N0E-2ET-230
OPERATING INSTRUCTIONS
Cordless Grass Trimmer
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
WARNING!
Read all instructions. Failure to follow all
instructions listed below may result in electric
shock, re and/or serious injury. The term
“power tool” in all warnings listed below refers
to your mains operated power tool.
1. Read the instruction carefully. Be
familiar with the controls and the correct use
of the appliance. Read and understand the
operator’s manual and observe the warnings
and instruction labels afxed to the appliance.
2. Users. Never allow children or people
unfamiliar with these instructions to use the
appliance. Local regulations may restrict the
age of operator. Never operate the tool under
the inuence of alcohol, medication or drugs.
3. Use appropriate tool. This device is only
intended for trimming grass outdoors and only
designated for use on private property. Do not
force small tools or attachments to do the job
of a heavy duty tool.
4. Keep work areas clean. Cluttered areas
can cause accidents.
5. Consider work area environment. Do not
expose the tool to high humidity or rain. Do
not use the tool in damp and wet conditions.
Keep the work area well lit. Do not use the
tool where there is a risk of causing re or
explosion, e.g. in the presence of ammable
liquids and gases.
6. Keep all bystanders, children, and pets
away. The operator or user is responsible for
accidents or hazards occurring to other people
or the property.
7. Dress appropriately. Do not wear loose
clothing or jewelry, as these can be caught in
moving parts. Preferably wear non-slip
GENREARL POWER TOOL
SAFETY WARNINGS
Thank you for purchasing a CHALLENGE
grass trimmer.
We hope you are completely satised with
your new product and hope you will enjoy
using this tool for many years.
Your N0E-2ET-230 Grass Trimmer has been
designed for trimming light foliage and is
intend for DIY use only.
INTRODUCTION
footwear when working outdoors. Wear
protective hair covering to keep long hair out
of the way.
8. Head protection. Always use safety
glasses and gloves. Use a face or dust mask
whenever the operations may produce dust or
ying particles. Wear ear protection whenever
the sound level seems uncomfortable.
9. Do not overreach. Keep proper footing and
balance at all times.
10. Stay alert, watch what you are doing.
Use common sense when operating the
appliance. Do not operate the tool when you
are tired.
11. Grip the tool securely. Operator should
have one hand on the main handle, the other
on the front handle. Keep nger off trigger until
ready to use.
12. Remove adjusting keys and wrenches.
Always check that adjusting keys and
wrenches are removed from the tool before
operating the tool.
13. Risk of cut. Do not touch or try to stop the
nylon line when it is rotating.
14. Disconnect the battery. Disconnect
battery from the tool when not in use or when
servicing or cleaning.
15. Check for damaged parts. Before further
use, carefully check the tool for damage.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting
and any other condition that may affect its
operation.
Do not use the tool if any parts are damaged
or defective. Have any damaged or defective
parts repaired or replaced by an authorized
service agent. Never attempt any repairs
yourself.
16. Store idle tools. When not in use, tools
should be stored in a dry, locked-up place out
of reach of children.
17. Maintain tools with care. Keep tools
clean and in good condition for better and
safer performance. Follow the instructions for
maintenance and changing accessories. Keep
handles and switches dry, clean and free from
oil and grease.
18. Have your tool repaired by an
authorized service agent. This tool is
manufactured in accordance with the relevant
safety regulations. To avoid danger, electrical
appliances must only be repaired by qualied
technicians.
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
WARNING!
Do not use any attachments or accessories not
recommended by the manufacturer of this tool.
The use of attachments or accessories not
recommended can result in serious personal
injury.
Environmental Protection Agency. Before
disposing of damaged or worn out NickelCadmium battery packs, check with your
local Environmental Protection Agency to nd
out about special restrictions on the disposal
of these battery packs or return them to a
certied service center for recycling.
Chargers
1. Charger’s plug must match the outlet. Never
modify the plug in any way. Unmodied plugs
and matching outlets will reduce risk of electric
shock.
2. Use your charger only to charge batteries
of the type supplied with your tool. Other
batteries could burst, causing personal injury
and damage.
3. Only 2 battery packs are allowed to be
charged continuously in order to prevent
overheating of charger, necessary rest time is
required to let the charger cool down before
further charging.
4. When charging is nished, unplug the
charger from mains socket outlet and take
away the battery pack from the charger, do not
leave the battery pack in the charger.
5. Never carry the charger by its cord or pull it
to disconnect from the socket. Keep the cord
away from heat, oil and sharp edges.
6. Never attempt to charge non-rechargeable
batteries.
7. The cord of the charger is not changeable,
do not continue to use if the cord is damaged.
8. Do not expose to water or rain, do not use
in wet condition.
9. Do not open the charger.
10. Do not probe the charger.
11. Intended for indoor use only.
ADDITIONAL SAFETY
INSTRUCTIONS FOR
BATTERIES AND
CHARGERS
Batteries
1. Never attempt to open for any reason.
2. Do not expose to water.
3. Do not incinerate the battery pack even if
it is severely damaged or is completely worn
out. The battery pack can explode in a re.
4. Do not store in locations where the
temperature may exceed 40oC.
5. Do not leave the battery pack in the charger
when the charging is nished, otherwise
battery leakage may occur.
6. Charge only at room temperature.
7. Charge only by using the charger provided
with the tool (see technical data).
8. Before charging, make sure that the battery
is dry and clean.
9. Use only the correct type of battery for the
tool (see technical data).
10. When dispose of batteries follow the
instructions given in the section "protecting the
environment".
11. Under extreme conditions, battery leakage
may occur. When you notice liquid on the
battery, proceed as follows:
---Carefully wipe the liquid off using a cloth.
Avoid skin contact.
---In case of skin or eye contact, follow the
instructions below.
---The battery uid, a 25-30% solution of
potassium hydroxide, can be harmful. In case
of skin contact, immediately rinse with water.
Neutralize with a mild acid such as lemon
juice or vinegar. In case of eye contact, rinse
abundantly with clean water for at least 10
minutes. Consult a physician.
NOTE: the batteries in your battery charger
are the nickel-cadmium type. Cadmium is
considered to be a toxic material by the
ADDITIONAL SAFETY
INSTRUCTIONS FOR
GRASS TRIMMERS
1. Wear safety goggles when operating this
tool.
2. Wear gloves when operating this tool.
3. Do not expose the tool to rain or high
humidity.
4. Be familiar with the controls and proper use
of trimmer.
5. Never allow children or people unfamiliar
with the instructions to use the trimmer.
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
6. Keep children, other people and pets away
from the trimmer; the grass which is cut and
dispersed may contain stones and debris. Stop
using the trimmer while people, especially
children, or pets are nearby.
7. Do not let other people or animals come
within 15 feet of the trimmer when in use.
8. Only use the trimmer in daylight or good
articial light.
9. Before using the trimmer and after any
impact, check for signs of wear or damage and
repair as necessary; Do not use the trimmer if
the cutting device is not secured properly or is
damaged.
10. Always check the good working order
of the trimmer which, if not adequate, could
endanger the user.
11. Never operate the trimmer with damaged
guards or without the guards in place.
12. Before starting the trimmer, make sure that
the nylon line is not touching stones or debris.
13. Keep hands and feet away from the
cutting means at all times and especially when
switching on the motor.
14. Take care against injury from the cutter
blade tted for trimming the lament line
length. After extending new cutter line always
return the trimmer to its normal operating
position before switching on.
15. Never t metal cutting elements.
16. Never use replacement parts or
accessories not provided or recommended by
the manufacturer.
17. Remove the battery before checking,
cleaning or working on the trimmer and when it
is not in use.
18. Always ensure that ventilation openings
are kept clear of debris.
19. To avoid unintentional starting, do not carry
the machine with a nger on the on/off switch.
20. Remain in a stable and secure position
while operating the trimmer.
21. Keep the area being cut free from wires,
stones and debris.
22. Do not cut against hard objects. This could
cause injury or damage the trimmer.
23. Warning! Cutting elements continue to
rotate after the motor is switched off.
24. Do not try stopping the cutting device (nylon
line) with your hands. Always let it come to a
stop by itself.
25. Do not use the trimmer to cut grass which
is not in contact with the ground; for example
do not cut grass which is on walls or rocks etc.
26. Do not cross roads or gravel paths with the
trimmer still running.
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
SYMBOLS
Symbols are used in this manual to attract your
attention to possible risks. The safety symbols
and the explications which accompany them
must be perfectly understood. The warning
themselves do not prevent the risks and can
not be a substitute for proper methods of
avoiding accidents.
Ni-Cd
Before any use, refer to the
corresponding paragraph in the
present manual.
Warning!
Wear ear protection.
Wear eye protection.
Wear dust mask.
Do not expose to rain.
Keep bystanders away.
Do not dispose of batteries in rivers
or immerse in water.
Do not dispose of batteries in a re.
They will explode and cause injury.
Contains NI-CD battery. Battery
must be recycles or disposed of
properly.
Do not dipose of batteries. Return
exhausted batteries to your local
collection or recycling point.
Waste electrical products should not be
disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice.
Ni-Cd
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1. Charger
2. Battery Pack
3. Charger Base
4. Green LED (Indicates Power On)
5. Red LED (Indicates Tool is Charging)
6. Switch Lock
7. On/Off Switch
8. Front Handle
9. Front handle knob
10. Telescopic tube
11. Height Adjustment Knob
12. Motor Housing
13. Protection Guard
14. Line Blade
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
WARNING!
The charger and battery pack are specically
designed to work together so do not attempt
to use any other devices. Never insert or allow
metallic objects into your charger or battery
pack connections because an electrical failure
and hazard will occur.
The battery needs to be charged before rst
use and whenever it fails to produce sufcient
power on jobs that were easily done before.
When charging the battery for the rst time,
or after prolonged storage, it will only accept
an 80% charge. After several charge and
discharge cycles, the battery will attain full
capacity. The battery may become warm while
charging, and this is normal and does not
indicate a problem.
A
Remove the battery from the tool and insert
it into the charge base (3). The battery pack
will only t into the charge in one way. Do not
force. Be sure that battery is fully seated in the
charger base.
1. Charging procedure
These chargers require no adjustment and are
designed to be as easy as possible to operate.
Simply place your battery pack into the
CHARGING THE BATTERY
(FIG. A)
Note: Before using the tool, read the
instruction book carefully.
OPERATION
INSTRUCTIONS
receptacle of a plugged in charger and it will
automatically charge the pack.
1). Connect the transformer (1) to the charger
base (3).
2). Plug the transformer into an appropriate
AC power outlet. The green LED (POWER) (5)
lights to tell you that the charger is ready for
use.
3). Insert the battery pack (2) into the charger,
as shown in Fig A, making sure the pack
is fully seated in the charger. The red LED
(CHARGE) (4) lights to tell you that the battery
pack is on charge.
4). The battery pack will be fully charged in
about 3-5 hours, and the red LED will be off.
2. Important charging notes
Longest life and best performance can be
obtained if the battery pack is charged when
the air temperature is between 18-24
o
C. Do
not charge the battery pack in a very low or
very high air temperature. This is important
and will prevent serious damage to the battery
pack.
1). The charger and battery pack may become
warm to touch while charging. This is a normal
condition, and does not indicate a problem.
2). Use the charger in normal room
temperatures whenever possible. To prevent
overheating, do not cover the charger and do
not charge battery packs in direct sunlight or
near heat sources.
3). If the battery pack does not charge
properly:
a) Check current at receptacle by plugging in
a lamp or other appliance.
b) Move charger and battery pack to a location
where the surrounding air temperature is
approximately 18-24oC.
c) If charging problems persist, take or send
the tool, battery pack and charger to your local
service center.
4). The battery pack should be recharged
when it fails to produce sufcient power
on jobs which were easily done previously.
DO NOT CONTINUE to use under these
conditions. Follow the charging procedure.
You may also charge a partially used pack
whenever you desire with no adverse affect on
the battery pack.
5). Under certain conditions, with the charger
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
B
Your grass trimmer is equipped with a battery
pack, which powers the unit.
1. To t battery pack
1). Place battery pack in your grass trimmer.
Align raised rib on battery pack with groove
inside grass trimmer. See Figure B.
2). Make sure the latches on each side of your
battery pack snap in place and the battery
pack is secured in grass trimmer before
beginning operation.
2. To remove battery pack
1). Locate latches on end of battery pack and
depress to release battery pack from your
grass trimmer.
2). Remove battery pack from your grass
trimmer.
plugged in to the power supply, the exposed
charging contacts inside the charger can be
shorted by foreign material. Foreign materials
of a conductive nature such as, but not limited
to, steel wool, aluminum foil, or any buildup
of metallic particles should be kept away
from charger cavities. Always unplug the
charger from the power supply when there is
no battery pack in the cavity. Unplug charger
before attempting to clean.
6). Do not immerse charger in water or any
other liquid.
WARNING!
Don’t allow any liquid to get inside charger.
Electric shock may result. To facilitate the
cooling of the battery pack after use, avoid
placing the charger or battery pack in a warm
environment such as in a metal shed, or an
uninsulated trailer.
CAUTION!
Never attempt to open the battery pack for any
reason. If the plastic housing of the battery
pack breaks or cracks, return to a service
center for recycling; do not put it into further
use.
NOTE: When the charging is nished, do not
leave your battery on charge continuously. this
may damage the battery cells. If the battery
pack is very hot you must allow it to cool rst
to ambient temperature and then recharging
can be started. If you charge a second battery
pack immediately after the rst one, then the
charger adapter can be overheated. Always
allow at least 15 minutes rest between battery
pack charging.
WARNING!
NEVER TO LEAVE THE BATTERY
AND CHARGER UNATTENDED WHEN
CHARGING THE BATTERY.
WARNING!
TO AVOID THE SHORT CIRCUIT OF THE
BATTERY PACK, DON’T TOUCH THE
BATTERY TERMINALS WITH RINGS AND
OTHER METALLIC OBJECTS.
1
2
3
4
5
TO REMOVE OR INSTALL
BATTERY PACK (FIG. B)
WARNING!
Before assembly, remove the battery pack
from the tool.
RELEASE BUTTON
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
1. Guard installation(FIG. C1, C2)
1). Remove two screws and washers from the
guard.
2). Position the motor housing with string head
carrier facing up.(Figure C1)
3). Slide guard over motor housing.(Figure C1)
4). Install two washers 1 in the correct position.
(Figure C2)
5). Re-insert the screws 2 through the trimmer
head and into the guard and tighten as shown
in gure C2.
C1 C2
2. Attach front handle (FIG. D)
1). Insert the handle in comfortable position
and lightly tighten.
2). Before tightening completely, adjust the
front handle height by sliding handle up or
down tube. When front handle is at desired
operating height, tighten nut securely.
D
ASSEMBLY INSTRUCTIONS OPERATION(FIG. E)
Grip rear handle and press trigger lock-off
button (A) with thumb then pull trigger switch (B).
(See Figure E)
E
STARTING
1. When starting the lawn trimmer for the rst
time, check that the nylon lines touch or pass
over the wire cutting blade. If they are not long
enough,
1). press the button
2). pull more nylon wire to lengthen.(Figure F1)
2. The lengthened nylon line will be cut to size
automatically by the wire cutting blade once the
string trimmer is turned on.
3. During use, the nylon line will become
shortened or worn. To automatically lengthen
or advance the nylon cutting line, tap the
spool button lightly on ground (while the unit is
running).(Figure F2)
F1 F2
4. The length of the grass trimmer can be
innitely varied and therefore adjusted to your
individual height (Figure G):
1). Hold the tube with one hand, then loosen
the height adjustment knob.
2).Set the handle to the correct length and
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
I
5. Making sure to insert the spring, assemble
the spool and spool carrier back onto the
trimmer. To do so, push the head on and turn it
clockwise until it locks. You will hear a "click".
(Figure J)
J
6. To test if the line is advancing properly, push
the button with your thumbs while pulling the
wire with your ngers. The line should advance
freely.
OPTION 1: ACCESSORY REPLACEMENT
SPOOL
Use replacement spool.
OPTION 2: REWINDING SPOOL USING
LINE
Line for your trimmer is available at extra cost
from your local dealer. To install line, follow
the steps below (Use 1.6mm diameter round
Nylon line only).
1. Insert one end of line into the hole in the
spool as shown Figure K about 3 mm.
tighten the height adjustment knob.
G
REPLACE THE SPOOL OF
NYLON LINE
1. Remove the battery.
2. Remove the spool assembly from the
trimmer. To do so, hold the outer ribbed part
of the assembly with one hand, while pushing
down and turning the spool head with the
other to unlock it (Figure H). The spool carrier
and spool will now disassemble easily.
Note: There is a spring inside the head that
could easily be lost. Ensure that it is put in a
safe place.
H
3. Choose either OPTION 1 or OPTION 2
below for spool or line replacement.
4. Insert the line through the eyelet in the
spool carrier and slide the spool into it. (Figure
I)
A
B
Front handle
Nut
Bolt
Tube
Height adjustment knob
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
2. Snugly and evenly wind the line onto the
spool in the direction of the arrow on the
spool,(Figure K),until the line builds up to the
notches in the spool rim. Do not overll spool.
The spool holds about 6.5 m of line.
K
Cordless Grass Trimmer
ORIGINAL INSTRUCTIONS
WARNING!
The vibration emission value during actual use of the power tool can differ form the declared value
depending on the ways in which the tool is used dependant on the following examples and other
variations on how the tool is used:
How the tool is used and the materials being cut.
The tool being in good condition and well maintained.
The correct accessories for the tool are being used and are in good condition.
The tightness of the grip on the handles and any anti vibration accessories are used.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand vibration syndrome if the use is not adequately managed.
WARNING!
To be accurate, an estimation of exposure level in the actual conditions of use should also take
account of all parts of the operating cycle such as the times when the tool is switched off and
when it is running idle but not actually doing the job. This may signicantly reduce the exposure
level over the total working period.
Help to minimize your vibration exposure risk.
Maintain this tool in accordance with these instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti vibration accessories.
Plan your work schedule to spread any high vibration tool use across a number of days.
3 mm
MAINTENANCE
Always remove the battery pack before
cleaning or repair.
Never use water or chemical cleaners to clean
the unit.
Your grass trimmer requires no additional
lubrication or maintenance.
Always clean the grass trimmer immediately
after use.
Always store the grass trimmer in a dry place.
Inspect the grass trimmer before each use.
Have the unit professionally repaired if any
damage occurs.
Keep the motor ventilation slots clean.
Keep all working controls free of dust.
A weighted sound pressure
A weighted sound power
Wear ear protection
Typical weighted vibration
NOISE AND VIBRATION DATA
82dB(A) K PA: 3dB(A)
94dB(A) K PA: 3dB(A)
2.3m/s2 K=1.5m/s
2
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist.
Check with your Local Authority or retailer for recycling advices.
Model No.
Voltage
Battery type
No-load speed
Cutting width
Battery capacity
Battery charging time
TECHINICAL DATA
N0E-2ET-230
Ni-Cd
18VDC
8000 /min
230 mm
1300 mAh
3-5 hours
GUARANTEE
This product is selected for DOMESTIC USE ONLY and not for business use. This product is
guaranteed against manufacturing defects for a period of 12 months. This does not cover the
product where the fault is due to misuse, abuse, use in contravention of the instructions, or
where the product has been the subject of unauthorised modications or alterations, or has been
the subject of commercial use. In the event of a problem with the product within the guarantee
period please return it to your nearest Argos store. If the item is shown to have an inherent defect
present at the time of sale, the store will provide you with a replacement. Your statutory rights
remain unaffected.
Guarantor: Argos, MK9 2NW
Issue1 11/2010
HOME RETAIL GROUP
EC DECLARATION OF CONFORMITY
We
Home Retail Group
Avebury, Milton Keynes,
MK9 2NW
declare that the product
N0E-2ET-230 Cordless Grass Trimmer
Function: Cutting grass and similar soft vegetation and for trimming grass edges
Complies with the requirements of the following directives:
2004/108 EC - EMC Directive.
2006/95 EC - Low Voltage Directive.
93/68 EC - CE Marking Directive
2006/42 EC - Machinery Directive
2000/14/EC - Noise emission in the environment by equipment for use outdoors
Directive.
- Conformity assessment procedure as per ANNEX VI.
- Measured Sound Power Level = 89dB(A)
- Declared Guaranteed Sound Power Level = 94dB(A)
Notied body name: Intertek Testing & Certication ltd
Notied body address: davy Avenue, knowlhill, Milton keynes, Mk5 8Nl
Notied body number: 0359
Technical documentation holder: Home Retail Group, MK9 2NW
Standards and technical specications referred to:
EN 60745-1:2006 EN 60745-1:2009 EN 786:1996+A1:2001+A2:09
ISO 11094:1991 EN ISO 3744:1995
Authorised Signatory
Date: 27.10.2010
Signature:
Name: Roger Panton-Kent
(EC conformity mark)
Head of Quality Assurance
Loading...