-18 x 2-1/2" (2)
Clevis Pin 5/16" x 2-3/4" (1)
Clevis Pin 5/16" x 1-1/4" (1)
Clevis Pin 5/16" x 1" (1)
Nut 5/16" - 18 (6)
Lock Washer 5/16" (6)
Screw 6AB x 1" (2)
Insulated Staples (10)
Ring Fastener (3)
Handle
Dry Wall Anchors (2)
Rope
An unbalanced gara ge door might not re verse when
required and someone under the door could be seriously
injured or killed.
If your garage door binds, sticks or is out of balance, call
for professional garage door service.
springs, cables, pulleys, brackets, and their hardware are
under extreme tension and can cause serious injur y or
death.
yourself!
Ropes left on a gara ge door could cause someone to
become entangled and killed.
connected to the door before installing and operating the
opener.
Do not tr y to loosen, mo ve or adjust them
Garage doors, door
Remove all r opes
3
Page 4
Page 5
Before you begin, survey your garage area to see whether any of the conditions below apply to
your installation.
SECTIONAL Door or
ONE-PIECE Door with Track Installation
Horizontal and vertical reinforcement
is needed for lightweight garage doors
(fiberglass, steel, aluminum, door with glass panels, etc.).
See page 20 for details.
Header Wall
— — — — — — — —
Door Center
Extension Spring
OR
Torsion Spring
Safety
Reversing
Sensor
FINISHED CEILING
Support bracket &
fastening hardware
is required.
See page 13.
One-Piece Door-Extension Spring
Door
OR
Header
Wall
Track
Access Door
Floor must be level
across width of door
Safety Reversing Sensor
ONE-PIECE Door Without Track Installation
Header
Wall
FINISHED CEILING
Support bracket
& fastening
hardware is required.
See page 13.
Access Door
Safety
Reversing
Sensor
Gap between floor and bottom of
Safety Reversing Sensor
door must not exceed 1/4".
You may find it helpful to refer back to this page as you proceed with the installation of your opener.
5
Page 6
Rail
Sprocket
Rail
Assembly
Trolley
Coupling
Rail/Power Unit
Bracket
Lock Nuts
1/4"-20
Power Unit
Sprocket
Opener
Chassis
Foam Packaging
Hex Screws
1/4"-20x5/8"
Assembly Section: Pages 6 - 7
ASSEMBLY STEP 1
Fasten the Rail To the Power Unit
NOTE: To aid in assembly and installation, replace
the foam packing around the power unit. Remove it
after Installation Step 5.
• Working on a level surface, align the rail assembly with
the power unit, as shown.
• Slip the coupling over the rail sprocket.
• Slide the rail through the power unit bracket until the
coupling fits securely over the power unit sprocket.
• Align the two screw holes in the rail with those in the
power unit bracket. Insert two 1/4"-20x5/8" hex screws
and lock nuts. Tighten securely with a 7/16" socket
wrench.
ASSEMBLY STEP 2
Install the Trolley
As illustrated above, slide the trolley onto and along the
bottom of the rail until it snaps firmly in place. Be certain
to install it facing correctly: the trolley release arm must
be horizontal (lock position), with its arrow pointed
away from the power unit.
Hardware Shown Actual Size
1/4" - 20
Lock Nut
1/4" - 20 x 5/8"
Hex Screw
6
Page 7
ASSEMBLY STEP 3
Attach the Rail Brackets
• Align rail brackets to end of rail assembly, as shown.
• Insert two 1/4"-20 x 5/8" hex screws and lock nuts.
Tighten securely with a 7/16" socket.
Hardware Shown Actual Size
1/4" - 20 x 5/8"
Hex Screw
1/4" - 20
Lock Nut
1/4"-20x5/8
Hex
Screws
Rail
Brackets
Rail
1/4"-20
Lock Nuts
You have now finished assembling your garage door opener. Please read the following warnings
before proceeding to the installation section:
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING
WARNING
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS
2. Install only on a properly balanced and lubricated garage door. An improperly balanced door may not
reverse and could result in severe injury or death. Repairs to cables, spring assemblies and other
hardware must be made by a professional service person before installing opener.
3. Disable all locks and remove all ropes connected to the garage door before installing the opener. Ropes
connected to a garage door can cause entanglement and death.
4. If possible, install door opener 7 feet or more above floor with the manual release handle mounted 6
feet above the floor.
5. Do not connect the opener to power source until instructed to do so.
6. Locate the Door Control within sight of the door at a minimum height of 5 feet where small children
cannot reach and away from all moving parts of the door.
7. Install the User Safety Instruction Label on the wall adjacent to the control button and the
Maintenance Instruction Label in a prominent location on the inside of the garage door.
8. Upon completion of the installation, the door must reverse when it comes in contact with a one-inch
high object or a 2x4 laid flat on the floor.
9. Do not wear watches, rings or loose clothing while installing or servicing an opener. Jewelry or loose
clothing can be caught in the mechanism of the garage door or the opener.
7
Page 8
Installation Section: Pages 8 – 23
Installation Step 1
Determine Header Bracket Location
Installation procedures vary according to garage
door types. Follow the instructions which apply to
your door.
SECTIONAL Door or
ONE PIECE Door with Track
Finished
Ceiling
2x4
Header
Wall
Vertical
Guideline
Vertical
Guideline
Structural
Supports
WARNING
If the header bracket is not rigidly fastened to a
structural support on the header wall or ceiling, the
safety reverse system may not work properly (see page
26).
The door might not reverse when required, and
could cause serious injury or death.
The garage door springs, cables, pulleys, brackets and
their hardware are under extreme tension.
to loosen, move or adjust them yourself. Serious
personal injury or death could result.
professional garage door service.
• Close the door and mark the inside
vertical centerline of the garage door.
• Extend the line onto the header wall
above the door.
Remember, you can fasten the header
bracket within 2 feet of the left or right
of the door center only if a torsion
spring or center bearing plate is in the
way; or you can attach it to the ceiling
(refer to page 10) when clearance is
minimal. (It may be mounted on the
wall upside down if necessary, to gain
approximately 1/2".)
If you need to install the header bracket on
a 2x4 (on wall or ceiling), use lag screws
(not supplied) to securely fasten the 2x4 to
structural supports as shown here and on
page 9.
Do not attempt
Call for
• Open your door to the highest point
of travel as shown. Draw an intersecting horizontal line on the header
wall 3" above the high point. This
height will provide travel clearance
for the top edge of the door.
Proceed to Step 2, page 10.
Ceiling
Header
Wall
3"
Highest Point
of Travel
Door
Sectional door
with curved track
8
Track
Header
Wall
3"
Highest Point
Door
One-piece door
with horizontal track
Track
of Travel
Page 9
ONE-PIECE Door Without Track
Read the Safety Instructions on page 8. They also apply to doors without tracks.
• Close the door and mark the inside
vertical centerline of your garage
door. Extend the line onto the
header wall above door.
If headroom clearance is minimal,
you can install the header bracket
on the ceiling. See page 10.
• If you need to install the header
bracket on a 2x4 (on wall or
ceiling), use lag screws (not
supplied) to securely fasten the 2x4
to structural supports as shown.
Header Wall
Highest Point
of Travel
Header Wall
Vertical
Centerline
2x4
Vertical
Centerline of
Garage Door
Header
Wall
Unfinished
Ceiling
Structural Supports
2x4
Header Support
OPTIONAL CEILING MOUNT
FOR HEADER BRACKET
Highest Point
of Travel
Door
Jamb
Hardware
Distance
Floor
One-piece door without track
jamb hardware
• Open your door to the highest point of travel as shown.
Measure the distance from the top of the door to the
floor. Subtract the actual height of the door. Add 8" to
the remainder. (See Example).
• Close the door and draw an intersecting horizontal line
on the header wall at the determined height.
If the total number of inches exceeds the height
available in your garage, use the maximum height
possible, or refer to page 10 for ceiling installation.
Door
Distance
Pivot
Floor
One-piece door without track
pivot hardware
EXAMPLE
Distance from top of door
(at highest point of travel) to floor................................92"
Actual height of door...................................................-88"
Remainder.......................................................................4"
Add...............................................................................+8"
Bracket height on header wall....................................=12"
(Measure UP from top of CLOSED door.)
Proceed to Step 2, page 10.
9
Page 10
Installation Step 2
Hardware Shown Actual Size
Install the Header Bracket
You can attach the header bracket either to the wall
above the garage door, or to the ceiling. Follow the
instructions which will work best for your particular
requirements.
Fastening the Header Bracket to the Wall
• Center the bracket on the vertical guideline with the
bottom edge of the bracket on the horizontal line as
shown (with the arrow pointing toward the ceiling).
• Mark either set of bracket holes (do not use the holes
designated for ceiling mount). Drill 3/16" pilot holes
and fasten the bracket securely to a structural support
with the hardware provided.
Fastening the Header Bracket to the Ceiling
• Extend the vertical guideline onto the ceiling as shown.
• Center the bracket on the vertical mark, no more than 6"
from the wall. Make sure the arrow is pointing toward
the wall. The bracket can be mounted flush against the
ceiling when clearance is minimal.
• Mark holes designated for ceiling mount only. Drill
3/16" pilot holes and fasten bracket securely to a
structural support with the hardware provided.
10
Page 11
Installation Step 3
Hardware Shown Actual Size
Attach the Rail to the Header Bracket
• Position the opener on the garage floor below the
header bracket. Use packing material as a protective
base.
If the door spring is in the way you’ll need help. Have
someone hold the opener securely on a temporary
support to allow the rail to clear the spring.
• Position the rail bracket against the header bracket.
• Align the bracket holes and join with a clevis pin as
shown.
• Insert a ring fastener to secure.
11
Page 12
The Protector System
Information you'll need before you begin the installation of the safety reversing sensor
The safety reversing sensor must be connected and
aligned correctly before the garage door opener will
move in the down direction. This is a required safety
device and cannot be disabled.
Installation procedures are the same for sectional and
one-piece doors.
Be sure power to the opener is disconnected.
The sending eye transmits an invisible light beam to the
receiving eye. The units can be installed on either side of
the garage door as long as the sun never shines directly
into the receiving eye lens.
Look at the label on the connector end of each case to
identify the sensors.
The brackets must be connected and fastened so that the
sending and receiving eyes face each other as shown.
If an obstruction breaks the light beam while the garage
door is closing, the door will stop and reverse to full open
position and the opener lights will flash for 5 seconds.
The brackets must be securely fastened to a solid surface
such as the studs on either side of the door, or add a piece
of wood at each location if installing in masonry
construction.
The invisible light beam path must be unobstructed. No
part of the garage door (or door tracks, springs, hinges,
rollers or other hardware) can interrupt the beam while
the door is closing. If it does, use a piece of wood to build
out each sensor mounting location to the minimum depth
required for light beam clearance.
®
WARNING
Without a properly working safety reversing sensor,
persons (particularly children) could be injured or killed
by a closing garage door.
instructions.
To protect small children, install the safety reversing
sensor so that the beam will be no higher than 4"-6"
above the garage floor.
Disconnect power to the garage door opener before
installing the safety reversing sensor.
Read and follow all
Sensor
Beam
4-6" max.
above floor
Invisible Light Beam
Protection Area
Facing the door from inside the garage
12
Sensor
Beam
4-6" max.
above floor
Page 13
Installation Step 4
Install the Safety Reversing Sensor (Receiving and Sending Eyes)
Figures 1, 2 and 3 show recommended assembly of
bracket(s) and "C" wrap based on the wall installation of
the sensors on each side of the garage door as shown on
page 12, or on the garage door tracks themselves.
Figures 4 and 5 are variations which may fit your
installation requirements better. Make sure the wraps
and brackets are aligned so the sensors will face each
other across the garage door.
Garage Wall or Door Track Installation Procedure
• Fasten the "C" wraps to the mounting brackets having
square holes, using the hardware shown in 1.
Garage Wall Installation Procedure
• Connect each assembly to a slotted bracket, using the
hardware shown in 2. Note alignment of brackets for
left and right sides of the door.
• Finger tighten the lock nuts.
• Use bracket mounting holes as a template to locate and
drill (2) 3/16" diameter pilot holes on both sides of the
garage door, 4"-6" above the floor but not exceeding 6"
(see warning on page 12).
• Attach bracket assemblies with 1/4"x1-1/2" lag screws
as shown in 2.
• Adjust right and left side bracket assemblies to the same
distance out from mounting surface. Make sure all door
hardware obstructions are cleared. Tighten the nuts
securely.
Figure 1
Garage WALL or DOOR TRACK Installation
Mounting Bracket
With Square Holes
#10 - 32
Lock Nuts
"C" Wrap
Figure 2
Garage WALL Installation
1/4 x 1-1/2"
Lag Screws
Inside
Garage
Wall
Mounting Bracket
with Slot
1/4" - 20
Lock Nuts
1/4-20 x 1/2" Carriage Bolts
Mounting Bracket
with Square Holes
Figure 3
Garage DOOR Track Installation
1/4 " Lock Nuts
Garage
Door Track
Drill 3/8"
Holes
Inside
Garage
Wall
#10-32x3/8"
Screws
(with square shoulder)
"C" Wrap
Mounting Bracket
with Square Holes
Garage Door Track Installation Procedure
Discard slotted bracket. Drill 3/8" holes in each track and
fasten securely with hardware as shown in 3.
Hardware Shown Actual Size
#10 - 32 x 3/8"
Screw
Figure 4
#10 x 32
Lock Nut
Alternate Wall Mount
Inside
Garage
Wall
Mounting Bracket
with Slot
Mounting Bracket
with Square Holes
"C" Wrap
Garage
Floor
1/4 x 1-1/2"
Lag Screw
Sensor
Indicator Light
13
1/4-20 x 1/2"
Carriage Bolts
Figure 5
Staples
1/4" - 20 x 1/2"
Carriage Bolts
Alternate Floor Mount
Inside
Garage
Wall
"C" Wrap
Indicator Light
Sensor
Mounting Bracket
"C" Shaped
Wrap
1/4" - 20
Lock Nut
Mounting Bracket
with Square Holes
with Slot
Attach with
concrete anchors
(not provided)
Garage
Floor
Page 14
Page 15
Installation Step 5
Position the Opener
Follow instructions which apply to your door
type as illustrated.
SECTIONAL Door or
ONE-PIECE Door with Track
A 2x4 laid flat is convenient for setting an ideal doorto-rail distance.
• Raise the opener onto a stepladder.
You will need help at this point if the ladder is not tall
enough.
• Open the door all the way and place a 2x4 laid flat on
the top section beneath the rail.
If the top panel hits the trolley when you raise the door,
pull down on the trolley release arm to disconnect the
inner and outer sections. The trolley can remain
disconnected until Step 12 is completed.
CAUTION
To prevent damage to steel, aluminum, fiberglass or
glass panel doors, do not rest the opener on the door
without using a 2x4.
Rail
Door
2x4
Foam
Packaging
Trolley
Trolley
Release Arm
ONE-PIECE Door without Track
• With the door fully open and parallel to the floor,
measure the distance from the floor to the top of the
door.
• Using a stepladder as a support, raise the opener to the
same distance as the door from the floor (it will be at a
slight angle as shown).
• The top of the door should be level with the top of the
opener. Do not position the opener more than 3" above
this point.
Header
Bracket
Top of Opener
Foam
Packaging
Top of Door
15
Page 16
Installation Step 6
Hang the Opener
Two representative installations are shown. Yours
may be different. Hanging brackets should be angled,
Figure 1, to provide rigid support. On finished ceilings,
Figure 2, attach a sturdy metal bracket to structural
supports before installing the opener. The bracket and
fastening hardware are not supplied.
• Measure the distance from each side of the opener to
the structural support.
• Cut both pieces of the hanging bracket to required
lengths.
• Drill 3/16" pilot holes in the structural supports.
• Attach one end of each bracket to a support with
5/16"x1-7/8" lag screws.
• Fasten the opener to the hanging brackets with
5/16" - 18x7/8" screws, lock washers and nuts.
• Check to make sure the rail is centered over the door
(or in line with the header bracket if the bracket is not
centered above the door).
• Remove the 2x4. Operate the door manually. If the
door hits the rail, raise the header bracket.
WARNING
The opener could fall and injure someone if it is not
properly secured.
structural supports of the garage.
Figure 1
Measure
Distance
5/16"-18x7/8"
Hex Screws
5/16" Lock Washers
5/16"-18 Nuts
Fasten the opener securely to
Structural
Supports
Lag Screws
5/16"x1-7/8"
CONTROL
CENTER
Preferred Range of
Bracket Placement
Hardware Shown Actual Size
Lag Screw
5/16"-18 x 1-7/8"
Hex Screw
5/16"- 18 x 7/8"
Nut 5/16" - 18
Lockwasher 5/16"
Figure 2
Bracket
(Not Supplied)
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
— FINISHED CEILING —
Lag Screws
5/16"x1-7/8"
CONTROL
CENTER
Preferred Range of
Bracket Placement
Hidden
Support
(Not Supplied)
5/16"-18x7/8" Screw
5/16" Lock Washer
5/16"-18 Nut
16
Page 17
Installation Step 7
To
Door
Control
To
Sensors
Terminal
Screws
Control
Center
Install the Door Control and Connect all Wiring
Install Door Control
Locate the door control within sight of the door at a
minimum height of 5 feet where small children cannot
reach, and away from all moving parts of the door and
door hardware.
1. Strip 1/4" of insulation from one end of the bell wire
and connect it to the two screw terminals on the back
of the door control by color: white to 2 and white/red
to 1 (see Figure 1).
2. Fasten the Lighted Door Control Button securely with
6ABx1-1/2" screws. The Multi-Function Door Control
uses 6ABx1" screws. If installing into drywall, drill
5/32" holes and use the anchors provided.
3. Run the bell wire up the wall and across the ceiling to
the opener. Use insulated staples to secure the wire in
several places. Be careful not to pierce the wire with a
staple, creating a short. If your access door is near the
garage door, you may run this wire with the Safety
Reversing Sensor wires along the top of the rail. See
page 14.
4. Remove the Control Center door on the right panel of
the opener to access the terminal screws.
Connect Door Control and Sensor Wiring
5. Thread all wires through the opening at the base of the
drive shaft cover (see Figure 2).
6. Insert the remaining wire through the hole in the power
unit and strip 1/4" of insulation from each set of wires.
7. Connect the door control wire to the opener terminal
screws: white to 2 and white/red to 1. (See Figure 3.)
8. Separate the sensor white and white/black wires
sufficiently to connect to the opener terminal screws:
white to 2 and white/black to 3.
9. Attach the User Safety Instruction label to the wall
near the door control, and the Maintenance Instruction
label in a prominent location on the inside of the
garage door.
Page 28 explains how to operate the opener using the
door controls and the Lock & Light features available
on the Multi-Function Door Control Panel.
Outside Keylock Connections (see Accessories)
To opener terminal screws: white to 2; white/red to 1
Hardware Shown Actual Size
6AB x 1" Screw
Multi-Function Door Control
WARNING
Children operating or playing with a garage door opener
can injure themselves or others.
close and cause serious injury or death.
control (or any additional push buttons) out of the reach
of children and away from all moving parts of the door
and door hardware,
but where the garage door is visible.
Do not allow children to operate the push button(s) or the
remote control transmitter(s).
A moving garage door could injure someone under it.
Activate the opener only when the door is properly
adjusted, you can see it clearly, and there are no
obstructions to door travel.
Do NOT connect the power and operate the opener at
this time. The trolley will travel to the full open
position but will not return to the close position
until the sensor beam is connected and properly
aligned. See Step 9 on page 18.
2-Conductor
Bell Wire
WHT
2
RED
Lighted
1
Figure 1
Door
Control
Terminal
Screws
Figure 2 WIRING TO CONTROL CENTER
Door Control
Connections
(dotted line)
The garage door could
Install the door
Multi-Function
Door Control Panel
Terminal Screws
RED
WHITE
1
2
Insert wires
through
opening in
Drive Shaft Cover
Push wiring
through hole in chassis
(above Control Center)
and connect to opener
terminal screws
Sensor
Connections
6ABx1-1/2" Screw
Lighted Door Control Button
Insulated
Staples
Dry Wall
Anchors
Figure 3
17
1
OPENER TERMINAL SCREWS
2
(In Control Center)
3
Page 18
Installation Step 8
Electrical Requirements
To reduce the risk of electric shock, your garage door
opener has a grounding type plug with a third grounding
pin. This plug will only fit into a grounding type outlet.
If the plug doesn't fit into the outlet you have, contact a
qualified electrician to install the proper outlet.
To avoid installation difficulties,
do not run the opener until Step 9 below.
WARNING
To prevent electrocution or fire,
must be in compliance with local electrical and building
codes.
Do NOT use an extension cord, 2-wire adapter, or change
the plug in any way to make it fit your outlet.
installation and wiring
•If permanent wiring is required by your local code,
refer to the following procedure:
WARNING
To prevent electrocution,
garage door opener
use for the permanent connection.
To make a permanent connection through the 7/8" diam.
hole in the top of the opener (according to local code):
• Remove the opener cover screws and set the cover aside.
• Remove the attached 3-prong cord.
• Connect the black (line) wire to the screw on the brass
terminal; the white (neutral) wire to the screw on the
silver terminal; and the ground wire to the green
ground screw. The opener must be grounded.
• Reinstall the cover.
remove power from the
and
from the circuit you plan to
Right
Permanent Wiring
Connection
Ground Tab
Green
Ground Screw
Ground Wire
Wrong
White Wire
Black
Wire
BlackWire
Installation Step 9
Complete Safety Reversing Sensor Installation
• Plug in the opener. If your door control has a Lock
feature, be sure it is off . Green indicator lights in both the
sending and receiving eyes will glow steadily if wiring
connections and alignment are correct. If the indicator
light is off in the receiving eye (and the invisible light
beam path is not obstructed), alignment is required.
• Loosen the receiving eye wing nut to allow slight
rotation of unit. Adjust sensor vertically and/or
horizontally until the green indicator light glows with a
steady light.
• When indicator lights are glowing steadily in both units,
tighten the wing nut in the receiving eye unit.
Trouble Shooting
1. If the sending eye indicator light does not glow
steadily after installation, check for:
• Electric power to the opener.
• A short in the white or white/black wires. These can
occur under staples or at screw terminal connections.
• Incorrect wiring between sensors and opener.
• An open wire (wire break).
2. If the sending eye indicator light glows steadily but
the receiving eye indicator light doesn't:
• Check alignment.
• Check for an open wire to the receiving eye.
18
Page 19
Installation Step 10
Install the Lights and Lens
• Install a 100 watt maximum light bulb in each socket.
The lights will turn ON and remain lit for
approximately 4-1/2 minutes when power is connected.
Then the lights will turn OFF.
• Insert bottom lens tabs into slots on chassis and tilt
towards chassis to engage top tabs, then drop down
gently into place. (See illustration.)
• To remove, lift lens up and gently tilt slightly outward
and down, then pull out to clear bulbs. Use care to
avoid snapping off bottom lens tabs.
• If the bulbs burn out prematurely, replace with standard
neck Garage Door Opener bulbs. (Fluorescent bulbs are
not recommended because of possible interference with
receiver/transmitter signals.)
Light Socket
CONTROL
CENTER
Bottom Lens Slot
Bottom Lens Tab
CONTROL
CENTER
100 Watt Max.
Light Bulb
Top Lens Slot
Top Lens Tab
Lens
Installation Step 11
Attach the Manual Release Rope and Handle
Trolley
Trolley
Release Arm
Overhand
NOTICE
Knot
Rope
Release Handle
Manual
Overhand
Knot
Chassis
Insert Bottom Lens Tabs First
WARNING
Do not use the red handle to pull the door open or
closed.
could fall.
trolley and, if possible, only when the door is closed.
Garage doors are heavy. If the door is open when the
handle is pulled, the door could close inadvertently if it is
not properly balanced. Serious injury may result to
persons under the door. Make sure the doorway is clear
of persons and obstructions before pulling handle when
door is open.
• Thread one end of the rope through the hole in the top
of the red handle so “NOTICE” reads right side up as
shown. Secure with an overhand knot.
The knot should be at least 1" from the end of the
rope to prevent slipping.
• Thread the other end of the rope through the hole in the
release arm of the outer trolley.
• Adjust rope length so the handle is 6 feet above the
floor. Secure with an overhand knot .
If it is necessary to cut the rope, heat seal the cut end
with a match or lighter to prevent unraveling.
The rope knot could become untied and you
Use the manual release only to disengage the
19
Page 20
Installation Step 12
A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should cover the
height of the top panel.
The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of angle iron
are used to create a U-shaped support. The best solution is to check with your garage door manufacturer for an
opener installation door reinforcement kit.
SECTIONAL Door Installation Procedure
Figure 1
Figure 2
Hardware Shown Actual Size
Fasten Door Bracket
Follow instructions which apply to your door type
as illustrated below or on page 21.
To prevent dama ge to steel, alumin um, fiber glass or
glass panel doors, always reinforce the inside of the door
both vertically and horizontally with an angle iron.
• Center the door bracket on the previously marked
vertical guideline used for the header bracket
installation.
stamped inside the bracket.
• Position the bracket on the face of the door within the
following limits:
A) The top edge of the bracket 2-4" below the top edge
of the door.
B) The top edge of the bracket directly below any
structural support across the top of the door.
• Mark and drill 5/16" left and right fastening holes.
Secure the bracket as shown in Figure 1 if there is
vertical reinforcement.
If your installation doesn't require vertical reinforcement
but does need top and bottom fastening holes for the door
bracket, fasten as shown in Figure 2.
Note the correct UP placement, as
20
Page 21
All ONE-PIECE Door Installation Procedure
• Center the bracket on the top of the door, in line with
the header bracket as shown. Mark holes.
• Drill 5/16" pilot holes and fasten the door bracket with
hardware supplied.
If the door has no exposed framing, drill 3/16" pilot holes
and fasten the bracket with 5/16"x1-1/2" lag screws (not
supplied) to the top of the door.
The door bracket may be installed on the top edge of
the door if required for your installation. (Refer to the
dotted line optional placement drawing.) Drill 3/16"
pilot holes and substitute 5/16"x1-1/2" lag screws (not
supplied) to fasten the bracket to the door.
21
Please read and comply with the warnings and reinforcement instructions on page 20. They apply
to one-piece doors also.
Hardware Shown Actual Size
Page 22
Installation Step 13
Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the
inner trolley. Slide the outer trolley back (away from the door) about 2" as shown in Figures 1, 2 and 3.
Figure 2:
•
Figure 1:
• Fasten straight door arm section to outer trolley with
the 5/16"x1" clevis pin. Secure the connection with a
ring fastener.
• Fasten curved section to the door bracket in the same
way, using the 5/16"x1-1/4" clevis pin.
Figure 1
Figure 2
Figure 3
SECTIONAL Doors Only
Hardware Shown Actual Size
Hole Alignment Alternative
Connect Door Arm to Trolley
Follow instructions which apply to your door type
as illustrated below and on page 23.
Bring arm sections together. Find two pairs of holes
that line up and join sections. Select holes as far apart
as possible to increase door arm rigidity.
Figure 3:
• If holes in curved arm are
disconnect straight arm. Cut about 6" from the solid
end. Reconnect to trolley with cut end down as shown.
• Bring arm sections together.
• Find two pairs of holes that line up and join with
screws, lock washers and nuts.
above holes in straight arm,
Proceed to Adjustment Step 1, page 24.
Trolley will re-engage automatically when the
opener is operated.
22
Page 23
All ONE-PIECE Doors
Assemble the Door Arm:
• Fasten the straight and curved door arm sections
together to the longest possible length (with a 2 or 3
hole overlap).
• With the door closed, connect the straight door arm
section to the door bracket with the 5/16"x1-1/4"
clevis pin.
• Secure with a ring fastener.
On one-piece doors, before connecting the door arm to the trolley the travel limits must be adjusted. Limit adjustment
screws are located on the right side panel as shown on page 24. Follow adjustment procedures below.
Adjustment Procedures for One-Piece Doors
Open Door Adjustment:
Decrease UP Travel Limit
• Turn the UP limit adjustment screw counter-clockwise
5 1/2 turns.
• Press the Door Control push bar. The trolley will
travel to the fully open position.
• Manually raise the door to the open position (parallel
to the floor), and lift the door arm to the trolley. The
arm should touch the trolley just in back of the door
arm connector hole. Refer to the fully open
trolley/door arm positions in the illustration. If the arm
does not extend far enough, adjust the limit further.
One full turn equals 2" of trolley travel.
Closed Door Adjustment:
Decrease DOWN Travel Limit
• Turn the DOWN limit adjustment screw clockwise
5 complete turns.
• Press the Door Control push bar. The trolley will travel
to the fully closed position.
• Manually close the door and lift the door arm to the
trolley. The arm should touch the trolley just ahead of
the door arm connector hole. Refer to the fully closed
trolley/door arm positions in the illustration. If the arm
is behind the connector hole, adjust the limit further.
One full turn equals 2" of trolley travel.
Connect the Door Arm to the Trolley:
• Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. It may be
necessary to lift the door slightly to make the connection.
• Secure with a ring fastener.
• Run the opener through a complete travel cycle. If the door has a slight "backward" slant in full open position as shown
in the illustration, decrease the UP limit until the door is parallel to the floor.
23
Page 24
Adjustment Section: Pages 24 – 26
Adjustment Step 1
Adjust the UP and DOWN Limits
Do not make any limit adjustments until the safety
reversing sensors are completely installed.
Limit adjustment settings regulate the points at which the
door will stop when moving up or down.
The door will stop in the up direction if anything
interferes with door travel. The door will reverse in the
down direction if anything interferes with the door travel
(including binding or unbalanced doors).
To operate the opener, press the Door Control push bar or
button. Run the opener through a complete travel cycle.
• Does the door open and close completely?
• Does the door stay closed and not reverse
unintentionally when fully closed?
If your door passes both of these tests, no limit
adjustments are necessary unless the reversing test fails
(see page 26).
Adjustment procedures are outlined below. Run the
opener through a complete travel cycle after each
adjustment.
Repeated operation of the opener during adjustment
procedures may cause the motor to overheat and shut
off. Simply wait 15 minutes and try again.
Read the procedures carefully before proceeding to
Adjustment Step 2. Use a screwdriver to make limit
adjustments.
WARNING
Improper adjustment of the travel limits will interfere with
the proper operation of the safety reverse system.
door might not reverse properly when required and could
seriously injure or kill someone under it.
Test the safety
reverse system monthly, and following all adjustments to
the travel limits. See page 26.
+
321
8
8
1
1
7
7
3
3
5
5
+
Kg
Kg
Right Side Panel
LIMIT ADJUSTMENT
LABEL
+
+
Adjust UP Travel
Adjust DOWN Travel
The
Travel Limit
Adjustment
Screws
How and When to Adjust the Limits
If the door does not open completely but opens at least
five feet:
Increase up travel. Turn the UP limit adjustment screw
clockwise. One turn equals 2" of travel.
If door does not open at least 5 feet: Adjust the UP
(open) force as explained in Adjustment Step 2.
If the door does not close completely:
Increase down travel. Turn the DOWN limit adjustment
screw counterclockwise. One turn equals 2" of travel.
If door still won't close completely, try lengthening the
door arm. (Page 22.)
If you have adjusted the door arm to the maximum length
and the door still will not close completely, lower the
header bracket. See Installation Step 1, pages 8/9.
If the opener reverses in fully closed position:
Decrease down travel. Turn the DOWN limit adjustment
screw clockwise. One turn equals 2" of travel.
If the door reverses when closing and there is no
visible interference to travel cycle:
If the opener lights are flashing, the Safety Reversing
Sensor is obstructed. Remove the obstruction.
Test the door for binding: Pull the manual release handle.
Manually open and close the door. If the door is binding,
call for garage door service. If the door is not binding or
unbalanced, adjust the DOWN (close) force. See
Adjustment Step 2.
24
Page 25
Adjustment Step 2
Adjust the Force
Force adjustment controls are located on the right panel
of the opener. Force adjustment settings regulate the
amount of power required to open and close the door.
The door will stop in the up direction if anything
interferes with its travel. The door will reverse in the
down direction if anything interferes with its travel
(including binding or unbalanced doors).
If the forces are set too light, door travel may be
interrupted by nuisance reversals in the down direction
and stops in the up direction. Weather conditions can
affect the door movement, so occasional adjustment may
be needed.
The maximum force adjustment range is about 3/4 of a
complete turn. Do not force controls beyond that point.
Turn force adjustment controls with a screwdriver.
8
7
5
Kg
8
1
7
3
1
3
5
Kg
WARNING
Too much force on the door will interfere with the proper
operation of the safety reverse system.
not reverse properly when required and could seriously
injure or kill someone under it.
Do not increase the force
beyond the minimum amount required to close the door.
Do not use the force adjustments to compensate for a
binding or sticking garage door. Test the safety reverse
system monthly, and following all adjustments to force
levels. See page 26.
+
321
8
8
1
1
7
7
3
3
5
5
Kg
Kg
+
The door might
Force Adjustment Label
How and When to Adjust the Forces
Test the DOWN (close) force
Grasp the door bottom when the door is about halfway
through DOWN (close) travel. The door should reverse.
Reversal halfway through down travel does not
guarantee reversal on a one-inch obstruction. See
page 26. If the door is hard to hold or doesn't reverse,
decrease the DOWN (close) force by turning the control
counterclockwise.
Make small adjustments until the door reverses normally.
After each adjustment, run the opener through a complete
cycle.
Test the UP (open) force
Grasp the door bottom when the door is about halfway
through UP (open) travel. The door should stop. If the
door is hard to hold or doesn't stop, decrease UP (open)
force by turning the control counterclockwise.
Make small adjustments until the door stops easily. After
each adjustment, run the opener through a complete
travel cycle.
Right Side
Panel
Force Adjustment
Controls
If the door doesn't open at least 5 feet:
Increase UP (Open) force by turning the control
clockwise. Make small adjustments until door opens
completely. Readjust the UP limit if necessary. After each
adjustment, run the opener through a complete travel
cycle.
If the door reverses during the down (close) cycle and
the opener lights aren't flashing:
Increase DOWN (close) force by turning the control
clockwise. Make small adjustments until the door
completes a close cycle. After each adjustment, run the
opener through a complete travel cycle. Do not increase
the force beyond the minimum amount required to
close the door.
25
Page 26
Adjustment Step 3
Test The Protector System
• Press the remote control push button to open the door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the door.
The door will not move more than an inch, and the
opener light will flash for 5 seconds.
Professional service is required if the opener closes the
door when the safety reversing sensor is obstructed.
The garage door opener will not close from a remote if
the indicator light in either sensor is off (alerting you
to the fact that the sensor is misaligned or obstructed).
The garage door can be closed by pressing and holding
the Door Control push bar or button until down travel is
completed.
®
WARNING
Without a properly working safety reversing sensor,
persons (particularly children) could be seriously injured
or killed if trapped by a closing garage door.
test once a month.
Repeat this
Adjustment Step 4
Test the Safety Reverse System
Test
• Place a one-inch board (or a 2x4 laid flat) on the floor,
centered under the garage door.
• Operate the door in the down direction. The door must
reverse on striking the obstruction.
Adjustment
If the door stops on the obstruction, it is not traveling far
enough in the down direction.
• Increase the DOWN limit by turning the DOWN limit
adjustment screw counterclockwise 1/4 turn.
• Repeat the test.
On a sectional door, make sure limit adjustments do
not force the door arm beyond a straight up and down
position. See the illustration on page 22.
• When the door reverses on the one-inch board, remove
the obstruction and run the opener through 3 or 4
complete travel cycles to test adjustment.
If the door will not reverse after repeated adjustment
attempts, call for professional garage door service.
Important Safety Check
Repeat Adjustment Steps 1-4 after:
• Each adjustment of door arm length, force controls or
limit controls.
• Any repair to or adjustment of the garage door
(including springs and hardware).
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
Safety Reversing Sensor
Safety Reversing Sensor
WARNING
Failure to test and adjust the safety reverse system may
result in serious injury or death to persons trapped by a
closing garage door.
adjust as needed.
Repeat this test once a month and
One-Inch board (or a 2x4 laid flat)
1 Inch Obstruction
26
Page 27
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
To reduce the risk of severe injury or death to persons:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Do not permit children either to operate or to play with the opener. Keep remote control in a location
inaccessible to children.
3. Operate opener only when the door is in full view and free from any obstruction. Keep the door in sight
until it is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
4. Check safety reversal system monthly. See page 26. The garage door MUST reverse on contact with a one
inch object (or a 2x4 board laid flat) placed on the floor. If an adjustment is made to one of the controls
(either force or limits of travel), the other control may need to be adjusted also, and the safety reversal
system must be checked. Failure to properly adjust the opener may result in severe injury or death.
5. If possible, use the manual release only when the door is in a closed position. Caution should be taken
whenever the disconnect cord is actuated with the door open. Weak or broken springs may cause the door to
fall rapidly, causing injury or death to persons.
6. KEEP GARAGE DOORS PROPERLY BALANCED. See page 3. An improperly balanced door may not
reverse when required, and could result in severe injury or death. Repairs to cables, spring assemblies and
other hardware must be made by a professional garage door person.
7. Disconnect the electric power to the garage door opener before making any r epairs or removing the covers.
SAVE THESE INSTRUCTIONS
Care of Your Opener
Force and Limit Adjustment Controls
8
7
5
Kg
FORCE CONTROLS
8
1
7
3
1
3
5
Kg
LIMIT CONTROLS
Weather conditions may cause some minor changes in
door operation requiring some re-adjustments,
particularly during the first year of operation.
Pages 24 and 25 refer to the limit and force adjustments.
Only a screwdriver is required. Follow the instructions
carefully.
Repeat the safety reverse test (page 26) after any
adjustment of limits or force.
Maintenance Schedule
Once a Month
Manually operate door. If it is unbalanced or binding,
call for professional garage door service.
Check to be sure door opens & closes fully. Adjust
limits and/or force if necessary. (See pages 24 & 25.)
+
+
The Remote Control Transmitter
The opener must learn the code of any new remote
control. Page 29 explains how to program your receiver
and how to erase all codes if required. Self service of
your receiver and remote controls is not recommended. If
service is needed, call the toll-free number listed on the
back page.
The Transmitter Battery
The green test light will glow and the opener will operate
when the remote control is activated, as long as there is
adequate battery power.
If the power indicator light is dim or off, replace the
battery. Also check the test light if transmission range
decreases.
The 12 volt battery should produce power for at least a
year.
Dispose of your old battery properly.
Repeat the safety reverse test. Make any necessary
adjustments (See page 26).
Once a Year
Oil door rollers, bearings and hinges. The opener does
not require additional lubrication. Do not grease the door
tracks.
27
Page 28
Operation of Your Opener
Activate the opener with any of the following:
• The Remote Control Transmitter. Hold push button
down until the door starts to move.
• The Door Control. Hold push bar or button down
until the door starts to move.
• The Outside Keylock or Keyless Entry. (See
Accessories)
When the opener is activated with the safety reversing
sensor installed and correctly aligned:
1. If open, the door will close. If closed, the door will
open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for entry
and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
7. The garage door will reverse in the closing cycle when
the invisible beam is broken. If fully open, the door
will not close when the beam is broken. The sensor
has no effect in the opening cycle.
If the sensor is not installed, or is not aligned correctly,
the door won't close from any remote transmitter. You
can close the door with the Door Control, the Outside
Keylock, or Keyless Entry, however, if you activate them
until down travel is complete. If you release them too
soon, the door will reverse.
The opener lights will blink for 5 seconds when the safety
reversing sensor causes the door to reverse.
Opener Lights will turn on under the following
conditions: When the opener is initially plugged in; when
the power is interrupted; when the opener is activated.
They will turn off automatically after 4-1/2 minutes or
provide constant light when the Light feature is activated.
Bulb size is 100 watts maximum.
WARNING
Weak or broken springs could allow an open door to fall
(either rapidly or unexpectedly), resulting in serious
injury, death or property damage .
manual release rope and handle
fully closed.
To open the door
Trolley
Trolley
ReleaseArm
(in Manual
Disconnect
Position)
NOTICE
manually:
The door should be fully
closed if possible. Pull
down on the manual release
handle (so that the trolley
release arm snaps into a
vertical position) and lift the
door manually. The lockout
Lockout position
(Manual disconnect)
feature prevents the trolley
from reconnecting automatically, and the door can
be raised and lowered
manually as often as
necessary.
To reengage the trolley:
Pull the manual release
handle toward the opener at
a 45° degree angle so that
the trolley release arm is
horizontal. The trolley will
reconnect on the next UP or
DOWN operation, either
manually or by pressing the
Door Control push bar.
If possible, use the
only
when the door is
Manual
Release
Handle
(Pull at 45° angle)
Trolley
Release Arm
NOTICE
To reconnect
Trolley
Operation of the Door Controls
(both are not included with all models)
Lighted Door Control Button;
Lighted Push Bar – Door Control Panel: Press to
open or close the door.
Press again to reverse the door during the closing cycle
or to stop the door while it's opening.
Light Feature – Door Control Panel: Press the Light
button. If the opener light is off, it will turn on.
If the opener light is on, (even in the 4-1/2 minute
automatic cycle) it will turn off.
But if you use the Light button to turn the light(s) on and
then activate the opener, the light(s) will turn off after
4-1/2 minutes.
The Light button will not control the opener lights when
the door is in motion.
Lock Feature – Door Control Panel: The Lock
feature is designed to prevent operation of the door from
remote controls. However, the door will open and close
from the Door Control push bar, the Outside Keylock
and the Keyless Entry Accessories.
To Activate: Press and hold the Lock button for
2 seconds. The push bar light will flash as long as the
Lock feature is on.
To turn off: Press and hold the Lock button again for
2 seconds. The push bar light will stop flashing. The
Lock feature will also turn off whenever the "Smart"
button on the opener panel is activated.
28
Page 29
Page 30
Having a Problem?
Situation Probable Cause & Solution
The opener doesn't
operate from either
the door control or
the remote control:
Opener operates from
the remote control, but
not from the door
control:
The door operates from
the door control, but not
from the remote
control:
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the
fuse box or the circuit breaker . (Some outlets are controlled by a wall switch.)
2. Have you disabled all door locks? Review installation instruction warnings on Page 7.
3. Is there a build-up of ice or snow under the door? The door may be frozen to the ground.
Remove any restriction.
4. The garage door spring may be broken. Have it replaced.
5. Repeated operation may have tripped the overload protector in the motor. Wait
15 minutes. Try again.
1. Is the door control push bar lit? If not, Remove the bell wire from the opener terminal
screws. Short the red and white terminals by touching both terminals at the same time with
a piece of wire. If the opener runs, check for a faulty wire connection at the door control, a
short under the staples, or a broken wire.
2. Are the wiring connections correct? Review Installation Step 7, page 17.
1. If your model has the Lock feature, turn it off.
2. Is the wall push button flashing? Your opener needs to re-learn a remote control code.
Refer to instructions on the opener panel.
3. Does the battery test light glow when the remote control push button is pressed? If not,
replace the battery.
4. Program the receiver to match the remote control code.
5. Repeat the receiver programming procedure with all remote controls.
The remote control has
short range:
Opener noise is
disturbing in living
quarters of home:
The garage door
opens and closes by
itself:
The door doesn't open
completely:
1. Check the battery test light. If the light is dim, replace the battery.
2. Change the location of the remote control in your car.
3. Check to be sure the antenna on the right side panel of opener extends fully.
4. Some installations may have shorter range due to a metal door, foil backed insulation, or
metal garage siding.
If operational noise is a problem because of proximity of the opener to the living quarters, the
Vibration Isolator Kit 41A3263 can be installed. This kit was designed to minimize vibration
to the house and is easy to install.
1. Be sure that all remote control push buttons and battery indicator lights are off.
2. Remove the bell wire from the door control terminals and operate from the remote control
only. If this solves the problem, the door control is faulty (replace), or there is an
intermittent short on the wire between the door control and the opener.
1. If the door has been working properly but now doesn't open all the way, increase the up
force. See page 25.
2. Is something obstructing the door? Remove the obstruction or repair the door.
3. If door opens at least 5 feet, the travel limits may need to be increased. One turn equals
2 inches of travel. See page 24.
Repeat the safety reverse test after the adjustment is complete.
The door stops but
doesn't close
completely:
Review the travel limits adjustment procedures on page 24.
Repeat the safety reverse test after any adjustment of door arm length, close force or down
limit.
30
Page 31
Having a Problem?
Situation Probable Cause & Solution
(continued)
The door opens but
won't close:
The door reverses for no
apparent reason and
opener lights don't
blink:
The door reverses for no
apparent reason and
opener lights blink for
5 seconds after
reversing:
The opener lights… don't turn on:
1. If the opener lights blink, check the safety reversing sensor. See page 18.
2. If the opener lights do not blink and it is a new installation, check the down force. See
Adjustment Step 2, page 25. For an existing installation, see below.
Repeat the safety reverse test after the adjustment is complete.
1. Is something obstructing the door? Pull the manual release handle. Operate the door
manually. If it is unbalanced or binding, call for professional garage door service.
2. Clear any ice or snow from the garage floor area where the door closes.
3. Review the force adjustment procedures on page 25.
4. If door reverses in the fully closed position, decrease the travel limits (page 24).
Repeat the safety reverse test after adjustments to force or travel limits. The need for
occasional adjustment of the force and limit settings is normal. Weather conditions in
particular can affect door travel.
Check the safety reversing sensor. Remove any obstruction or align the receiving eye. See
page 18.
Replace the light bulb(s) (100 watts maximum). Use a standard neck garage door opener bulb
if regular bulb burns out.
don't turn off:
Is the Light feature on? Turn it off.
The opener strains or
maximum force is
needed to operate door:
The opener motor
hums briefly, then
won't work:
The opener won't
operate due to power
failure:
The door may be out of balance or the springs are broken. Close the door and use the manual
release handle to disconnect the trolley. Open and close the door manually. A properly
balanced door will stay in any point of travel while being supported entirely by its springs. If
it does not, disconnect the opener and call for professional garage door service. Do not
increase the force to operate the opener.
1. The garage door springs are broken. See above.
2. If the problem occurs on the first operation of the opener, door may be locked. Disable the
door lock.
Repeat the safety reverse test after the adjustment is complete.
1. Use the manual release handle to disconnect the trolley. The door can be opened and closed
manually. When power is restored, press the Door Control push bar and trolley will
automatically reconnect (unless trolley is in lockout position.) See page 28.
2. The Outside Quick Release accessory (for use on garages with no service door) disconnects
the trolley from outside the garage in case of power failure.
31
Page 32
Page 33
Page 34
Accessories Available For Your Opener
Model 1702LM
Model 60LM
Model 88SD
Model 66LM
Model 58LM
LOCK
LIGHT
Outside Quick Release:
Required for a garage with NO access
door. Enables homeowner to open
garage door manually from outside by
disengaging trolley.
Outside Keylock:
Operates the garage door
automatically from outside when
remote control is not handy.
8 foot Complete Rail:
To allow an 8 foot door to open fully.
Keyless Entry:
Enables homeowner to operate garage
door opener from outside by entering
code on specially designed keyboard.
Multi-Function Door Control Panel:
Provides a Lock Feature which
prevents operation of garage door
opener from portable remotes and a
Light Feature for constant light.
Model 81LM
Model 82LM
Model 83LM
Model 84LM
Model 61LM
“Smart” Remote Control:
Includes visor clip.
2-Channel “Smart” Remote Control:
Includes visor clip.
3-Channel “Smart” Remote Control:
Includes visor clip.
4-Channel “Smart” Remote Control:
Includes visor clip.
Single-Function Standard Size
Remote Control:
Includes visor clip.
Model 742LM
Model 722LM
Plug-In Light Control:
Controls interior lights. Plugs into a
wall receptacle.
Wire-In Light Control:
Controls interior or exterior lights.
Wires into the electrical box like a
dimmer switch.
Model 64LM
Model 99LM
9 0
7 8
5 6
3 4
1 2
Multi-Function Mini Remote
Control:
With key ring & Velcro fastening
strip.
Remote Security Transmitter:
Enables homeowner to operate garage
ENTER
door opener by entering 2, 3, 4, or 5
digit code from backlit keyboard.
Includes visor clip.
34
Page 35
Index
Access Door/Outside Quick Release Accessory.........................................................................................................31, 34
Electrical Safety Warnings......................................................................................................................................7, 18, 27
Garage Door
Testing for balance, binding and sticking.................................................................................................................3, 24, 27
Determining high point of travel:
Sectional door....................................................................................................................................................................8
One-piece door..................................................................................................................................................................9
Disabling existing locks...................................................................................................................................................3, 7
Force controls
Adjustment procedures....................................................................................................................................................25
Problems that might require force adjustments.........................................................................................................30, 31
Safety warnings.........................................................................................................................................................25, 27
Door hardware............................................................................................................................................3, 7, 8, 17, 27, 28
Maintenance .............................................................................................................................................................7, 24-27
Reinforcement requirements....................................................................................................................................5, 20, 21
Removing of all ropes......................................................................................................................................................3, 7
Possible door damage...............................................................................................................................................4, 15, 20
Travel limits
Adjustment procedures..............................................................................................................................................23, 24
Problems that might require limit adjustments .........................................................................................................30, 31
Safety warnings.........................................................................................................................................................24, 27
Manual Release Rope & Handle
Lockout feature .................................................................................................................................................................28
Manual disconnect.......................................................................................................................................................28, 31
Safety warnings.................................................................................................................................................7, 19, 27, 28
Opener Terminals
Door control connections..................................................................................................................................................17
Safety reversing sensor connections .................................................................................................................................17
Outside Keylock accessory connections...........................................................................................................................17
Operational Noise
Vibration noise (isolator kit).............................................................................................................................................30
®
Protector System
Receiver & Remote Controls
Programming the receiver.................................................................................................................................................29
Erasing all codes................................................................................................................................................................29
Safety warning...................................................................................................................................................................29
Problems with remote control transmitter operation.........................................................................................................30
Safety Reverse Test Procedure..........................................................................................................................................26
Testing required.................................................................................................................................................7, 26, 30, 31
Safety reverse system problems
Securing header bracket to wall........................................................................................................................................8
Adjusting travel limits.....................................................................................................................................................24
Applying excessive force on the door.............................................................................................................................25
Buckling or uneven floor...................................................................................................................................................5
.........................................................................................................................................................12, 26
Safety Warnings..........................................................................2, 3, 7, 8, 12, 15, 16, 17, 18, 19, 20, 24, 25, 26, 27, 28, 29
User Instruction Label for Garage Wall......................................................................................................................7, 17
35
Page 36
Loading...