Challenge Xtreme M1G-ZP-250 Instructions Manual

Line Trimmer

Instructions for use - Please keep for future reference

IMPORTANT

1. When using this line trimmer follow the basic
safety precautions, as laid out in this guide, at
all times.

2. Keep all the packaging until you are sure that
the product is operating correctly.

ARG, Retail Group, MK9 2NW 721/8314 , 730/3229

Mains cable

Spool coverLine feed button

Spool holder

Cutting line

Cutting line blade

Upper handle

Lower handle

Lower shaft

Cooling Vents

Motor housing

Guard

Upper shaft

Handle clamp

Cable restraint

Power button

Safety button

Instructions

Your grass trimmer

Instructions

Box contents

• Line Trimmer

• Upper handle

• Lower handle

• Handle bolt

• Trimmer guard

• Instruction booklet

• 2 screws and washers

You may also need:

• A screwdriver

Please check that you have the following apparatus in the box that your line trimmer arrived in:

• Make sure you are familiar with the controls and the proper safe use of the line trimmer.

• Never allow children or people unfamiliar with these instructions to use the line trimmer.

• Make sure all people especially children or pets are at least 6 metres away from the cutting area.

• Thoroughly inspect the area where the line trimmer is to be used and remove all stones, sticks,
wires, bones, string and other foreign objects.

• Before using the line trimmer always inspect it to check the cutting line is not worn or damaged.
Worn or damaged items should be replaced before use.

• Make sure the spool is properly installed and securely fastened. Failure to do this could
cause injury.

• Make sure the guard and handle are securely attached.

• Never use metal cutting elements with the line trimmer.

• If you need to use an extension cable it must be marked as suitable for outdoor use.

• The line trimmer user is responsible for accidents or hazards occurring to other people or
their property.

Model Number M1G-ZP-250
Rated Voltage 230 VAC 50Hz
Input Power 350 Watts
Cable Length 10 m
Weight 2.4 Kg
Cutting Width 250 mm
No load speed 11,000 rpm
Cutting Line 4.5 metres max

Preparation

Product specification

Instructions

Use your Line trimmer safely

• Do not operate the line trimmer barefoot or wearing open sandals, always wear
substantial footwear and long trousers. Do not wear loose fitting clothing.

• Wear safety goggles or glasses and ear protectors when using the line trimmer.
Use a face mask if the work is dusty.

• Do not operate the line trimmer when you are tired, ill or under the influence of alcohol,
drugs or medication.

• Secure long hair so it is above shoulder level to prevent entanglement in any
moving parts.

• Keep all parts of your body away from any moving parts.

• Only use the line trimmer in daylight or good artificial light.

• Avoid using the line trimmer on wet grass.

• When trimming slopes always be sure of your footing.

• Switch the line trimmer on by following the instructions in this booklet.

• Switch off the line trimmer, unplug it and wait it has stopped rotating in the
following instances:

• When crossing surfaces other than grass.

• When transporting the line trimmer to and from the area to be trimmed.

• Whenever you leave the line trimmer.

• Before clearing a blockage.

• Before checking, cleaning or working on the line trimmer.

• After striking a foreign object. Inspect the line trimmer for damage and make repairs
as necessary.

• If the line trimmer starts to vibrate abnormally.

• Never carry the line trimmer by the cable or pull the cable to disconnect from the
mains supply.

• Keep the cable away from sharp edges, oils or heat sources. Do not use the line trimmer
if the cable is damaged.

• While using the line trimmer always walk, never run.

• Only use the manufacturers replacement spools. Do not use any other cutting
attachment.

• Do not use without the guards in place.

• Hold both handles while using the line trimmer and do not raise the cutting head above
waist height. Keep the cutting head below 76cm (30 in) from the ground.

Instructions

1 Loosen the handle bolt then slide the

lower handle over the upper shaft.
You will have to push the handle hard
to get it onto the shaft initially (fig. 4).

2 Tighten the handle bolt so the handle is

secure (fig. 5).

3 You can adjust the height of the lower

handle to suit you once the trimmer is
fully assembled.

Instructions

fig. 4

fig. 5

Using your Line trimmer

Attach the lower handle

1 Push the guard over the spool (fig. 1)

make sure it is against the motor
housing and that the cutting line is not
trapped under the guard.

2 Twist the guard in a clockwise direction

until it won’t go any further (fig. 2).
Make sure the screw holes in the guard
and the motor housing line up and then
screw in the self-tapping screws
provided (fig. 3).

fig. 2

fig. 1

fig. 3

Attach the guard