PLEASE READ THIS MANUAL
™
D
E
S
I
G
N
C
E
R
T
I
F
I
E
D
BEFORE INSTALLING AND US
ING APPLIANCE.
-
IMPORTANT:
Read all instructions and warnings carefully before starting installation. Failure
to follow these instructions may
result in a possible fire hazard
and will void the warranty.
WARNING: If the information
in this manual is not followed
exactly, a fire or explosion may
result causing property damage,
personal injury or loss of life.
— Do not store or use gasoline
or other flammable vapors and
liquids in the vicinity of this or
any other appliance.
— What to Do If You Smell Gas
• Do not try to light any appli-
ance.
• Do not touch any electrcal
switch; do not use any phone
in your building.
• Immediately call your gas
supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas
supplier, call the fire depart
ment.
Vent-Free Gas Room Heaters
Models: UVC36 / UVS36
UVC43 / UVS43
-
— Installation and service must
be performed by a qualified
Homeowner's Installation and
Operating Manual
installer, service agency or the
gas supplier.
This is an unvented gas-fired
heater. It uses air (oxygen) from
the room in which it is installed.
Provisions for adequate combustion and ventilation air must be
provided. Refer to Page 4.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
20000135 9/05 Rev. 4
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
Table Of Contents
PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE.
Thank you and congratulations on your purchase of a Vermont Castings, Majestic Products fireplace.
IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these
instructions may result in a possible fire hazard and will void the warranty.
Installation & Operating Instructions
Important Curing/Burning Instructions .................................................................................3
Fireplace Dimensions ..........................................................................................................4
Safety Devices ....................................................................................................................5
Description ..........................................................................................................................5
Minimum Clearances ...........................................................................................................5
Mantels ...............................................................................................................................5
Hearth Extension .................................................................................................................6
Planning ..............................................................................................................................6
Mounting the Heater ............................................................................................................6
Framing 6
Insulating for Cold Climates ................................................................................................6
Gas Specifications ...............................................................................................................7
Gas Inlet and Manifold Pressures ....................................................................................... 7
Gas Supply Pressures .........................................................................................................7
High Elevations ...................................................................................................................7
Connect the Gas Line ..........................................................................................................7
Electrical Connection ...........................................................................................................8
Hard (Direct) Wire Hook-Up ................................................................................................ 8
EB1 (Receptacle) Hook-Up ................................................................................................. 8
Remote Wall Switch ............................................................................................................ 8
Alternate Switch Location ....................................................................................................9
Slide Heater in Place ...........................................................................................................9
Level and Secure the Heater ...............................................................................................9
Finishing .............................................................................................................................. 9
Operating Instructions
Glass Information .............................................................................................................. 10
Louvre Removal ................................................................................................................ 10
Window Frame Assembly Removal ...................................................................................10
Glass Cleaning .................................................................................................................. 10
Log Installation .................................................................................................................. 10
Ember Material Placement ................................................................................................ 11
Lava Rock ......................................................................................................................... 11
Flame Adjustment .............................................................................................................. 11
Flame Characteristics ........................................................................................................ 11
First Firing ......................................................................................................................... 11
Lighting and Operating Instructions .................................................................................. 12
Troubleshooting Gas Control (NOVA SIT 820) .................................................................. 13
Maintenance
Cleaning the Standing Pilot Control System .....................................................................14
Cleaning Catalytic Filters (UVC Only) ............................................................................... 14
Replacement Parts ..................................................................................................................... 15
Optional Accessories
Fan Kit ............................................................................................................................... 17
Hard (Direct) Wire Hook Up ..............................................................................................17
Remote Controls ...............................................................................................................17
Ceramic Refractory Panels ...............................................................................................17
Arched Door Front .............................................................................................................17
Decorative Frame Trim ...................................................................................................... 18
Decorative Bay Window .................................................................................................... 18
EB-1 Electrical Box ............................................................................................................ 18
Outside Air Termination .....................................................................................................18
Warranty .......................................................................................................................................19
2
20000135
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
Installation & Operating Instructions
This gas room heater should be installed by a qualified installer
in accordance with local building codes and with current National Fuel Gas Code. ANSI Z223.1/NFPA 54.
"This heater shall not be installed in a confined space or
unusually tight construction unless provisions are provided for
adequate combustion and ventilation air".
"The National Fuel Gas Code, ANSI Z233.1/NFPA 54 defines
a confined space as a space whose volume is less than 50
cubic feet per 1,000 Btu per hour (4.8m3 per kw) of the aggregate input rating of all appliances installed in that space
and an unconfined space as a space whose volume is not less
than 50 cubic feet per 1,000 Btu per hour (4.8 m3 per kw) of the
aggregate input rating of all appliances installed in that space
and an unconfined space as a space whose volume is not less
than 50 cubic feet per 1,000 Btu per hour (4.8m3 per kw) of the
aggregate input rating of all appliances installed in that space..
Rooms communicating directly with the space in which the
appliances are installed, through openings not furnished with
doors, are considered a part of the unconfined space.
WARNING:
smaller than that defined as an unconfined space of if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods, described in the
National Fuel Gas Code, ANSI Z 223.1/NFPA 54, Section 5.3 or
applicable local codes."
Unusually tight construction is defined as construction where:
a) Walls and ceilings exposed to the outside atmosphere have
a continuous water vapor retarder with a rating of 1 perm (6
x 10-11 kg per pa-sec-m2) or less with openings gasketed or
sealed, and
b) Weather stripping has been added on openable windows
and doors, and
c) Caulking or sealants are applied to areas such as joints
around window and door frames, between sole plates and
floors, between wall-ceiling joints, between wall panels, at
penetrations for plumbing, electrical, and gas lines, and at other
openings.
If the area in which the heater may be operated is
Fireplace screen (when equipped) must be closed while
the appliance is in operation.
WARNING: Do not allow LP tank below 1/4 full.
WARNING: Do not allow fans to blow directly into the
fireplace. Avoid any drafts that alter burner flame pat
terns.
WARNING: Do not use a blower insert, heat exchanger
or other accessory not approved for use with this
heater.
WARNING: Any change to this heater or its controls
can be dangerous.
This appliance may be installed in an aftermarket,
permanently located, manufactured (mobile home),
where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases.
FOR SAFE INSTALLATION AND OPERATION OF YOUR VER
MONT CASTINGS MAJESTIC PRODUCTS COMPANY VENTFREE ROOM HEATER PLEASE NOTE THE FOLLOWING:
1. This heater gives off high temperatures and should be
located out of high traffic areas and away from furniture and
draperies.
2. Children and adults should be alerted to the hazards of the
high temperatures surface of this heater and should stay
away to avoid burns or ignition of clothing.
3. Young children should be carefully supervised when they
are in the same room as your heater.
4. Under no circumstances should this heater be modified.
Parts removed for service should be replaced prior to operating this heater again.
5. Installation repair to this heater should be done by a qualified service person. A professional service person should be
contacted to inspect this heater annually. Make it a practice
to have all of your gas heaters checked annually. More frequent cleaning may be required due to excess lint and dust
from carpeting, bedding material, etc.
6. Control compartments, burners and air passages in this
heater should be kept clean and free of dust and lint. Make
sure that the gas valve and pilot light are turned off before
you attempt to clean this unit.
7. Under no circumstances should any solid fuels (wood, coal,
paper or cardboard, etc.) be used in this heater.
8. Keep the area around your heater clear of combustible ma
terials, gasoline and other flammable vapor and liquids. This
heater should not be used as a drying rack for clothing, nor
should Christmas stockings or decorations be hung in the
area of it.
9. Whether the heater is installed directly on carpeting, vinyl
tile or any combustible material other than wood, this heater
must be installed on a metal or wood panel extending the
full width and depth of the heater.
10. Do not install heater in bedroom or bathroom.
11. Do not place clothing or other flammable material on or near
the appliance.
12. Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the heater.
13. Do not use this room heater if any part has been under
water.
-
This appliance is intended for supplemental heating.
WARNING: Do not install televisions or other electronic devices above this fireplace unless approved
by the electronics manufacturer.
Proposition 65 Warning: Fuels used in gas, wood-
burning or oil fired appliances, and the products of
combustion of such fuels, contain chemicals known to
the State of California to cause cancer, birth defects
and other reproductive harm.
California Health & Safety Code Sec. 25249.6
-
-
20000135
3
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
36"
34³⁄₄"
32³⁄₄"
5³⁄₄"
3¹⁄₄"
7³⁄₄"
2"
21"
1"
20"
9"
4"
33"
34¹⁄₄"
36"
36"
51"
25¹⁄₂"
Rough Opening Width 36¹⁄₂"
Finished Wall
Thickness
Gas Line
Access 2" Dia.
Electrical Cable
Knockout 1" Dia.
Electrical Box
Knockout 2" Dia.
Rough
Opening
Height
14¹⁄₂"
Rough
Opening
Depth
8¹⁄₂"
5¹⁄₂"
Outside
Air
Electrical Cable
Knockout 1" Dia.
Gas Line Access 2" Dia.
43"
37¹⁄₂"
35¹⁄₂"
7"
3³⁄₄"
8¹⁄₄"
2"
23¹⁄₂"
1"
31"
12¹⁄₂"
4"
40"
37"
44"
44"
62¹⁄₄"
31"
Rough Opening Width 43¹⁄₂"
Finished Wall
Thickness
Gas Line
Access 2" Dia.
Electrical Cable
Knockout 1" Dia.
Electrical Box
Knockout 2" Dia.
Rough
Opening
Height
16¹⁄₂"
Rough
Opening
Depth
8¹⁄₂"
5¹⁄₂"
Outside
Air
Electrical Cable
Knockout 1" Dia.
Gas Line Access 2" Dia.
UVC/UVS36 Vent Free Room Heater
Fig. 1 UVC/UVS36 specifications and framing.
Fig. 2 UVC/UVS43 specifications and framing.
4
UVC/UVS43 Vent Free Room Heater
0135
0135
20000135
A B C D E
V
W
X
Y
Z
Fireplace
J
F
G
H
I
Mantel
Leg
O
N
M
L
K
IMPORTANT:
Please Review the Following Carefully
It is normal for fireplaces fabricated of steel to give off some
expansion and/or contraction noises during the start up or cool
down cycle. Similar noises are found with your furnace heat
exchanger or car engine.
It is not unusual for your gas fireplace to give off some odor the
first time it is burned. This is due to the curing of the paint and
any undetected oil from the manufacturing process.
Please ensure that your room is well ventilated - open all
windows.
It is recommended that you burn your Vermont Castings Majestic
Products fireplace for a least six (6) hours the first time you use
it. If optional fan kit has been installed, place fan in the "OFF"
position during this time.
Safety Devices
Adequate combustion and ventilation air must be provided. The flow of combustion and ventilation air MUST
NOT be obstructed.
Provide adequate clearances around the air opening
into the combustion chamber; and adequate accessibility clearance for servicing and proper operation. NEVER
obstruct the front opening of the heater or cover the top
and bottom louvres (grilles).
These heaters are equipped with a pilot system featuring an Oxygen Depletion Sensor (O.D.S.) shut-off
device. All unvented heaters are required to have this
system. The O.D.S. pilot will shut down the heater
when there is not enough fresh air available.
Report any parts damaged in shipment to your dealer.
Description
The UVC vent-free heaters are unique in featuring two
catalytic filters and a frame window with glass that actually
clean room air as well as give excellent zone heating.
The UVS vent-free heaters use a frame window with
screen mesh that does not use any catalytic filters.
Each model is available as Natural or Propane gas,
equipped with a standing pilot.
Design-certified to ANSI Z21.11.2a-2003. Gas-Fired
Room Heaters — Vol. II, Unvented Room Heaters.
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
Top Louvre
Assembly
Top of
Combust io n Chamber
Bottom of Door Trim
Ref. Mantel Ref. Mantel From Top
Shelf Depth of Comb. Chamber
V 10" (254 mm) A 19" (483mm)
W 8" (203 mm) B 17" (432mm)
X 6" (152 mm) C 15" (381mm)
Y 4" (101 mm) D 13" (330mm)
Z 2" ( 51 mm) E 11" (279mm)
Fig. 3a Combustible mantel minimum installation.
CFM164a
Side of
Combustion Chamber
CFM146
Clearance to Combustibles
Top of unit to ceiling 36" (914 mm)
Front of unit to combustibles 36 (914 mm)
Appliance
Top .............................................................. 0" (0 mm)
Bottom ......................................................... 0" (0 mm)
Sides ........................................................... 0" (0 mm)
Back ........................................................... 0" (0 mm)
Perpendicular sidewall ............................ 6" (152 mm)
20000135
CFM170
Mantel Mantel Leg From Side
Ref. Leg Depth Ref. of Comb. Opening
F 10" (254 mm) K 11¹⁄₂" (292 mm)
G 8" (203 mm) L 9
H 6" (152 mm) M 7
I 4" (101 mm) N 5
J 2" ( 51 mm) O 3
Fig. 3b Combustible mantel leg minimum installation.
¹⁄₂" (241 mm)
¹⁄₂" (191 mm)
¹⁄₂" (101 mm)
¹⁄₂" (89 mm)
5
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
A
B
C
Mantels
Depending on the width of the mantel it may be installed higher or lower from the combustion chamber
opening. This also applies to the distance between the
mantel leg (if installed) and the fireplace. Refer to Figures 3a and 3b for correct mounting heights and widths
for combustible mantels and mantel legs.
Noncombustible mantels and legs may be installed at
any height above the appliance opening.
When using paint or lacquer to finish the
mantel, such paint or lacquer must be heat
resistant to prevent discoloration.
Hearth Extension
A hearth extension in front of heater is recommended
but not required.
Planning
Planning the installation is an important first step: it will
save time and money later in the actual installation. In
planning the installation, consider:
1. Where the heater will be located.
2. All components needed to complete the
project.
Mounting the Heater
The heater should only be mounted on the following
surfaces:
• A flat combustible (burnable) surface.
• A raised wooden platform.
• A concrete block or other solid object placed be
neath each of the four corners of the heater.
To mount the heater:
1. Choose unit location.
2. Place unit in position and secure to floor with 1
screws, or nails. The holes to secure the unit to the
floor are located just behind the bottom louvre on the
left and right hand side of the unit.
3. Frame in heater with a header across the top. It is
important to allow for finished face when setting the
depth of the frame.
4. Attach heater to frame using adjustable frame drywall
strips (located behind access door for shipping). Preset
depth to suit facing material (adjustable to 1/2" , 5/8" or
3/4" depths). (Fig. 4)
5. Use existing screws in side of unit to attach drywall
strip. Measure from face of heater to face of drywall
strip to determine final depth. (Fig. 4)
-
¹⁄₂"
Adjustable Drywall Strip
(Nailing Flange)
Scew Drywall
Position Depths
A 1/2" (13 mm)
B 5/8" (16 mm)
C 3/4" (19 mm)
Adjustable
1/2", 5/8" & 3/4"
Spacing
Fig. 4 Adjustable drywall strip (nailing flange).
FP1023
Framing
Framing can take place before or after the heater is set
in place. The framing should be positioned to accommodate the wall covering and facing material. Framing
material should be 2x4 or heavier. Framing headers
may rest on top of heater. (Refer to Page 4, Figures 1
and 2 for heater and framing dimensions.)
Insulating for Cold Climates
When a heater is installed in a chase or an outside wall,
the enclosure should be insulated like any other wall
of the home. Insulation should be installed under the
heater and on the inside of the exterior walls. (Fig. 5)
NOTE: Insulating for cold climates is strictly a recommendation and not a requirement.
Insulation
Insulation
methods
shown are
optional for
cold climate,
not a requirement for unit
operation.
FP456
Fig. 5 Insulating for cold climates.
6
20000135
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
Parts Identification
Nailing
Flange
Gas
Line
Access
FP443
Fig. 6 Parts identification.
Catalytic Filters
(Behind Grille)
UVC
Top Louvre
Screen Panel (UVS)
Glass Panel (UVC)
Logs and Burner
Firebox
Bottom Louvre
(Bottom Access Door)
(Controls behind louvre)
Gas Specifications
Max. Min.
Model Fuel Gas Control Input Input
B.T.U.H. B.T.U.H.
UVC36RN Natural Millivolt Hi/Lo 25,000 17,500
UVC36RP Propane Millivolt Hi/Lo 25,000 18,750
UVS36RN Natural Millivolt Hi/Lo 25,000 17,500
UVS36RP Propane Millivolt Hi/Lo 25,000 18,750
UVC43RN Natural Millivolt Hi/Lo 33,000 23,100
UVC43RP Propane Millivolt Hi/Lo 33,000 24,750
UVS43RN Natural Millivolt Hi/Lo 33,000 23,100
UVS43RP Propane Millivolt Hi/Lo 33,000 24,750
UVC36 / UVS36 / UVC43 / UVS43
Certified To
ANSI Z 21.11.2a-2003
Unvented Room Heaters
Units: B42A00, B42B00, D42A00, D42B00, B41AS0,
B41BS0, D41AS0, D41BS0
Gas Inlet and Manifold Pressures
Natural LP
Minimum Inlet Pressure 5.5" w.c. 11.0" w.c.
Maximum Inlet Pressure 14.0" w.c. 14.0" w.c.
Manifold Pressure 3.5" w.c 10.0" w.c.
High Elevations
Input ratings are shown in BTU per hour and are
certified without deration from elevations up to
4,500 feet (1,370m) above sea level.
Nuisance outages may occur at altitudes above
4,500 feet (1,370m) if dirt, dust, lint and/or cobwebs are allowed to accumulate on burner and/or
ODS pilot. Monthly inspection and cleaning is
recommended for altitudes above 4,500 feet
(1,370m)
For elevations above 4,500 feet (1,370m), installations must be in accordance with the current
ANSI Z223.1/NFPA 54 and/or local codes having
jurisdiction.
The installation of your Majestic Fireplaces roomheater must conform with local codes, or in the
absence of local codes, with National Fuel Gas
Code, ANSI Z223.1/NFPA 54 — latest edition. (EXCEPTION: Do not derate this appliance for altitude.
Maintain the manifold pressure at 3.5 inches w.c.
for Natural Gas and 10 inches w.c. for LP gas.)
Gas Supply Pressures
This heater must be isolated from the gas supply piping
system by closing its individual manual shut-off valve
during any pressure equal to or less than 1/2 psig (3.45
kPa).
The heater and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psig (3.45 kPa).
Connect the Gas Line
If gas piping from the source to the heater location has
not been accomplished, install the required pipe. Consult local plumbing code to assure proper pipe size.
The gas pipeline can be brought in through the right or
left side of the heater, as well as the bottom. Knockouts
are provided at convenient locations to allow for the gas
pipe installation and testing of any gas connection. It is
most convenient to bring the gas line in from the right
side, as this allows fan installation or removal without
disconnecting the gas line.
NOTE: The gas line connection can be made with
properly tinned 3/8" copper tubing, 1/2" rigid pipe or an
approved flex connector, then reduced to 3/8" to the
heater. Because some municipalities have some additional local codes, it is always best to consult your local
authority. Consult the current National Fuel Gas Code,
ANSI Z223.1/NFPA 54.
20000135
7
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
OUTSIDE
FRONT OF UNIT
INSIDE
FRONT OF UNIT
Always check for gas leaks with a mild soap
and water solution. Do not use an open
flame for leak testing.
The gas control is equipped with a captured screw type
pressure test point, therefore it is not necessary to provide a 1/8" test point up stream of the control.
When using copper or flex connector use only approved
fittings.
Always provide a union so the gas line can
be easily disconnected for burner or fan servicing.
See gas specification for pressure details and ratings.
NOTE: If flex connector is used, it must be kept inside
of the heater. (Fig. 7)
1/2" Gas Supply
1/2" x 3/8" Shut Off Valve
3/8" Nipple
3/8" Union
FP297
Fig. 7 Typical gas supply installation.
Electrical Connection
When installed, the heater must be electrically connected and grounded in accordance with local codes or, in the absence
of local codes:
U.S. Installations: Follow local codes and the National
Electrical Code, ANSI/NFPA No. 70.
NOTE: 110/120 electric power is required to operate
blower (fan).
Be sure to leave sufficient excess wire in case minor
adjustments are required.
Any electrical re-wiring of this fan must be
Whether wiring directly to the fan junction box or into
the EB1 (electrical receptacle box, P/N ZA1200) first
ensure cable is secured using box connector.
done by a qualified electrician.
Turn off all power before hook-up.
3/8"
Nipple
Temperature
Fan
Sensor
Speed
Control
Black
White
Ground
FP394
Fig. 8 Wiring diagram.
EB1 (Receptacle) Hook-Up
1. Remove 2" knockout. Slide the electrical box back
plate into the back and bottom lances (clips) while fitting the box connector into the knockout. Fasten into
place with fastening screws provided. (Fig. 9)
2. Connect the black positive wire to brass screw
(polarized side) of the receptacle. The white wire is
connected to the chrome screw. The ground wire is
connected to the green ground screw of the receptacle. Fit the receptacle into the electrical box.
3. Screw the cover plate provided to the electrical box.
Electrical Box
Fastening Screws
Gas Inlet Hole
Gas Inlet Hole
FP298
Fig. 8 Junction box (EB-1) hook-up.
Hard (DIrect) Wire Hook-Up:
First connect ground wire to ground stud located on
the base of either box. Black wire from supply should
connect to the variable speed switch. Alternate speed
switch wire connects to temperature sensor. Alternate
lead from sensor connects to fan. Alternate fan con-
nects back to white supply wire. (Fig. 8)
8
Remote Wall Switch
CAUTION: Do not wire millivolt remote wall
switch for gas heater to a 120v power supply. For lighting instructions, see Page 12.
1. Thread wire through the electrical knockout
located on either side of unit. Do not cut wire or insulation on metal edges. Ensure that wire is protected.
Run the other end to a conveniently located wall
receptacle box.
20000135
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
P
I
L
O
T
THTP
TP
TH
2. Attach wire to switch and install switch into receptacle box. Attach cover plate to switch.
3. Connect wiring to gas valve. (Fig. 10)
Valve
ON/OFF
Switch
FP382
Fig. 10 Remote switch wiring.
Alternate Switch Location
Remote switch can be installed on either side of the
access door. Simply mount the switch to the switch
bracket provided. Screw the bracket on either side of
the frame, lining up the screws with the pre-punched
holes. (Fig. 11)
Slide the Heater in Place
With the electrical and wall switch wiring connected,
gently slide or lift the heater to the desired location.
Level and Secure the Heater
If nailing flanges are not already installed, attach
flanges with the screws provided.
Make sure heater is level. Shimming may be required.
Secure heater in place by nailing or screwing through
nailing flanges into framing. NOTE: Be sure to allow
proper space for sheet rock.
Finishing
CAUTION: All joints between the finished wall and the
heater surround (top and sides) may be sealed only
with non-combustible material. Only noncombustible
material can be applied as facing to the heater surround
(the black painted face).
When finishing the heater, never obstruct or modify the
air inlet/outlet top or bottom grilles in any manner.
Finish the wall with the material of your choice. Refer to
Page 5, Figure 3 for specific clearances when installing
a combustible mantel or other combustible projection.
Fig. 11 Installing remote switch bracket.
Prepunched
Holes
FP381
20000135
9
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
1.
2.
Operating Instructions
Glass Information
(UVC Only)
Only glass approved by CFM Specialty
Home Products should be used on this
fireplace.
• The use of any non-approved replacement glass will
void all product warranties.
• Care must be taken to avoid breakage of the glass.
• Do not operate appliance with glass front re-
moved, cracked or broken.
• Replacement glass (complete with gasket) is
available through your CFM Specialty Home
Products dealer and should only be installed by
a licensed qualified service person.
Louvre Removal
To remove the top
louvre (grille), lift louvre up and then out.
(Fig. 12)
Window Frame
FP444
Fig. 12 Louvre installation and
removal.
Window Frame Assembly Removal
1. Shut off gas. (See Lighting Instructions)
2. Let the unit cool if it has been operating.
3. Remove top louvre. (See Top Louvre Removal)
4. Open the bottom louvre assembly.
5. Release the two clamps at the bottom of the window
frame by pulling down on the clamp handles.
6. Lift off the window frame assembly as shown in
Figure 13.
7. To reinstall window frame assembly follow the above
procedure in reverse. (Fig. 13)
Glass Cleaning
It will be necessary to clean the glass periodically. During start-up, condensation, which is normal, forms on
the inside of the glass and causes lint, dust and other
airborne particles to cling to the glass surface. Also,
initial paint curing may deposit a slight film on the glass.
It is therefore recommended that the glass be cleaned
two or three times with anon-ammonia household
10
Assembly
Grille
(Louvre)
Fireplace
Front
DV34-2
Clamps
Window
Frame
Window
Frame Assembly
Fig. 13 Window Frame installation and removal.
Push
Clamp
Hook
Assembly
Pull
Clamp
Hook
FP1000
cleaner and warm water (we recommend gas fireplace
glass cleaner). After that the glass should be cleaned
two or three times during each heating season depending on the circumstances present.
Clean glass after first two weeks of operation.
Log Installation
Refer to Figures 14 and 15 for correct log placement.
1. Remove window frame assembly. (See "Window
Frame Assembly" section)
2. Remove logs from packaging.
As with all plastic - these are not toys and
should be kept away from children and
infants.
3. Place rear log (BE8 or BF10) on rear bracket (ensure
log is seated properly, leveled and centered to the
unit), so it will not move from side to side and it is
firmly positioned on the bracket.
4. Place front left log (BE6 or BF8) on top of burner, left
side. Use log's bottom holes to locate it onto the left
bracket log locator studs.
5. Place front right log (BE7 or BF9) on top of burner,
right side. Use log's bottom holes to locate it onto
the left bracket log locator studs.
6. Place ember material on top of burner. (See "Ember
Material Placement" section).
20000135
7. Place top left log (BE9 or BF11) onto locator notches.
LO
HI
Turn
counterclockwise
to decrease
flame height
Turn clockwise
to increase
flame height
Ensure log is secure.
8. Place top right log (BE10 or BF12) onto locator
notches. Ensure log is secure.
BE9
BE10
BE8
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
Fig. 16 Flame adjustment knob for Honeywell Valve.
BE6
Fig. 14 UVC/UVS36 log placement.
BF10
BF8
Fig. 15 UVC/UVS43 log placement.
Separate the ember material into small pieces and
place onto the burner in front of the front logs. Do NOT
pack down, leave in fluffy, loose condition for most realistic ember effects. Do not install more embers on
the burner than come with the unit.
Application of excess loose material may adversely
affect performance of theheater.
Replacement loose embers must be purchased
through authorized Majestic Fireplaces dealers.
The lava rock provided with this fireplace must be
placed on the firebox bottom on either side of the
burner assembly. Do not place lava rock in combustion
pan.
For fireplaces equipped with HI/LO valves, flame adjustment is accomplished by rotating the HI/LO adjustment knob located near the center of the gas control.
(Fig. 16)
20000135
BE7
LG131
BF11
BF12
BF9
LG132
Ember Material Placement
WARNING: All previously applied loose
material must be removed prior to reapplication.
Lava Rock
Under no circumstances should this lava
rock be placed on any part of the burner
assembly.
Flame Adjustment
Flame Characteristics
It is important to periodically perform a visual check
of the pilot and burner flames. Compare them to the
Figures 17 or 18. If the flame patterns appear abnormal, contact a qualified service provider for service and
adjustment.
FP449
Fig. 17 Correct pilot flame pattern.
UVC36/UVS43
LG133
UVC43/UVS43
LG134
Fig. 18 Approximate flame heights for each model.
First Firing
Upon completing the gas line connection, a small
amount of air will be in the lines. When first lighting unit
with pilot light, it will take a few minutes to purge themselves of this air. Once the purging is complete, the
pilot and burner will light and operate as indicated in the
instruction manual. Subsequent lightings of the heater
will not require such purging.
When lit for the first time, the appliance will emit a slight
odor for awhile. This is due to paint and lubricants used
in the manufacturing process. After each lighting, vapor
may condense and fog the glass; this moisture disappears within a few minutes of burning.
11
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
PILOT
ON
OFF
ON
P
I
L
O
T
O
F
F
O
F
F
5
4
3
2
1
O
F
F
P
i
l
o
t
3/8" - 1/2"
Lighting And Operating Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This heater has a pilot which must be lit manu
ally. When lighting the pilot follow these
instructions exactly.
B. BEFORE LIGHTING smell all around the heater
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any fireplace
• Do not touch any electric switch
• Do not use any phone in your building
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
Lighting Instructions
-
• If you cannot reach your gas supplier, call the
Fire Department
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualified service technician. Applying force or any
attempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under
water. Immediately call a qualified service techni
cian to inspect the heater and to replace any part of
the control system and any gas control which has
been under water.
1. STOP! Read the safety information above.
2. Turn off all electrical power to the fireplace.
3. For MN/MP/TN/TP appliances ONLY, go on to
Step 4. For RN/RP appliances turn the On/Off
switch to “OFF” position or set thermostat to
lowest level.
4. Open control access panel.
5. Push in gas control knob slightly and turn
clockwise to "OFF".
Euro SIT SIT NOVA
Honeywell
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow "B" in the safety information above. If you do not smell gas, go to the
next step.
7. Remove glass door before lighting pilot. (See
Glass Frame Removal section).
8. Visibly locate pilot by the main burner.
9. Turn knob on gas control counterclockwise
to "PILOT".
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly depressing the piezo spark ignitor until a flame appears.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 8.
• If knob does not pop up when released, stop
and immediately call your service technician or
gas supplier.
• If after several tries, the pilot will not stay lit,
turn the gas control knob to "OFF" and call your
service technician or gas supplier.
11. Replace glass door.
12. Turn gas control knob to “ON” position.
13. For RN/RP appliances turn the On/Off switch to
“ON” position or set thermostat to desired setting.
14. Turn on all electrical power to the fireplace.
1. Turn the On/Off switch to Off position or set the
thermostat to lowest setting.
2. Turn off all electric power to the fireplace if
service is to be performed.
12
To Turn Off Gas To Heater
3. Open control access panel.
4. Push in gas control knob slightly and turn clockwise to "OFF". Do not force.
5. Close control access panel.
20000135
• Gas Supply On
• Supply line hooked up
• Shutoff valve open
NO
NO
NO
NO
• Lockout has engaged. Wait
60 seconds and try again
• For spark at electrode while
depressing Piezo
1/8" gap to pilot hood needed
• All wiring connections
• Replace Piezo ignitor
• For air in lines
• Thermopile needs a minimum
325mV. Adjust pilot flame height
• All wiring connections
• Replace Thermopile
• Thermocouple needs a minimum
of 14mV.
• Defective valve. turn to pilot,
meter should read greater than
100mV. If not, replace
Pilot Lights with
Piezo Ignitor
YES
YES
YES
YES
Pilot Stays Lit
Pilot Lights Main
Burner
System OK
START
CHECK
• Valve is turned on
• Wall switch is not turned on.
Watch for grounded wires!
• Thermopile needs a minimum
325mV.
• Plugged burner orifice
Nova SIT 820
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
Troubleshooting
20000135
FP396A
13
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
Maintenance
Burner and Burner Compartment
It is important to keep the burner and the burner
compartment clean. At least once per year the logs and
lava rock/ember material should be removed and the
burner compartment vacuumed and wiped out. Remove
and replace the logs as per the instructions in this
manual.
Always handle the logs with care as they are fragile
and may also be hot if the fireplace has been in
use.
FK24 Fan Assembly
The fan unit requires periodic cleaning. At least once
per month in the operating season, open the lower
louvre panels and wipe or vacuum the area around the
fan to remove any build up of dust or lint.
Cleaning the Standing Pilot
Control System
The burner and control system consists of:
• main burner • pilot burner
• gas orifice • thermopile
• combination millivolt gas valve
Most of these components may require only an occasional checkup and cleaning and some may require adjustment. If repair is necessary, it should be performed
by a qualified technician.
In order to properly clean the burner and pilot assembly,
turn off the gas to the unit, remove the window frame
panel and logs exposing the burner and pilot assembly.
Clean all foreign materials from the top of the burner.
Check to make sure that burner parts are clean. Visually inspect pilot. Brush or blow away any dust or lint
accumulation If pilot orifice is plugged, disassembly
may be required to remove any foreign material from
the orifice or tubing.
To obtain proper operation, it is imperative that the pilot
and burner's flame characteristics are steady, not lifting
or floating.
Typically, the top 1/8" of the thermopile should be engulfed in the pilot flame. (Fig. 19)
Pilot Assembly
FP449
Fig. 19 Proper pilot flame height.
Cleaning Catalytic Filters
(UVC Only)
The catalytic filters require cleaning at least once a year
to work effectively.
To clean catalytic filters:
1. From inside the combustion area, remove the 4 hex
nuts holding the filter; lower filter down and out.
2. Clean the outer surface of the filter with the brush
attachment of your vacuum sweeper to remove loose
dirt.
3. Submerge the filter in a mild soapy water solution,
then rinse thoroughly with distilled or deionized
water.
4. Replace in heater when dry.
5. Repeat with second filter.
14
20000135
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
13
12
10
11
8
6a/b
22
18
17
26
7
9
23 a/b
2
3
4a/b
5
25
20a/b
27
15
28
19
1
1a
1b
1c
1d
1e
UVC/UVS36
1a
1b
1c
1d
1e
UVC/UVS43
1
14
19
21
16
24
30
CFM Specialty Home Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products
at any time, without notice.
UVC/UVS 36/43 Vent Free Heaters
Ref. Description UVC36 UVS36 UVC43 UVS43
1. Log Set Complete 10000547 10000547 10000562 10000562
1a. Log Front Left BE6 BE6 BF8 BF8
1b. Log Front Right BE7 BE7 BF9 BF9
1c. Log Rear BE8 BE8 BF10 BF10
1d. Log Top Left BE9 BE9 BF11 BF11
1e. Log Top Right BE10 BE10 BF12 BF12
2. Lava Rock Package 55255 55255 55255 55255
3. Ember Package 10000550 10000550 10000550 10000550
4a. Burner with Tiles - Natural 20000075 20000075 20000111 20000111
4b. Burner with Tiles - LP 10000555 10000555 10000152 10000152
5. Ceramic Tile (Single) 57803 57803 57803 57803
20000135
0135
15
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
UVC/UVS 36/43 Vent Free Heaters (continued)
Ref. Description UVC36 UVS36 UVC43 UVS43
6a. Orifice Main Burner - Natural See Rating Plate for Orifice Size
6b. Orifice Main Burner - LP See Rating Plate for Orifice Size
7. Fan with Bracket (FK24) 54103 54103 54103 54103
8. Electrical Cord (6ft.) 51865 51865 51865 58165
9. Fan Temperature Sensor 51704 51704 51704 51704
10. Speed Control 51738 51738 51738 51738
11. Speed Control Knob 51882 51882 51882 51882
12. Glass with Gasket 55686 - 57438 -
13. Gasket Glass 57317 - 57317 -
14. Frame Window 57937 - 57977 -
15. Frame Window w/Screen - 10000148 - 10000153
16. Access Door Hinge 52356 52356 52356 52356
17. Louvre Top Assembly 10000037 10000037 10000041 10000041
18. Louvre Bottom Assembly 10000038 10000038 10000042 10000042
19. Pilot Tubing w/Fittings 10000150 10000150 10000150 10000150
20a. Pilot Assembly - Natural ODS 55464 55464 55464 55464
20b. Pilot Assembly - LP ODS 10001647 10001647 55465 55465
21. Ignitor Piezo 52464 52464 52464 52464
22. Cable Ignitor 20000101 20000101 20000101 20000101
23a. Valve Nova - Natural 55463 55463 55463 55463
23b. Valve Nova - LP 55462 55462 55462 55462
24. Manifold Tubing w/Fittings 57318 57318 57318 57318
25. Clamp Frame Window 54174 54174 54174 54174
26. CO Catalyst Filter 55629 - 55629 -
27. Bracket CO Catalyst Holder 56255 - 56255 -
28. Remote Switch 51842 51842 51842 51842
29. Remote Switch Kit (Not Shown) 53875 53875 53875 53875
30. O.S.A. Assy 3547900 3547900 3547900 3547900
Contact CFM Specialty Home Products for questions
concerning prices and policies covering replacement
parts. Parts may be ordered through your Majestic Fireplaces distributor or dealer.
You will need the following information when ordering
replacement parts:
1. The heater model number.
2. The serial number.
3. A description of the part.
Should you need additional information beyond what
your dealer can furnish, contact:
CFM Specialty Home Products
410 Admiral Blvd.
Mississauga, Ontario
Canada, L5T 2N6
Model and serial numbers are listed on the rating
plate (located on right side of combustion chamber).
Record your model and serial numbers here for
future reference:
Model # ____________________________
Serial # ____________________________
16
20000135
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
Optional Accessories
Fan Kit
FK24 Fan Assembly
Fan specifications: 120 volt, 60 Hz, .75 Amps
This fan does not need regular maintenance, however
periodic cleaning is required. Check the area under the
control door and in front of the fan and wipe or vacuum
at least once a month during the operating season.
Should this fan require servicing, the power supply
must be disconnected.
The FK-24 comes with the electrical cord attached.
1. Slide fan assembly from the left side into the fireplace opening, line up mounting holes with screw
studs on back of fireplace and fasten with #10-24
hex nuts.
2. Install thermal sensor on bottom of firebox using
#10-24 hex nuts.
3. (Option A) - Place electronic fan speed control box
on bottom of fireplace base, lining up mounting holes
with screw studs. Fasten fan speed control box with
#10-24 hex nuts.
(Option B) - The speed control can be installed in
an electrical box at normal wall switch height for
convenient access.
4. The power supply may be connected in 2 ways:
Method A - route the 6' (1.8m) lead fitted to the unit
to a conveniently located wall socket.
Method B - If the EB-1 receptacle box (Pt.
#ZA1200) was correctly connected when the unit
was installed, the fan lead can be directly plugged
into the EB-1 plug socket.
5. Whether wiring directly to the fan junction box, (Op
tion A) or into the EB-1 (Option B), first ensure cable
is secured using box connector.
The fireplace, when installed must be electrically
connected and grounded in accordance with local
codes or, in the absence of local codes, with the
current CSA C22.1 Canadian Electrical Code or for
US installations, follow local codes and the National
Electrical Code, ANSI/NFPA No. 70.
-
Hard (Direct) Wire Hook-Up
First connect the ground wire to the ground stud located
on the base of either box. Black wire from supply
should connect to the variable speed switch. Alternate
speed switch wire connects to temperature sensor. Alternate lead from sensor connects to fan. Alternate fan
lead connects back to the white supply wire. (Fig. 20)
Any electrical rewiring of this fan must be
completed by a qualified electrician.
Turn off all power before hook-up.
Fan
FP394
Speed
Control
Black
White
Ground
Fig. 20 FK-24 wiring.
Temperature
Sensor
Remote Controls
Optional remote control units are available to control
different functions of the appliance.
Model Function(s) Controlled
MRC1 ON/OFF
MRC2 ON/OFF and Temperature
MRC3 ON/OFF and Temperature control
with a digital and a programmable
24 hour clock
IMT Wall mounted thermostat control
Ceramic Refractory Panels
Ceramic refractory panels are available to line the firebox area.
Unit Kit Model
UVC36 UV36CR
UVS36 UV36CR
UVC43 UV43CR
UVS43 UV43CR
Take care when handling the refractory panels as they
are fragile until held in place and supported.
Arched Door Front
The arched door front kit is designed to visually enhance the appearance of the UVC36 fireplace only.
DV36ADKP Polished Brass
DV36ADKA Antique Brass
20000135
17
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
Decorative Frame Trims
A selection of decorative frame trim kits are available
for mounting around the outside of the appliance to enhance its visual effect on the room. Installation instructions for each decorative frame trim are included with
the frame trim kit.
Unit Kit Model
UVC/UVS36 DV36GTP/DV36GTA
DV36TKP/DV36TKA
DV36KMP/DV36KMA
DV36KWP/DV36KWA
UVC/UVS43 DV43GTP/DV43GTA
DV43TKP/DV43TKA
DV43KMP/DV43KMA
DV43KWP/DV43KWA
Decorative Bay Window
Available for the UVC36 only.
When fitting the Bay Window Kit, the original front
frame/glass assembly MUST remain in place. The
Bay Window Kit is fitted over the existing front
glass.
Installation
1. Remove the existing louvre assembly bottom complete with the hinges.
2. Remove the louvre assembly top.
3. Assembly the Bay Window Kit according to the
instructions supplied with the kit.
4. Place the 2 pieces of ceramic refractory along the
base of the bay window. (Fig. 21)
5. Hang the bay window assembly over the existing
window frame assembly.
6. Reinstall the louvre assembly top.
7. Do not remove the existing window frame assembly.
Louvre Assembly Top
Bay
Window
Frame
Ceramic
Refractory
Bottom
Brass
Trim
Screws
Fig. 21 Bay window.
Ceramic
Refractory
Spacers
Louvre
Assembly
Bottom
FP1195
EB-1 Electrical Box
Junction box for fan installations.
Outside Air Termination
The AK-1 completes the connection from outside air kit
to out-of-doors. (Does not include 4" flex duct.)
18
20000135
LIMITED LIFETIME WARRANTY
Majestic Fireplaces® UVC / UVS Vent-Free Heaters
PRODUCT COVERED BY THIS WARRANTY
All Vermont Castings gas stoves, gas inserts, and gas fireplaces, and all Majestic or Northern Flame
BASIC WARRANTY
CFM Specialty Home Products (hereinafter referred to collectively as
the Company) warrants that your new Vermont Castings or Majestic
Gas Fireplace/Stove is free from manufacturing and material defects
for a period of one year from the date of purchase, subject to the
following conditions and limitations.
EXTENDED LIFETIME WARRANTY
The heat exchanger, where applicable, and combustion chamber
of every Vermont Castings or Majestic gas product is warranted for
life against through wall perforation. All appliances equipped with an
Insta-Flame Ceramic Burner have limited lifetime coverage on the
ceramic burner plaque. Warrantees are made to the original owner
subject to proof of purchase and the conditions and limitations listed
on this Warranty Document
COMPONENT WARRANTY
CAST IRON: All external and internal cast iron parts are warranted for a
period of three years.
Note: On porcelain enamel finished external parts and accessories
The Company offers no Warranty on chipping of enamel surfaces.
Inspect all product prior to accepting it for any damage to the
enamel.
The salt air environment of coastal areas or a high humidity
environment can be corrosive to the porcelain enamel finish. These
conditions can cause rusting of the cast iron beneath the porcelain
enamel finish, which will cause the finish to flake off.
Dye lot variations with replacement parts and/or accessories can
occur and are not covered by warranty.
GLASS DOORS: Glass doors are covered for a period of one year.
Glass doors are not warranted for breakage due to misuse or accident.
Glass doors are not covered for discoloration or burned in stains due to
environmental issues, or improper cleaning and maintenance.
BRASS PLATED PARTS AND ACCESSORIES: Brass parts should be
cleaned with Lemon oil only.
mix and masonry cleaners may corrode the brass finish. The Company
will not be responsible for, nor will it warrant any brass parts which are
damaged by external chemicals or down draft conditions.
GAS VALVES: Gas valves are covered for a period of one year
ELECTRONIC AND MECHANICAL COMPONENTS: Electronic and
mechanical components of the burner assembly are covered for one
year. All steel tube burners are warranted for one year.
ACCESSORIES: Unless otherwise noted all components and CFM
Specialty Home Products company supplied accessories are covered
for a period of one year.
CONDITIONS AND LIMITATIONS
• This new Vermont Castings or Majestic product must be installed by
a competent, authorized, service contractor. A licensed technician, as
prescribed by the local jurisdiction must perform any installation/service
work. It must be installed and operated at all times in accordance with
the Installation and Operating instructions furnished with the product.
Any alteration, willful abuse, accident, or misuse of the product shall
nullify this warranty.
• This warranty is non-transferable, and is made to the original owner,
provided that the purchase was made through an authorized supplier
of the Company.
• The customer must pay for any Authorized Dealer in-home travel fees
or service charges for in-home repair work. It is the dealers option
whether the repair work will be done in the customer’s home or in the
dealer’s shop.
• If upon inspection, the damage is found to be the fault of the
manufacturer, repairs will be authorized at no charge to the customer
parts and/or labor.
Brass cleaners cannot be used. Mortar
• Any part and/or component replaced under the provisions of this
warranty is covered for six months or the remainder of the original
warranty, whichever is longest.
• This warranty is limited to the repair of or replacement of part(s) found
to be defective in material or workmanship, provided that such part(s)
have been subjected to normal conditions of use and service, after
said defect is confirmed by the Company’s inspection.
• The company may, at its discretion, fully discharge all obligations
with respect to this warranty by refunding the wholesale price of the
defective part(s)
• Any installation, labor, construction, transportation, or other related
costs/expenses arising from defective part(s), repair, replacement,
or otherwise of same, will not be covered by this warranty, nor shall
the Company assume responsibility for same. Further, the Company
will not be responsible for any incidental, indirect, or consequential
damages except as provided by law.
• SOM E STATES DO NOT ALLOW FOR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOUR
CIRCUMSTANCES. THIS WARRANTY GIVES YOU SPECIFIC
RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
• All other warranties-expressed or implied- with respect to the product,
its components and accessories, or any obligations/liabilities on the
part of the Company are hereby expressly excluded.
• The Company neither assumes, nor authorizes any third party to
assume on its behalf, any other liabilities with respect to the sale of
this Vermont Castings or Majestic product
• The warranties as outlined within this document do not apply to chimney
components or other non CFM Specialty Home Products accessories
used in conjunction with the installation of this product..
• Damage to the unit while in transit is not covered by this warranty but
is subject to claim against the common carrier. Contact the dealer
from whom you purchased your fireplace/stove (do not operate the
appliance as this might negate the ability to process the claim with the
carrier).
• The Company will not be responsible for:
a) Down drafts or spillage caused by environmental conditions such
as near-by trees, buildings, roof tops, hills, or mountains.
b) Inadequate vent ilation or negative air press ure caused by
mechanical systems such as furnaces, fans, clothes dryers, etc.
• This warranty is void if:
a) The fireplace has been operated in atmospheres contaminated by
chlorine, fluorine, or other damaging chemicals.
b) The fireplace has been subjected to prolon ged periods of
dampness or condensation
c) Any damage s to the firep lace, combusti on chamber, heat
exchanger or other components due to water, or weather damage,
which is the result of but not limited to, improper chimney/venting
installation.
d) Any alteration, willful abuse, accident, or misuse of the product
has occurred.
IF WARRANTY SERVICE IS NEEDED…
1) Contact your supplier. Make sure you have your warranty,
your sales receipt, and the model/serial number of your
CFM Specialty Home Products product.
2) DO NOT ATTEMPT TO DO ANY SERVICE WORK
YOURSELF.
20000135
19
CFM Specialty Home Products
410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777
www.majesticproducts.com • www.vermontcastings.com
Loading...