Challenge Xtreme CXPHT22 Quick Start Manual

Download

Quick Start Guide

Your Safety is most important

22 CC Petrol Hedge Trimmer

CXPHT22

please read these safety rules before you use this machine

General Safety Rules

Read user manual before using the machine

Wear safety goggles to guard your eyes from possible injury

Wear gloves to protect your hands

Wear safety shoes to protect your feet

Wear hearing protection

Note - This quick start guide is intended for experienced users who have already assembled the tool, please refer to the manual for further details

Quick Start Guide

Unpack the Hedge Trimmer

a) Open carton carefully and remove all items b) Ensure you have all items (see above) before you discard the packaging

Starting the Hedge Trimmer

Do you have questions?

We can help

Call Customer Service

Mon-Thur 08:45 am - 5:00 pm

Friday 08:45 am - 3:15 pm

UK: 0151 649 1500

IRELAND: 189 094 6244

Spare Parts also available

Items Included

1 Plug spanner 2 Spanner 3 Mixing Bottle 4 Blade guard

Fuel / Lubrication

a) Mix the fuel in the mixer bottle provided b) Shake the container gently to ensure that

it is properly mixed.

N.B Failure to use the correct oil/fuel mixture will cause the engine to seize

Fuel Mixture is 40:1 (40 parts Fuel to 1 part 2 stroke oil)

Use regular grade unleaded petrol and quality 2 stroke oil

Choke Lever

Fuel Cap / tank

Starter Cord

Primer bubble

Ignition switch

Throttle lever

a) Add the fuel to the hedge trimmer b) Set the choke lever ON c) Secure the throttle lever on d) Push primer 10 times e) Pull starter cord rapidly 4 times f) Switch ignition to “I” (on) g) Pull the starter cord up to 6 more times

NOTE: amount of choke will vary slightly Depending on the external temperature. (Warm = choke off “0”, cold = Choke on “I”)

h) Allow engine to warm up at half throttle for a short time and then push the choke in fully

Operating Instructions Hedge Trimmer

WARNING! PLEASE READ THESE INSTRUCTIONS

BEFORE OPERATING THIS UNIT

KEEP THIS MANUAL FOR FUTURE REFERENCE

EH-Art.-No.: 34.038.42 l.-Nr: 01018

CXPHT

Read and follow the operating instructions and safety information before using for the first time.

Always wear PPE (Personal Protective Equipment).

Wear eye protection!

Wear Ear Protection!

Beware of electrical voltage

Helpline No: UK 0151 649 1500 / IRE 189 094 6244

10 11

12 13

14 15

Helpline No: UK 0151 649 1500 / IRE 189 094 6244

! Important!

When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be found in the enclosed booklet.

! CAUTION!

Read all safety regulations and instructions.

Any errors made in following the safety regulations and instructions may result in an electric shock, fire and/or serious injury.

Keep all safety regulations and instructions in a safe place for future use.

Explanation of the warning signs on the equipment (see Fig. 17)

1. Warning!

2. Read the directions for use before operating the equipment.

3. Do not expose the hedge trimmer to rain or wet conditions.

4. Wear eye protection and ear plugs.

5. Wear safety gloves.

6. Wear sturdy, non-slip footwear.

7. Caution: Sharp blades! Always keep hands and feet away from the blades.

8. Operate and start the equipment only outdoors in well ventilated areas to reduce the danger of injury from toxic gases.

9. Explosive material.

10. Very hot surface. Do not touch the hot exhaust silencer, gearbox or cylinder. You may burn yourself. These parts have become very hot during operation and remain very hot over a long period even after the equipment has been switched off.

11.

Maintain a distance of at least 15 m from other persons

2. Layout and items supplied (Fig. 1-2)

1. Cutting blade

2. Cutting blade safety cover

3. Safety guard

4. Front handle

5. Choke lever

6. ON/OFF switch

7. Lubrication nipple

8. Gears

9. Fuel pump (primer)

10. Air filter cover

11. Starter handle

12. Rear handle

13. Throttle lever “release”

14. Throttle lever

15. Silencer cover

16. Tank for fuel mixture

17. Spark plug boot

18. Spark plug wrench

19. Oil/ Petrol mixing bottle

20. Cutter rail cover

3. Proper use

Important. This hedge trimmer is suitable for cutting

hedges, bushes and shrubs.

Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the equipment is used in commercial, trade or industrial businesses or for equivalent purposes.

The machine is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

4. Technical data

Engine type:

2-stroke engine, air-cooled, chrome cylinder

Engine output (max.): 0.65 kW / 0.9 hp

Displacement: 22 cc

Idle speed of engine: 2850 min

-1

Max. engine speed: 8500 min

-1

Weight (with empty tank): 5.6 kg

Cutting length: 50 cm

Tooth spacing: 28 mm

Vibration (front handle) a

7.63 m/s

Vibration (rear handle) a

5.01 m/s

Sound pressure level L

81 dB

Sound power level L

106 dB

Sound and vibration were measured in accordance with 2000/14/EC.

Helpline No: UK 0151 649 1500 / IRE 189 094 6244

5. Before starting the machine

5.1 Fuel and oil

Recommended fuels

Use only a mixture of normal unleaded petrol and special 2-stroke engine oil. Mix the fuel mixture as indicated on the fuel mixing table.

Please note:

Do not use a fuel mixture which has been

kept for longer than 90 days.

Please note:

Do not use 2-stroke oil with a recommended mixing ration of 100:1. If inadequate lubrication causes engine damage, the manufacturer’s engine warranty will be voided.

Please note:

Only use containers designed and approved for the purpose to transport and store fuel.

Pour the correct quantities of petrol and 2-stroke oil into the mixing bottle (see scale printed on the bottle). Then shake the bottle well.

5.2 Fuel mixture table

Mixing procedure: 40 parts petrol to 1 part oil

6. Operation

Please note that the statutory regulations governing noise abatement may differ from town to town.

6.1 Starting the engine from cold (Fig. 3-5)

Fill the tank with the required amount of oil/petrol mix.

1. Set the machine down on a hard, level surface.

2. Set the choke lever (Fig. 4/Item 5) to “ ”.

3. Press the fuel pump (primer) (Fig. 4/Item 9) 10 times.

4. Set the throttle lever to full throttle. To do so, press

the throttle lock (Fig. 3/Item 13).

5. With the other hand pull out the starter cable (Fig.

5/Item A) until you feel it starts to resist. Now pull the starter cable rapidly 4 times. Important: Never allow the starter cable to snap back. This may damage the equipment.

6. Move the ON/OFF switch (Fig. 3/Item 6) to "l"

Pull the starter cable up to 6 more times.

Note:

amount of choke will vary slightly. Depending on the external temperature. (Warm = Choke Off " ", Cold = Choke On " "

If the engine has started, set the choke lever immediately to " " and allow the machine to warm up for approximately 10 seconds.

9. If the engine does not start up , repeat steps 7 - 8 above.

Please note: If the engine does not start up even after several attempts, read the section “Engine Troubleshooting”.

Please note: Always pull the starter cable out in a straight line. If it is pulled out at an angle, then friction will occur on the eyelet. As a result of this friction, the cable will become frayed and will wear away faster.

6.2 Starting the engine when warm (if the machine has not been switched off for more than 15 – 20 minutes)

1. Set the machine down on a hard, level surface.

2. Switch the ON/OFF switch to “I”.

3. Hold the machine by the front handle in your right hand and pull the starter cable up to the first resistance point (approx. 10 cm). Then tug sharply on the starter cable. The machine should start after 1-2 tugs. If the machine does not start after 6 pulls, repeat steps 1 – 8 of the procedure for starting the engine from cold.

6.3 Switching off the engine

Emergency Stop procedure: If it becomes necessary to stop the machine immediately, set the ON/OFF switch to “Stop” or “0”

Normal procedure: Let go of the throttle lever and wait until the engine has changed to idling speed. Then set the ON/OFF switch to “Stop” or “0”.

6.4 Practical tips

Never allow the machine to run at low speed for starting or for cutting.

Cutting for dense growth: The most effective method is to use wide, sweeping movements, guiding the cutting edge of the blade straight through the branches. A slight incline of the blade downwards towards the movement will produce best cutting results.

It is recommended to tie a guide line of string or the like along the hedge so that you cut the hedge to a level height. The branches above it will be cut off. (Fig. 6)

Cutting the side of a hedge: Cut the sides of the hedge with curve-shaped movements from the bottom up. (Fig. 7)

Please note: As a result of its design, if you work with the machine on its side for a lengthy period and the tank not completely filled, the motor may stall.

Helpline No: UK 0151 649 1500 / IRE 189 094 6244

Petrol

1 liters 5 liters

2-stroke oil

25 ml 125 ml

7. Cleaning, maintenance, storage and ordering of spare parts

7.1 Cleaning

•

Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.

•

We recommend that you clean the device immediately each time you have finished using it.

•

Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device.

7.2 Maintenance

Always switch off the hedge trimmer and remove the spark plug boot (Fig. 13) before carrying out any maintenance work.

1. The cutter blades are high quality, made of tempered steel and in normal use there is no need to sharpen the blades. If you accidentally strike a wire, stone, glass or other hard object, this may cause a notch in the blade. There is no need to remove the notch as long as it does not adversely affect the movement of the cutting edges. If it does adversely affect this movement, switch off the machine and use a fine file or a fine grinding stone to remove the notch. Ensure that the blade’s cutting edge is always well oiled (see Fig. 8).

2. If you drop the hedge trimmer, check whether it has suffered any damage. If it is damaged contact the Argos general enquiries 0845 640 3030.

3. Only clean the machine after it has been switched off. Use only mild soap and a damp cloth to clean it. Never allow fluid to get into the machine. Do not use caustic cleaning products.

7.2.1 Maintenance of the air filter (Fig. 9-11)

Soiled air filters reduce the engine output by supplying too little air to the carburetor.

Regular checks are therefore essential. The air filter should be checked after every 25 hours of use and cleaned if necessary. If the air contains a lot of dust, the air filter should be checked more frequently.

1. Remove the air filter cover (Fig. 9-10)

2. Remove the filter element (Fig. 11)

3. Clean the filter element by tapping it or blowing it.

4. Assemble in reverse order.

Please note: Never clean the air filter with petrol or inflammable solvents. Clean the air filter with compressed air or by tapping it.

7.2.2 Maintenance of the spark plug (Fig. 12-14)

Spark plug gap = 0.025 inch (0.635 mm). Tighten the spark plug with a torque of 12-15 Nm.

Check the spark plug for dirt and grime after 10 hours of operation and if necessary clean it with a copper wire brush. Thereafter service the spark plug after every 50 hours of operation.

1. Pull off the spark plug boot (Fig. 13) by twisting.

2. Remove the spark plug (Fig. 14) with the supplied spark plug wrench.

3. Assemble in reverse order.

7.2.3 Maintenance of the gearbox (Fig. 15)

The gearbox must be lubricated every year before the start of the season at the lubrication nipple (Fig. 15/Item A). Place a conventional grease gun on the nipple and press approx. 3 strokes of conventional machine grease into the gearbox. If you use the trimmer frequently, grease the gearbox more often.

7.2.4 Carburetor settings

Important. Settings on the carburetor may only be made

by authorized customer service personnel. The air filter cover must be removed before any work on the carburetor, as shown in Figures 9 – 10.

Setting the throttle cable:

If the maximum speed of the machine falls over time and you have ruled our all the other causes listed in section 9 Troubleshooting, it may be necessary to adjust the throttle cable.

First of all check whether the carburetor opens fully when the throttle handle is pressed fully. This is the case if the carburetor slide (Fig. 16/Item 1) rests against the stop (Fig. 16/Item 2) when the throttle is fully open. Figure 16 shows the correct setting. If the carburetor slide does not touch the stop, it must be adjusted.

The following work is required to adjust the throttle cable:

•

Undo the lock nut (Fig. 16/Item 3) a few turns.

•

Undo the adjusting screw (Fig. 16/Item 4) until the carburetor slide rests against the stop when the throttle is fully open, as shown in Figure 16.

•

Retighten the lock nut.

Setting the idling speed: Important. Set the idling speed when the machine is warm.

If the engine stalls when the throttle is not pressed and you have ruled out all the other causes listed in section 9 Troubleshooting, the idling speed must be adjusted. To do this turn the idling speed screw (Fig. 16/Item 5) clockwise until the machine runs smoothly at idling speed.

If the idling speed is so fast that the cutting blades do not reach a standstill, the idling speed must be reduced by turning the idling speed screw (Fig. 16/Item 5) counterclockwise until the cutting blades stop.

Helpline No: UK 0151 649 1500 / IRE 189 094 6244

7.3 Storage Please note: If you fail to follow these instructions

correctly, deposits may form on the interior of the carburetor which may result in the engine being more difficult to start or the machine suffering permanent damage.

1. Carry out all the maintenance work.

2. Drain the fuel out of the tank (use a conventional plastic petrol pump from a DIY store for this purpose).

3. When the fuel has been drained, start the engine.

4. Allow the engine to run at idling speed until it stops. This will clean the remainder of the fuel out of the carburetor.

5. Leave the machine to cool (approx. 5 minutes).

6. Remove the spark plug (see point 7.2.2).

7. Place a teaspoon full of 2-stroke engine oil into the combustion chamber. Pull the starter cable several times carefully to wet the internal components with the oil. Fit the spark plug again.

8. Clean the exterior housing of the machine.

9. Store the machine in a cold, dry place where it is out of the reach of ignition sources and inflammable substances.

Fertilizers and other chemical garden products often contain substances that accelerate the rate of corrosion of metals. Do not store the machine on or near fertilizers or other chemicals.

Restarting

1. Remove the spark plug.

2. Pull the starter cable several times to clean the oil residue out of the combustion chamber.

3. Clean the spark plug contacts or fit a new spark plug.

4. Fill the tank. See the section entitled Fuel and oil.

5. Complete steps 1-8 described under the point (6.2) entitled “Starting the engine from cold”.

7.4 Ordering replacement parts

Please quote the following data when ordering replacement parts:

•

Type of machine

•

Article number of the machine

•

Identification number of the machine

•

Replacement part number of the part required

For our latest prices and information please go to www.isc-gmbh.info

8. Disposal and recycling

The unit is supplied in packaging to prevent its being damaged in transit. This packaging is raw material and can therefore be reused or can be returned to the raw material system for recycling.

The unit and its accessories are made of various types of material, such as metal and plastic.

Defective components must be disposed of as special waste. Ask your dealer or your local council.

Helpline No: UK 0151 649 1500 / IRE 189 094 6244

9. Troubleshooting

Problem Cause Solution

The machine does not start. 1. Correct starting procedure not 1. Follow the instructions for starting.

followed.

2. Sooted or damp spark plug 2. Clean the spark plug or replace it with a new one.

3. Incorrect carburetor setting 3. Contact an authorized customer service outlet or contact the Argos general enquiries 0845 640 30 30.

The machine starts but does not 1. Incorrect choke lever setting 1. Set choke lever to develop its full output.

2. Soiled air filter 2. Clean the air filter

3. Incorrect carburetor setting 3. Contact an authorized customer service outlet or contact the Argos general enquiries 0845 640 30 30.

The engine does not run smoothly 1. Incorrect electrode gap on the 1. Clean the spark plug and adjust

spark plug the electrode gap or fit a new

spark plug.

2. Incorrect carburetor setting 2. Contact an authorized customer service outlet or contact the Argos general enquiries 0845 640 30 30.

Engine smokes excessively 1. Incorrect fuel mix 1. Use the correct fuel mix (see fuel

mixing table)

2. Incorrect carburetor setting 2. Contact an authorized customer service outlet or contact the Argos general enquiries 0845 640 30 30.

Helpline No: UK 0151 649 1500 / IRE 189 094 6244

Product Guarantee

This product is guaranteed against manufacturing defects for a period of

1 Year

This does not cover the product where the fault is due to misuse, abuse, use in contravention of

the instructions, or where the product has been the subject of unauthorised modifications or

alterations, or has been the subject of commercial use

In the event of a problem with the product within the guarantee period please return it to your

nearest store

If the item is shown to have had an inherent defect present at the time of sale, the store will

provide you with a replacement

Your statutory rights remain unaffected

Guarantor; Home Retail Group

489 – 499 Avebury Boulevard

Central Milton Keynes

MK9 2NW

Importer; Einhell UK Unit 5 Morpeth Wharf Twelve Quays Birkenhead Wirral CH41 1LF

Helpline No: UK 0151 649 1500 / IRE 189 094 6244 15

Challenge Xtreme CXPHT22 Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual