1
INSTRUCTION MANUAL
MONDEL:TX-TF29CR
1. GENERAL SAFETY INSTRUCTIONS
Read this instruction manual thoroughly before using the appliance and save it for future
reference and if necessary pass the instruction manual to a third party.
WARNING: When using electrical appliance, basic safety precautions should always be
followed to reduce the risk of fire, electrical shock and personal injury.
1) General
Check if the electrical specifications of this appliance are compatible with your installation.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
To protect against electrical hazard, do not immerse in water or other liquids. Do not use
near water.
This appliance is for indoor use only.
Do not place objects on top of the unit.
Do not unplug the unit if your hands are wet, electrical shock could occur.
Do not carry the appliance while it is operating.
Place it on a secure and level area. Keep out of reach of children to prevent any accident.
Unauthorized use and technical modifications to the appliance can lead to danger to life
and health.
Do not push any object into the appliance. Do not disassemble the appliance.
2) Electrical safety
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
2
2. DRAWING.
1. Control Panel
2. Air Outlet
3. Base
3.ASSEMBLING
3
• Unscrew the 3 screws from the template (Picture 1).
• Fix the two parts of the base together (Picture 2). Pass the power cord through the
center hole of the base.
• Align the base and template, and fix the 3 screws using a screwdriver (Picture 3).
• Insert the wire until it reaches the opening at the bottom of the base (Picture 4).
4.OPERATION.
Set the appliance on a dry, level and sturdy surface.
Plug the appliance into the mains.
Note: All controls can be operated from the fan unit or from the remote control.
4
NO/OFF, SPEED SELECTION
1. To turn on the fan, press”ON/SPEED” (A). And press again, the fan will start to operate in
Low/Middle/High speed setting.
2. Continue to press ”ON/SPEED” (A) to select the desired speed.
3. To turn off the fan, press the “OFF”(B) control knob.
OSCILLATION
1. To have oscillation, press oscillation knob “OSC” (D) once on the top of the fan
body.The fan will start oscillation.
2. To stop the oscillation, press oscillation knob “OSC” (D), then the fan will stop
oscillation.
TIMER FUNCTION
1.The fan is equipped with a timer that allows you to set its length of the operation from
0.5h to 7.5h.
2.Press “TIMER” (C) to start the timer mode and continue to press until the desired time is
reached.
3.Each LED indicates a time period.When two or more LED’s are illuminated the time
needs to be added. E.g. 2H and 1H illuminated will give a 3 hour timer.
AIR FLOW SELECTION MODES
1.Normal sets a constant air flow at the currently selected speed.
2.Natural will constantly cycle through high, medium and low speeds.
3.Sleep will constantly cycle through the current selected, and lower than speeds,
reducing by one speed at each 30 minute interval, until low is reached whereby it will
remain on low constantly.
5
BATTERY REPLACEMENT
1.Remove the battery cover from the remote control.
2.Replace with 2 pieces UM-4”AAA”/R03 battery.
3.Carefully close the battery cover.
.
5. MAINTENNANCE/CLEANING
Disconnect from mains before maintenance or cleaning.
Use only a damp cloth to clean the enclosure.
Plastic parts should be cleaned with mild soap and a damp cloth. The fan must be
cleaned thoroughly before storage and covered with plastic bags and stored in a dry
place.
Loading...